\n

SCU

Peripheral Memory Blocks

address_offset : 0x0 Bytes (0x0)
size : 0x100 byte (0x0)
mem_usage : registers
protection : not protected

Registers

ANATSECTRL

ANATSEIH

ANATSEIL

ANATSEMON

ANAVDEL

ANAOFFSET


ANATSECTRL

Temperature Sensor Control Register
address_offset : 0x24 Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

ANATSECTRL ANATSECTRL read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 TSE_EN

TSE_EN : Temperature sensor enable
bits : 0 - -1 (0 bit)
access : read-write

Enumeration:

#0 : value1

Temperature sensor is disabled

#1 : value2

Temperature sensor is switched on

End of enumeration elements list.


ANATSEIH

Temperature Sensor High Temperature Interrupt Register
address_offset : 0x30 Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

ANATSEIH ANATSEIH read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 TSE_IH

TSE_IH : Counter value for high temperature interrupt
bits : 0 - 14 (15 bit)
access : read-write


ANATSEIL

Temperature Sensor Low Temperature Interrupt Register
address_offset : 0x34 Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

ANATSEIL ANATSEIL read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 TSE_IL

TSE_IL : Counter value for low temperature interrupt
bits : 0 - 14 (15 bit)
access : read-write


ANATSEMON

Temperature Sensor Counter2 Monitor Register
address_offset : 0x40 Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

ANATSEMON ANATSEMON read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 TSE_MON

TSE_MON : Monitor Counter2 value; loaded by TSE_DONE
bits : 0 - 14 (15 bit)
access : read-only


ANAVDEL

Voltage Detector Control Register
address_offset : 0x50 Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

ANAVDEL ANAVDEL read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 VDEL_SELECT VDEL_TIM_ADJ VDEL_EN

VDEL_SELECT : VDEL Range Select
bits : 0 - 0 (1 bit)
access : read-write

Enumeration:

#00 : value1

2.25V

#01 : value2

3.0V

#10 : value3

4.4V

End of enumeration elements list.

VDEL_TIM_ADJ : VDEL Timing Setting
bits : 2 - 2 (1 bit)
access : read-write

Enumeration:

#00 : value1

typ 1us - slowest response time

#01 : value2

typ 500n

#10 : value3

typ 250n

#11 : value4

no delay - fastest response time.

End of enumeration elements list.

VDEL_EN : VDEL unit Enable
bits : 4 - 3 (0 bit)
access : read-write

Enumeration:

#0 : value1

VDEL is disabled

#1 : value2

VDEL is active

End of enumeration elements list.


ANAOFFSET

DCO1 Offset Register
address_offset : 0x6C Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

ANAOFFSET ANAOFFSET read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ADJL_OFFSET

ADJL_OFFSET : ADJL Offset register
bits : 0 - 2 (3 bit)
access : read-write

Enumeration:

0x0 : value1

- 3.75%, typ.

0x1 : value2

- 2.85%, typ.

0x4 : value3

0, default

0x5 : value4

+ 0.95%, typ.

0x8 : value5

+ 3.75%, typ.

End of enumeration elements list.



Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !

This website is sponsored by EmbeetleEmbeetle, an IDE designed from scratch for embedded software developers.