\n

FLASH0

Peripheral Memory Blocks

address_offset : 0x0 Bytes (0x0)
size : 0x1400 byte (0x0)
mem_usage : registers
protection : not protected

Registers

ID

FSR

FCON

MARP

PROCON0

PROCON1

PROCON2


ID

Flash Module Identification Register
address_offset : 0x1008 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

ID ID read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 MOD_REV MOD_TYPE MOD_NUMBER

MOD_REV : Module Revision Number
bits : 0 - 6 (7 bit)
access : read-only

MOD_TYPE : Module Type
bits : 8 - 14 (7 bit)
access : read-only

MOD_NUMBER : Module Number Value
bits : 16 - 30 (15 bit)
access : read-only


FSR

Flash Status Register
address_offset : 0x1010 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

FSR FSR read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 PBUSY FABUSY PROG ERASE PFPAGE PFOPER SQER PROER PFSBER PFDBER PROIN RPROIN RPRODIS WPROIN0 WPROIN1 WPROIN2 WPRODIS0 WPRODIS1 SLM VER

PBUSY : Program Flash Busy
bits : 0 - -1 (0 bit)
access : read-only

Enumeration:

#0 : value1

PFLASH ready, not busy; PFLASH in read mode.

#1 : value2

PFLASH busy; PFLASH not in read mode.

End of enumeration elements list.

FABUSY : Flash Array Busy
bits : 1 - 0 (0 bit)
access : read-only

PROG : Programming State
bits : 4 - 3 (0 bit)
access : read-only

Enumeration:

#0 : value1

There is no program operation requested or in progress or just finished.

#1 : value2

Programming operation (write page) requested (from FIM) or in action or finished.

End of enumeration elements list.

ERASE : Erase State
bits : 5 - 4 (0 bit)
access : read-only

Enumeration:

#0 : value1

There is no erase operation requested or in progress or just finished

#1 : value2

Erase operation requested (from FIM) or in action or finished.

End of enumeration elements list.

PFPAGE : Program Flash in Page Mode
bits : 6 - 5 (0 bit)
access : read-only

Enumeration:

#0 : value1

Program Flash not in page mode

#1 : value2

Program Flash in page mode; assembly buffer of PFLASH (256 byte) is in use (being filled up)

End of enumeration elements list.

PFOPER : Program Flash Operation Error
bits : 8 - 7 (0 bit)
access : read-only

Enumeration:

#0 : value1

No operation error reported by Program Flash

#1 : value2

Flash array operation aborted, because of a Flash array failure, e.g. an ECC error in microcode.

End of enumeration elements list.

SQER : Command Sequence Error
bits : 10 - 9 (0 bit)
access : read-only

Enumeration:

#0 : value1

No sequence error

#1 : value2

Command state machine operation unsuccessful because of improper address or command sequence.

End of enumeration elements list.

PROER : Protection Error
bits : 11 - 10 (0 bit)
access : read-only

Enumeration:

#0 : value1

No protection error

#1 : value2

Protection error.

End of enumeration elements list.

PFSBER : PFLASH Single-Bit Error and Correction
bits : 12 - 11 (0 bit)
access : read-only

Enumeration:

#0 : value1

No Single-Bit Error detected during read access to PFLASH

#1 : value2

Single-Bit Error detected and corrected

End of enumeration elements list.

PFDBER : PFLASH Double-Bit Error
bits : 14 - 13 (0 bit)
access : read-only

Enumeration:

#0 : value1

No Double-Bit Error detected during read access to PFLASH

#1 : value2

Double-Bit Error detected in PFLASH

End of enumeration elements list.

PROIN : Protection Installed
bits : 16 - 15 (0 bit)
access : read-only

Enumeration:

#0 : value1

No protection is installed

#1 : value2

Read or/and write protection for one or more users is configured and correctly confirmed in the User Configuration Block(s).

End of enumeration elements list.

RPROIN : Read Protection Installed
bits : 18 - 17 (0 bit)
access : read-only

Enumeration:

#0 : value1

No read protection installed

#1 : value2

Read protection and global write protection is configured and correctly confirmed in the User Configuration Block 0.

End of enumeration elements list.

RPRODIS : Read Protection Disable State
bits : 19 - 18 (0 bit)
access : read-only

Enumeration:

#0 : value1

Read protection (if installed) is not disabled

#1 : value2

Read and global write protection is temporarily disabled.

End of enumeration elements list.

WPROIN0 : Sector Write Protection Installed for User 0
bits : 21 - 20 (0 bit)
access : read-only

Enumeration:

#0 : value1

No write protection installed for user 0

#1 : value2

Sector write protection for user 0 is configured and correctly confirmed in the User Configuration Block 0.

End of enumeration elements list.

WPROIN1 : Sector Write Protection Installed for User 1
bits : 22 - 21 (0 bit)
access : read-only

Enumeration:

#0 : value1

No write protection installed for user 1

#1 : value2

Sector write protection for user 1 is configured and correctly confirmed in the User Configuration Block 1.

End of enumeration elements list.

WPROIN2 : Sector OTP Protection Installed for User 2
bits : 23 - 22 (0 bit)
access : read-only

Enumeration:

#0 : value1

No OTP write protection installed for user 2

#1 : value2

Sector OTP write protection with ROM functionality is configured and correctly confirmed in the UCB2. The protection is locked for ever.

End of enumeration elements list.

WPRODIS0 : Sector Write Protection Disabled for User 0
bits : 25 - 24 (0 bit)
access : read-only

Enumeration:

#0 : value1

All protected sectors of user 0 are locked if write protection is installed

#1 : value2

All write-protected sectors of user 0 are temporarily unlocked, if not coincidently locked by user 2 or via read protection.

End of enumeration elements list.

WPRODIS1 : Sector Write Protection Disabled for User 1
bits : 26 - 25 (0 bit)
access : read-only

Enumeration:

#0 : value1

All protected sectors of user 1 are locked if write protection is installed

#1 : value2

All write-protected sectors of user 1 are temporarily unlocked, if not coincidently locked by user 0 or user 2 or via read protection.

End of enumeration elements list.

SLM : Flash Sleep Mode
bits : 28 - 27 (0 bit)
access : read-only

Enumeration:

#0 : value1

Flash not in sleep mode

#1 : value2

Flash is in sleep or shut down mode

End of enumeration elements list.

VER : Verify Error
bits : 31 - 30 (0 bit)
access : read-only

Enumeration:

#0 : value1

The page is correctly programmed or the sector correctly erased. All programmed or erased bits have full expected quality.

#1 : value2

A program verify error or an erase verify error has been detected. Full quality (retention time) of all programmed ("1") or erased ("0") bits cannot be guaranteed.

End of enumeration elements list.


FCON

Flash Configuration Register
address_offset : 0x1014 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

FCON FCON read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 WSPFLASH WSECPF IDLE ESLDIS SLEEP RPA DCF DDF VOPERM SQERM PROERM PFSBERM PFDBERM EOBM

WSPFLASH : Wait States for read access to PFLASH
bits : 0 - 2 (3 bit)
access : read-write

Enumeration:

#0000 : value1

PFLASH access in one clock cycle

#0001 : value2

PFLASH access in one clock cycle

#0010 : value3

PFLASH access in two clock cycles

#0011 : value4

PFLASH access in three clock cycles

#1111 : value5

PFLASH access in fifteen clock cycles.

End of enumeration elements list.

WSECPF : Wait State for Error Correction of PFLASH
bits : 4 - 3 (0 bit)
access : read-write

Enumeration:

#0 : value1

No additional wait state for error correction

#1 : value2

One additional wait state for error correction during read access to Program Flash. If enabled, this wait state is only used for the first transfer of a burst transfer.

End of enumeration elements list.

IDLE : Dynamic Flash Idle
bits : 13 - 12 (0 bit)
access : read-write

Enumeration:

#0 : value1

Normal/standard Flash read operation

#1 : value2

Dynamic idle of Program Flash enabled for power saving; static prefetching disabled

End of enumeration elements list.

ESLDIS : External Sleep Request Disable
bits : 14 - 13 (0 bit)
access : read-write

Enumeration:

#0 : value1

External sleep request signal input is enabled

#1 : value2

Externally requested Flash sleep is disabled

End of enumeration elements list.

SLEEP : Flash SLEEP
bits : 15 - 14 (0 bit)
access : read-write

Enumeration:

#0 : value1

Normal state or wake-up

#1 : value2

Flash sleep mode is requested

End of enumeration elements list.

RPA : Read Protection Activated
bits : 16 - 15 (0 bit)
access : read-only

Enumeration:

#0 : value1

The Flash-internal read protection is not activated. Bits DCF, DDF are not taken into account. Bits DCF, DDFx can be cleared

#1 : value2

The Flash-internal read protection is activated. Bits DCF, DDF are enabled and evaluated.

End of enumeration elements list.

DCF : Disable Code Fetch from Flash Memory
bits : 17 - 16 (0 bit)
access : read-write

Enumeration:

#0 : value1

Code fetching from the Flash memory area is allowed.

#1 : value2

Code fetching from the Flash memory area is not allowed. This bit is not taken into account while RPA='0'.

End of enumeration elements list.

DDF : Disable Any Data Fetch from Flash
bits : 18 - 17 (0 bit)
access : read-write

Enumeration:

#0 : value1

Data read access to the Flash memory area is allowed.

#1 : value2

Data read access to the Flash memory area is not allowed. This bit is not taken into account while RPA='0'.

End of enumeration elements list.

VOPERM : Verify and Operation Error Interrupt Mask
bits : 24 - 23 (0 bit)
access : read-write

Enumeration:

#0 : value1

Interrupt not enabled

#1 : value2

Flash interrupt because of Verify Error or Operation Error in Flash array (FSI) is enabled

End of enumeration elements list.

SQERM : Command Sequence Error Interrupt Mask
bits : 25 - 24 (0 bit)
access : read-write

Enumeration:

#0 : value1

Interrupt not enabled

#1 : value2

Flash interrupt because of Sequence Error is enabled

End of enumeration elements list.

PROERM : Protection Error Interrupt Mask
bits : 26 - 25 (0 bit)
access : read-write

Enumeration:

#0 : value1

Interrupt not enabled

#1 : value2

Flash interrupt because of Protection Error is enabled

End of enumeration elements list.

PFSBERM : PFLASH Single-Bit Error Interrupt Mask
bits : 27 - 26 (0 bit)
access : read-write

Enumeration:

#0 : value1

No Single-Bit Error interrupt enabled

#1 : value2

Single-Bit Error interrupt enabled for PFLASH

End of enumeration elements list.

PFDBERM : PFLASH Double-Bit Error Interrupt Mask
bits : 29 - 28 (0 bit)
access : read-write

Enumeration:

#0 : value1

Double-Bit Error interrupt for PFLASH not enabled

#1 : value2

Double-Bit Error interrupt for PFLASH enabled. Especially intended for margin check

End of enumeration elements list.

EOBM : End of Busy Interrupt Mask
bits : 31 - 30 (0 bit)
access : read-write

Enumeration:

#0 : value1

Interrupt not enabled

#1 : value2

EOB interrupt is enabled

End of enumeration elements list.


MARP

Margin Control Register PFLASH
address_offset : 0x1018 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

MARP MARP read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 MARGIN TRAPDIS

MARGIN : PFLASH Margin Selection
bits : 0 - 2 (3 bit)
access : read-write

Enumeration:

#0000 : value1

Standard (default) margin.

#0001 : value2

Tight margin for 0 (low) level. Suboptimal 0-bits are read as 1s.

#0100 : value3

Tight margin for 1 (high) level. Suboptimal 1-bits are read as 0s.

End of enumeration elements list.

TRAPDIS : PFLASH Double-Bit Error Trap Disable
bits : 15 - 14 (0 bit)
access : read-write

Enumeration:

#0 : value1

If a double-bit error occurs in PFLASH, a bus error trap is generated.

#1 : value2

The double-bit error trap is disabled. Shall be used only during margin check

End of enumeration elements list.


PROCON0

Flash Protection Configuration Register User 0
address_offset : 0x1020 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PROCON0 PROCON0 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 S0L S1L S2L S3L S4L S5L S6L S7L S8L S9L S10_S11L S12_S13L S14_S15L RPRO

S0L : Sector 0 Locked for Write Protection by User 0
bits : 0 - -1 (0 bit)
access : read-only

Enumeration:

#0 : value1

No write protection is configured for sector n.

#1 : value2

Write protection is configured for sector n.

End of enumeration elements list.

S1L : Sector 1 Locked for Write Protection by User 0
bits : 1 - 0 (0 bit)
access : read-only

Enumeration:

#0 : value1

No write protection is configured for sector n.

#1 : value2

Write protection is configured for sector n.

End of enumeration elements list.

S2L : Sector 2 Locked for Write Protection by User 0
bits : 2 - 1 (0 bit)
access : read-only

Enumeration:

#0 : value1

No write protection is configured for sector n.

#1 : value2

Write protection is configured for sector n.

End of enumeration elements list.

S3L : Sector 3 Locked for Write Protection by User 0
bits : 3 - 2 (0 bit)
access : read-only

Enumeration:

#0 : value1

No write protection is configured for sector n.

#1 : value2

Write protection is configured for sector n.

End of enumeration elements list.

S4L : Sector 4 Locked for Write Protection by User 0
bits : 4 - 3 (0 bit)
access : read-only

Enumeration:

#0 : value1

No write protection is configured for sector n.

#1 : value2

Write protection is configured for sector n.

End of enumeration elements list.

S5L : Sector 5 Locked for Write Protection by User 0
bits : 5 - 4 (0 bit)
access : read-only

Enumeration:

#0 : value1

No write protection is configured for sector n.

#1 : value2

Write protection is configured for sector n.

End of enumeration elements list.

S6L : Sector 6 Locked for Write Protection by User 0
bits : 6 - 5 (0 bit)
access : read-only

Enumeration:

#0 : value1

No write protection is configured for sector n.

#1 : value2

Write protection is configured for sector n.

End of enumeration elements list.

S7L : Sector 7 Locked for Write Protection by User 0
bits : 7 - 6 (0 bit)
access : read-only

Enumeration:

#0 : value1

No write protection is configured for sector n.

#1 : value2

Write protection is configured for sector n.

End of enumeration elements list.

S8L : Sector 8 Locked for Write Protection by User 0
bits : 8 - 7 (0 bit)
access : read-only

Enumeration:

#0 : value1

No write protection is configured for sector n.

#1 : value2

Write protection is configured for sector n.

End of enumeration elements list.

S9L : Sector 9 Locked for Write Protection by User 0
bits : 9 - 8 (0 bit)
access : read-only

Enumeration:

#0 : value1

No write protection is configured for sector n.

#1 : value2

Write protection is configured for sector n.

End of enumeration elements list.

S10_S11L : Sectors 10 and 11 Locked for Write Protection by User 0
bits : 10 - 9 (0 bit)
access : read-only

Enumeration:

#0 : value1

No write protection is configured for sectors 10+11.

#1 : value2

Write protection is configured for sectors 10+11.

End of enumeration elements list.

S12_S13L : Sectors 12 and 13 Locked for Write Protection by User 0
bits : 11 - 10 (0 bit)
access : read-only

Enumeration:

#0 : value1

No write protection is configured for sectors 12+13.

#1 : value2

Write protection is configured for sectors 12+13.

End of enumeration elements list.

S14_S15L : Sectors 14 and 15 Locked for Write Protection by User 0
bits : 12 - 11 (0 bit)
access : read-only

Enumeration:

#0 : value1

No write protection is configured for sectors 14+15.

#1 : value2

Write protection is configured for sectors 14+15.

End of enumeration elements list.

RPRO : Read Protection Configuration
bits : 15 - 14 (0 bit)
access : read-only

Enumeration:

#0 : value1

No read protection configured

#1 : value2

Read protection and global write protection is configured by user 0 (master user)

End of enumeration elements list.


PROCON1

Flash Protection Configuration Register User 1
address_offset : 0x1024 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PROCON1 PROCON1 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 S0L S1L S2L S3L S4L S5L S6L S7L S8L S9L S10_S11L S12_S13L S14_S15L PSR

S0L : Sector 0 Locked for Write Protection by User 1
bits : 0 - -1 (0 bit)
access : read-only

Enumeration:

#0 : value1

No write protection is configured for sector n.

#1 : value2

Write protection is configured for sector n.

End of enumeration elements list.

S1L : Sector 1 Locked for Write Protection by User 1
bits : 1 - 0 (0 bit)
access : read-only

Enumeration:

#0 : value1

No write protection is configured for sector n.

#1 : value2

Write protection is configured for sector n.

End of enumeration elements list.

S2L : Sector 2 Locked for Write Protection by User 1
bits : 2 - 1 (0 bit)
access : read-only

Enumeration:

#0 : value1

No write protection is configured for sector n.

#1 : value2

Write protection is configured for sector n.

End of enumeration elements list.

S3L : Sector 3 Locked for Write Protection by User 1
bits : 3 - 2 (0 bit)
access : read-only

Enumeration:

#0 : value1

No write protection is configured for sector n.

#1 : value2

Write protection is configured for sector n.

End of enumeration elements list.

S4L : Sector 4 Locked for Write Protection by User 1
bits : 4 - 3 (0 bit)
access : read-only

Enumeration:

#0 : value1

No write protection is configured for sector n.

#1 : value2

Write protection is configured for sector n.

End of enumeration elements list.

S5L : Sector 5 Locked for Write Protection by User 1
bits : 5 - 4 (0 bit)
access : read-only

Enumeration:

#0 : value1

No write protection is configured for sector n.

#1 : value2

Write protection is configured for sector n.

End of enumeration elements list.

S6L : Sector 6 Locked for Write Protection by User 1
bits : 6 - 5 (0 bit)
access : read-only

Enumeration:

#0 : value1

No write protection is configured for sector n.

#1 : value2

Write protection is configured for sector n.

End of enumeration elements list.

S7L : Sector 7 Locked for Write Protection by User 1
bits : 7 - 6 (0 bit)
access : read-only

Enumeration:

#0 : value1

No write protection is configured for sector n.

#1 : value2

Write protection is configured for sector n.

End of enumeration elements list.

S8L : Sector 8 Locked for Write Protection by User 1
bits : 8 - 7 (0 bit)
access : read-only

Enumeration:

#0 : value1

No write protection is configured for sector n.

#1 : value2

Write protection is configured for sector n.

End of enumeration elements list.

S9L : Sector 9 Locked for Write Protection by User 1
bits : 9 - 8 (0 bit)
access : read-only

Enumeration:

#0 : value1

No write protection is configured for sector n.

#1 : value2

Write protection is configured for sector n.

End of enumeration elements list.

S10_S11L : Sectors 10 and 11 Locked for Write Protection by User 1
bits : 10 - 9 (0 bit)
access : read-only

Enumeration:

#0 : value1

No write protection is configured for sectors 10+11.

#1 : value2

Write protection is configured for sectors 10+11.

End of enumeration elements list.

S12_S13L : Sectors 12 and 13 Locked for Write Protection by User 1
bits : 11 - 10 (0 bit)
access : read-only

Enumeration:

#0 : value1

No write protection is configured for sectors 12+13.

#1 : value2

Write protection is configured for sectors 12+13.

End of enumeration elements list.

S14_S15L : Sectors 14 and 15 Locked for Write Protection by User 1
bits : 12 - 11 (0 bit)
access : read-only

Enumeration:

#0 : value1

No write protection is configured for sectors 14+15.

#1 : value2

Write protection is configured for sectors 14+15.

End of enumeration elements list.

PSR : Physical Sector Repair
bits : 16 - 15 (0 bit)
access : read-only

Enumeration:

#0 : value1

Physical Sector Repair command disabled; Erase Physical Sector command sequence available.

#1 : value2

Physical Sector Repair command sequence enabled; Erase Physical Sector command sequence disabled.

End of enumeration elements list.


PROCON2

Flash Protection Configuration Register User 2
address_offset : 0x1028 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PROCON2 PROCON2 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 S0ROM S1ROM S2ROM S3ROM S4ROM S5ROM S6ROM S7ROM S8ROM S9ROM S10_S11ROM S12_S13ROM S14_S15ROM

S0ROM : Sector 0 Locked Forever by User 2
bits : 0 - -1 (0 bit)
access : read-only

Enumeration:

#0 : value1

No ROM functionality configured for sector n.

#1 : value2

ROM functionality is configured for sector n. Re-programming of this sector is no longer possible.

End of enumeration elements list.

S1ROM : Sector 1 Locked Forever by User 2
bits : 1 - 0 (0 bit)
access : read-only

Enumeration:

#0 : value1

No ROM functionality configured for sector n.

#1 : value2

ROM functionality is configured for sector n. Re-programming of this sector is no longer possible.

End of enumeration elements list.

S2ROM : Sector 2 Locked Forever by User 2
bits : 2 - 1 (0 bit)
access : read-only

Enumeration:

#0 : value1

No ROM functionality configured for sector n.

#1 : value2

ROM functionality is configured for sector n. Re-programming of this sector is no longer possible.

End of enumeration elements list.

S3ROM : Sector 3 Locked Forever by User 2
bits : 3 - 2 (0 bit)
access : read-only

Enumeration:

#0 : value1

No ROM functionality configured for sector n.

#1 : value2

ROM functionality is configured for sector n. Re-programming of this sector is no longer possible.

End of enumeration elements list.

S4ROM : Sector 4 Locked Forever by User 2
bits : 4 - 3 (0 bit)
access : read-only

Enumeration:

#0 : value1

No ROM functionality configured for sector n.

#1 : value2

ROM functionality is configured for sector n. Re-programming of this sector is no longer possible.

End of enumeration elements list.

S5ROM : Sector 5 Locked Forever by User 2
bits : 5 - 4 (0 bit)
access : read-only

Enumeration:

#0 : value1

No ROM functionality configured for sector n.

#1 : value2

ROM functionality is configured for sector n. Re-programming of this sector is no longer possible.

End of enumeration elements list.

S6ROM : Sector 6 Locked Forever by User 2
bits : 6 - 5 (0 bit)
access : read-only

Enumeration:

#0 : value1

No ROM functionality configured for sector n.

#1 : value2

ROM functionality is configured for sector n. Re-programming of this sector is no longer possible.

End of enumeration elements list.

S7ROM : Sector 7 Locked Forever by User 2
bits : 7 - 6 (0 bit)
access : read-only

Enumeration:

#0 : value1

No ROM functionality configured for sector n.

#1 : value2

ROM functionality is configured for sector n. Re-programming of this sector is no longer possible.

End of enumeration elements list.

S8ROM : Sector 8 Locked Forever by User 2
bits : 8 - 7 (0 bit)
access : read-only

Enumeration:

#0 : value1

No ROM functionality configured for sector n.

#1 : value2

ROM functionality is configured for sector n. Re-programming of this sector is no longer possible.

End of enumeration elements list.

S9ROM : Sector 9 Locked Forever by User 2
bits : 9 - 8 (0 bit)
access : read-only

Enumeration:

#0 : value1

No ROM functionality configured for sector n.

#1 : value2

ROM functionality is configured for sector n. Re-programming of this sector is no longer possible.

End of enumeration elements list.

S10_S11ROM : Sectors 10 and 11 Locked Forever by User 2
bits : 10 - 9 (0 bit)
access : read-only

Enumeration:

#0 : value1

No ROM functionality is configured for sectors 10+11.

#1 : value2

ROM functionality is configured for sectors 10+11.

End of enumeration elements list.

S12_S13ROM : Sectors 12 and 13 Locked Forever by User 2
bits : 11 - 10 (0 bit)
access : read-only

Enumeration:

#0 : value1

No ROM functionality is configured for sectors 12+13.

#1 : value2

ROM functionality is configured for sectors 12+13.

End of enumeration elements list.

S14_S15ROM : Sectors 14 and 15 Locked Forever by User 2
bits : 12 - 11 (0 bit)
access : read-only

Enumeration:

#0 : value1

No ROM functionality is configured for sectors 14+15.

#1 : value2

ROM functionality is configured for sectors 14+15.

End of enumeration elements list.



Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !

This website is sponsored by EmbeetleEmbeetle, an IDE designed from scratch for embedded software developers.