Embeetle, an IDE designed from scratch for embedded software developers.address_offset : 0x0 Bytes (0x0)
size : 0x2000 byte (0x0)
mem_usage : registers
protection : not protected
ADC2 Control and Status Register
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
VBAT_RANGE : ADC2 Channel 0 Range Selection
bits : 16 - 15 (0 bit)
access : read-write
Enumeration:
0b0 : Range1
Range from 3 to 22 V is selected
0b1 : Range2
Range from 3 to 28 V is selected
End of enumeration elements list.
VS_RANGE : ADC2 Channel 1 Range Selection
bits : 17 - 16 (0 bit)
access : read-write
Enumeration:
0b0 : Range1
Range from 3 to 22 V is selected
0b1 : Range2
Range from 3 to 28 V is selected
End of enumeration elements list.
Measurement Unit Control Register 1
address_offset : 0x14 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CALIB_EN : Calibration Enable for Channels 0 to 5
bits : 0 - 4 (5 bit)
access : read-write
Enumeration:
0b000001 : CH0_EN
Channel 0 calibration enable
0b000010 : CH1_EN
Channel 1 calibration enable
0b000100 : CH2_EN
Channel 2 calibration enable
0b001000 : CH3_EN
Channel 3 calibration enable
0b010000 : CH4_EN
Channel 4 calibration enable
0b100000 : CH5_EN
Channel 5 calibration enable
End of enumeration elements list.
Measurement Unit Control Register 2
address_offset : 0x18 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MCM_PD_N : Power Down Signal for MCM
bits : 0 - -1 (0 bit)
access : read-write
Enumeration:
0b0 : MCM_Disabled
Measurement Core Module Disabled
0b1 : MCM_Enabled
Measurement Core Module Enabled
End of enumeration elements list.
TS_SD_SEL_CONF : Temperature Sensor Control Configuration
bits : 1 - 0 (0 bit)
access : read-write
Enumeration:
0b0 : Constant
Temperature Sensor selection done by bitfield TSENSE_SD_SEL
0b1 : Not_Active
Temperature Sensor selection done by DPP
End of enumeration elements list.
TSENSE_SD_SEL : Temperature Sensor selection connected to Ch9
bits : 2 - 1 (0 bit)
access : read-write
Enumeration:
0b0 : PMU_TSENSE
PMU Temperature sensor selected
0b1 : Central_TSENSE
Central Temperature Sensor selected
End of enumeration elements list.
MCM_RDY : Ready Signal for MCM after Power On or Reset
bits : 7 - 6 (0 bit)
access : read-only
Enumeration:
0b0 : MCM_Not_Ready
Measurement Core Module in startup phase
0b1 : MCM_Ready
Measurement Core Module start-up phase finished
End of enumeration elements list.
SAMPLE_TIME_int : Sample time of ADC2
bits : 8 - 10 (3 bit)
access : read-write
Enumeration:
0x0 : MICLK4
4 MI_CLK clock periods
0x1 : MICLK6
6 MI_CLK clock periods
0x2 : MICLK8
8 MI_CLK clock periods
0x3 : MICLK10
10 MI_CLK clock periods
0x4 : MICLK12
12 MI_CLK clock periods (default)
0x5 : MICLK14
14 MI_CLK clock periods
0x6 : MICLK16
16 MI_CLK clock periods
0x7 : MICLK18
18 MI_CLK clock periods
0x8 : MICLK20
20 MI_CLK clock periods
0x9 : MICLK22
22 MI_CLK clock periods
End of enumeration elements list.
SEL_TS_COUNT : Time for automatic multiplexing of temperature sensor
bits : 16 - 18 (3 bit)
access : read-write
Enumeration:
0x0 : 1SEQ
1 sequence
0x1 : 2SEQ
2 sequences
0x2 : 3SEQ
3 sequences
0x3 : 4SEQ
4 sequences
0x4 : 5SEQ
5 sequences
0x5 : 6SEQ
6 sequences
0x6 : 7SEQ
7 sequences
0x7 : 8SEQ
8 sequences
0x8 : 9SEQ
9 sequences
0x9 : 10SEQ
10 sequences
0xA : 11SEQ
11 sequences
0xB : 12SEQ
12 sequences
0xC : 13SEQ
13 sequences
0xD : 14SEQ
14 sequences
0xE : 15SEQ
15 sequences
0xF : 16SEQ
16 sequences
End of enumeration elements list.
Measurement Unit Control Register 4
address_offset : 0x1C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FILT_OUT_SEL_5_0 : Output Filter Selection for Channels 0 to 5
bits : 0 - 4 (5 bit)
access : read-write
FILT_OUT_SEL_9_6 : Output Filter Selection for Channels 6 to 9
bits : 8 - 10 (3 bit)
access : read-write
Measurement Channel Enable Bits for Cycle 1-4
address_offset : 0x20 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SQ1 : Sequence 1 channel enable
bits : 0 - 4 (5 bit)
access : read-write
SQ2 : Sequence 2 channel enable
bits : 8 - 12 (5 bit)
access : read-write
SQ3 : Sequence 3 channel enable
bits : 16 - 20 (5 bit)
access : read-write
SQ4 : Sequence 4 channel enable
bits : 24 - 28 (5 bit)
access : read-write
Measurement Channel Enable Bits for Cycle 5 - 8
address_offset : 0x24 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SQ5 : Sequence 5 channel enable
bits : 0 - 4 (5 bit)
access : read-write
SQ6 : Sequence 6 channel enable
bits : 8 - 12 (5 bit)
access : read-write
SQ7 : Sequence 7 channel enable
bits : 16 - 20 (5 bit)
access : read-write
SQ8 : Sequence 8 channel enable
bits : 24 - 28 (5 bit)
access : read-write
Measurement Channel Enable Bits for Cycle 9 - 10
address_offset : 0x28 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SQ9 : Sequence 9 channel enable
bits : 0 - 4 (5 bit)
access : read-write
SQ10 : Sequence 10 channel enable
bits : 8 - 12 (5 bit)
access : read-write
Measurement Channel Enable Bits for Cycle 1 - 8
address_offset : 0x2C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SQ1_int : Sequence 1 channel enable
bits : 0 - 2 (3 bit)
access : read-only
SQ2_int : Sequence 2 channel enable
bits : 4 - 6 (3 bit)
access : read-only
SQ3_int : Sequence 3 channel enable
bits : 8 - 10 (3 bit)
access : read-only
SQ4_int : Sequence 4 channel enable
bits : 12 - 14 (3 bit)
access : read-only
SQ5_int : Sequence 5 channel enable
bits : 16 - 18 (3 bit)
access : read-only
SQ6_int : Sequence 6 channel enable
bits : 20 - 22 (3 bit)
access : read-only
SQ7_int : Sequence 7 channel enable
bits : 24 - 26 (3 bit)
access : read-only
SQ8_int : Sequence 8 channel enable
bits : 28 - 30 (3 bit)
access : read-only
Measurement Channel Enable Bits for Cycle 9 and 10
address_offset : 0x30 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SQ9_int : Sequence 9 channel enable
bits : 0 - 2 (3 bit)
access : read-only
SQ10_int : Sequence 10 channel enable
bits : 4 - 6 (3 bit)
access : read-only
Calibration for Channel 0 and 1
address_offset : 0x34 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OFFS_CH0 : Offset Calibration for channel 0
bits : 0 - 6 (7 bit)
access : read-write
GAIN_CH0 : Gain Calibration for channel 0
bits : 8 - 14 (7 bit)
access : read-write
OFFS_CH1 : Offset Calibration for channel 1
bits : 16 - 22 (7 bit)
access : read-write
GAIN_CH1 : Gain Calibration for channel 1
bits : 24 - 30 (7 bit)
access : read-write
Calibration for Channel 2 and 3
address_offset : 0x38 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OFFS_CH2 : Offset Calibration for channel 2
bits : 0 - 6 (7 bit)
access : read-write
GAIN_CH2 : Gain Calibration for channel 2
bits : 8 - 14 (7 bit)
access : read-write
OFFS_CH3 : Offset Calibration for channel 3
bits : 16 - 22 (7 bit)
access : read-write
GAIN_CH3 : Gain Calibration for channel 3
bits : 24 - 30 (7 bit)
access : read-write
Calibration for Channel 4 and 5
address_offset : 0x3C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OFFS_CH4 : Offset Calibration for channel 4
bits : 0 - 6 (7 bit)
access : read-write
GAIN_CH4 : Gain Calibration for channel 4
bits : 8 - 14 (7 bit)
access : read-write
OFFS_CH5 : Offset Calibration for channel 5
bits : 16 - 22 (7 bit)
access : read-write
GAIN_CH5 : Gain Calibration for channel 5
bits : 24 - 30 (7 bit)
access : read-write
Sequencer Feedback Register
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SQ_FB : Current Sequence that caused software mode
bits : 0 - 2 (3 bit)
access : read-only
Enumeration:
0b0000 : SQ1
Sequence 1
0b0001 : SQ2
Sequence 2
0b0010 : SQ3
Sequence 3
0b0011 : SQ4
Sequence 4
0b0100 : SQ5
Sequence 5
0b0101 : SQ6
Sequence 6
0b0110 : SQ7
Sequence 7
0b0111 : SQ8
Sequence 8
0b1000 : SQ9
Sequence 9
0b1001 : SQ10
Sequence 10
0b1010 : ESM
Exceptional Sequencer Mode
0b1011 : CH_MASK
Channel Mask = 0
0b1100 : SUSPEND
Debug Suspend Mode
End of enumeration elements list.
SQ_STOP : ADC2 Sequencer Stop Signal for DPP
bits : 8 - 7 (0 bit)
access : read-only
Enumeration:
0b0 : DPP_Running
Postprocessing Sequencer in running mode
0b1 : DPP_Stopped
Postprocessing Sequencer stopped / Software Mode entered
End of enumeration elements list.
EIM_ACTIVE : ADC2 EIM active
bits : 9 - 8 (0 bit)
access : read-only
Enumeration:
0b0 : not_active
EIM not active
0b1 : active
EIM active
End of enumeration elements list.
ESM_ACTIVE : ADC2 ESM active
bits : 10 - 9 (0 bit)
access : read-only
Enumeration:
0b0 : not_active
ESM not active
0b1 : active
ESM active
End of enumeration elements list.
SQx : Current Active Sequencer
bits : 11 - 13 (3 bit)
access : read-only
Enumeration:
0b0000 : SQ0
Sequence 0 enable
0b0001 : SQ1
Sequence 1 enable
0b0010 : SQ2
Sequence 2 enable
0b0011 : SQ3
Sequence 3 enable
0b0100 : SQ4
Sequence 4 enable
0b0101 : SQ5
Sequence 5 enable
0b0110 : SQ6
Sequence 6 enable
0b0111 : SQ7
Sequence 7 enable
0b1000 : SQ8
Sequence 8 enable
0b1001 : SQ9
Sequence 9 enable
End of enumeration elements list.
CHx : Current ADC2 Channel
bits : 16 - 19 (4 bit)
access : read-only
Enumeration:
0b00000 : CH0
Channel 0 enable
0b00001 : CH1
Channel 1 enable
0b00010 : CH2
Channel 2 enable
0b00011 : CH3
Channel 3 enable
0b00100 : CH4
Channel 4 enable
0b00101 : CH5
Channel 5 enable
0b00110 : CH6
Channel 6 enable
0b11101 : CH7
Channel 7 enable
0b11110 : CH8
Channel 8 enable
0b11111 : CH9
Channel 9 enable
End of enumeration elements list.
Calibration for Channel 6 and 7
address_offset : 0x40 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OFFS_CH6 : Offset Calibration for channel 6
bits : 0 - 6 (7 bit)
access : read-only
GAIN_CH6 : Gain Calibration for channel 6
bits : 8 - 14 (7 bit)
access : read-only
OFFS_CH7 : Offset Calibration for channel 7
bits : 16 - 22 (7 bit)
access : read-only
GAIN_CH7 : Gain Calibration for channel 7
bits : 24 - 30 (7 bit)
access : read-only
Calibration for Channel 8 and 9
address_offset : 0x44 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OFFS_CH8 : Offset Calibration for channel 8
bits : 0 - 6 (7 bit)
access : read-only
GAIN_CH8 : Gain Calibration for channel 8
bits : 8 - 14 (7 bit)
access : read-only
OFFS_CH9 : Offset Calibration for channel 9
bits : 16 - 22 (7 bit)
access : read-only
GAIN_CH9 : Gain Calibration for channel 9
bits : 24 - 30 (7 bit)
access : read-only
Filter Coefficients ADC Channel 0-5
address_offset : 0x48 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CH0 : Filter Coefficients ADC channel 0
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
0b00 : value0
1/2 weight of current sample
0b01 : value1
1/4 weight of current sample
0b10 : value2
1/8 weight of current sample
0b11 : value3
1/16 weight of current sample
End of enumeration elements list.
CH1 : Filter Coefficients ADC channel 1
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
0b00 : value0
1/2 weight of current sample
0b01 : value1
1/4 weight of current sample
0b10 : value2
1/8 weight of current sample
0b11 : value3
1/16 weight of current sample
End of enumeration elements list.
CH2 : Filter Coefficients ADC channel 2
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
0b00 : value0
1/2 weight of current sample
0b01 : value1
1/4 weight of current sample
0b10 : value2
1/8 weight of current sample
0b11 : value3
1/16 weight of current sample
End of enumeration elements list.
CH3 : Filter Coefficients ADC channel 3
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
0b00 : value0
1/2 weight of current sample
0b01 : value1
1/4 weight of current sample
0b10 : value2
1/8 weight of current sample
0b11 : value3
1/16 weight of current sample
End of enumeration elements list.
CH4 : Filter Coefficients ADC channel 4
bits : 8 - 8 (1 bit)
access : read-write
Enumeration:
0b00 : value0
1/2 weight of current sample
0b01 : value1
1/4 weight of current sample
0b10 : value2
1/8 weight of current sample
0b11 : value3
1/16 weight of current sample
End of enumeration elements list.
CH5 : Filter Coefficients ADC channel 5
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
0b00 : value0
1/2 weight of current sample
0b01 : value1
1/4 weight of current sample
0b10 : value2
1/8 weight of current sample
0b11 : value3
1/16 weight of current sample
End of enumeration elements list.
Filter Coefficents ADC Channel 6-9
address_offset : 0x4C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CH6 : Filter Coefficients ADC channel 6
bits : 0 - 0 (1 bit)
access : read-only
Enumeration:
0b00 : value0
1/2 weight of current sample
0b01 : value1
1/4 weight of current sample
0b10 : value2
1/8 weight of current sample
0b11 : value3
1/16 weight of current sample
End of enumeration elements list.
CH7 : Filter Coefficients ADC channel 7
bits : 2 - 2 (1 bit)
access : read-only
Enumeration:
0b00 : value0
1/2 weight of current sample
0b01 : value1
1/4 weight of current sample
0b10 : value2
1/8 weight of current sample
0b11 : value3
1/16 weight of current sample
End of enumeration elements list.
CH8 : Filter Coefficients ADC channel 8
bits : 4 - 4 (1 bit)
access : read-only
Enumeration:
0b00 : value0
1/2 weight of current sample
0b01 : value1
1/4 weight of current sample
0b10 : value2
1/8 weight of current sample
0b11 : value3
1/16 weight of current sample
End of enumeration elements list.
CH9 : Filter Coefficients ADC channel 9
bits : 6 - 6 (1 bit)
access : read-only
Enumeration:
0b00 : value0
1/2 weight of current sample
0b01 : value1
1/4 weight of current sample
0b10 : value2
1/8 weight of current sample
0b11 : value3
1/16 weight of current sample
End of enumeration elements list.
ADC or Filter Output Channel 0
address_offset : 0x50 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OUT_CH0 : ADC or filter output value channel 0
bits : 0 - 8 (9 bit)
access : read-only
ADC or Filter Output Channel 1
address_offset : 0x54 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OUT_CH1 : ADC or filter output value channel 1
bits : 0 - 8 (9 bit)
access : read-only
ADC or Filter Output Channel 2
address_offset : 0x58 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OUT_CH2 : ADC or filter output value channel 2
bits : 0 - 8 (9 bit)
access : read-only
ADC or Filter Output Channel 3
address_offset : 0x5C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OUT_CH3 : ADC or filter output value channel 3
bits : 0 - 8 (9 bit)
access : read-only
ADC or Filter Output Channel 4
address_offset : 0x60 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OUT_CH4 : ADC or filter output value channel 4
bits : 0 - 8 (9 bit)
access : read-only
ADC or Filter Output Channel 5
address_offset : 0x64 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OUT_CH5 : ADC or filter output value channel 5
bits : 0 - 8 (9 bit)
access : read-only
ADC or Filter Output Channel 6
address_offset : 0x68 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OUT_CH6 : ADC or filter output value channel 6
bits : 0 - 8 (9 bit)
access : read-only
ADC or Filter Output Channel 7
address_offset : 0x6C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OUT_CH7 : ADC or filter output value channel 7
bits : 0 - 8 (9 bit)
access : read-only
ADC or Filter Output Channel 8
address_offset : 0x70 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OUT_CH8 : ADC or filter output value channel 8
bits : 0 - 8 (9 bit)
access : read-only
ADC or Filter Output Channel 9
address_offset : 0x74 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OUT_CH9 : ADC or filter output value channel 9
bits : 0 - 8 (9 bit)
access : read-only
Upper Threshold Filter Enable
address_offset : 0x78 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
Ch0_EN : Upper threshold IIR filter enable ch 0
bits : 0 - -1 (0 bit)
access : read-write
Enumeration:
0b0 : value1
disable
0b1 : value2
enable
End of enumeration elements list.
Ch1_EN : Upper threshold IIR filter enable ch 1
bits : 1 - 0 (0 bit)
access : read-write
Enumeration:
0b0 : value1
disable
0b1 : value2
enable
End of enumeration elements list.
Ch2_EN : Upper threshold IIR filter enable ch 2
bits : 2 - 1 (0 bit)
access : read-write
Enumeration:
0b0 : value1
disable
0b1 : value2
enable
End of enumeration elements list.
Ch3_EN : Upper threshold IIR filter enable ch 3
bits : 3 - 2 (0 bit)
access : read-write
Enumeration:
0b0 : value1
disable
0b1 : value2
enable
End of enumeration elements list.
Ch4_EN : Upper threshold IIR filter enable ch 4
bits : 4 - 3 (0 bit)
access : read-write
Enumeration:
0b0 : value1
disable
0b1 : value2
enable
End of enumeration elements list.
Ch5_EN : Upper threshold IIR filter enable ch 5
bits : 5 - 4 (0 bit)
access : read-write
Enumeration:
0b0 : value1
disable
0b1 : value2
enable
End of enumeration elements list.
Lower Threshold Filter Enable
address_offset : 0x7C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
Ch0_EN : Lower threshold IIR filter enable ch 0
bits : 0 - -1 (0 bit)
access : read-write
Enumeration:
0b0 : value1
disable
0b1 : value2
enable
End of enumeration elements list.
Ch1_EN : Lower threshold IIR filter enable ch 1
bits : 1 - 0 (0 bit)
access : read-write
Enumeration:
0b0 : value1
disable
0b1 : value2
enable
End of enumeration elements list.
Ch2_EN : Lower threshold IIR filter enable ch 2
bits : 2 - 1 (0 bit)
access : read-write
Enumeration:
0b0 : value1
disable
0b1 : value2
enable
End of enumeration elements list.
Ch3_EN : Lower threshold IIR filter enable ch 3
bits : 3 - 2 (0 bit)
access : read-write
Enumeration:
0b0 : value1
disable
0b1 : value2
enable
End of enumeration elements list.
Ch4_EN : Lower threshold IIR filter enable ch 4
bits : 4 - 3 (0 bit)
access : read-write
Enumeration:
0b0 : value1
disable
0b1 : value2
enable
End of enumeration elements list.
Ch5_EN : Lower threshold IIR filter enable ch 5
bits : 5 - 4 (0 bit)
access : read-write
Enumeration:
0b0 : value1
disable
0b1 : value2
enable
End of enumeration elements list.
Channel Settings Bits for Exceptional Interrupt Measurement
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CHx : Channel set for exceptional interrupt measurement (EIM)
bits : 0 - 3 (4 bit)
access : read-write
Enumeration:
0b00000 : CH0_EN
Channel 0 enable
0b00001 : CH1_EN
Channel 1 enable
0b00010 : CH2_EN
Channel 2 enable
0b00011 : CH3_EN
Channel 3 enable
0b00100 : CH4_EN
Channel 4 enable
0b00101 : CH5_EN
Channel 5 enable
0b00110 : CH6_EN
Channel 6 enable
0b11101 : CH7_EN
Channel 7 enable
0b11110 : CH8_EN
Channel 8 enable
0b11111 : CH9_EN
Channel 9 enable
End of enumeration elements list.
REP : Repeat count for exceptional interrupt measurement (EIM)
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
0b000 : 1
Measurements
0b001 : 2
Measurements
0b010 : 4
Measurements
0b011 : 8
Measurements
0b100 : 16
Measurements
0b101 : 32
Measurements
0b110 : 64
Measurements
0b111 : 128
Measurements
End of enumeration elements list.
EN : Exceptional interrupt measurement (EIM) Trigger Event enable
bits : 11 - 10 (0 bit)
access : read-write
Enumeration:
0b0 : DISABLE
start of EIM disabled
0b1 : ENABLE
start of IEM enabled
End of enumeration elements list.
SEL : Exceptional interrupt measurement (EIM) Trigger Trigger select
bits : 12 - 11 (0 bit)
access : read-write
Enumeration:
0b0 : CCU6_SEL
ccu6_int triggers EIM
0b1 : CP_SEL
cp_clk triggers EIM
End of enumeration elements list.
Lower Comparator Trigger Level Channel 0 -3
address_offset : 0x80 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CH0 : Channel 0 lower trigger level
bits : 0 - 6 (7 bit)
access : read-write
CH1 : Channel 1 lower trigger level
bits : 8 - 14 (7 bit)
access : read-write
CH2 : Channel 2 lower trigger level
bits : 16 - 22 (7 bit)
access : read-write
CH3 : Channel 3 lower trigger level
bits : 24 - 30 (7 bit)
Lower Comparator Trigger Level Channel 4 and 5
address_offset : 0x84 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CH4 : Channel 4 lower trigger level
bits : 0 - 6 (7 bit)
access : read-write
CH5 : Channel 5 lower trigger level
bits : 8 - 14 (7 bit)
access : read-write
Lower Comparator Trigger Level Channel 6 -9
address_offset : 0x88 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CH6 : Channel 6 lower trigger level
bits : 0 - 6 (7 bit)
access : read-write
CH7 : Channel 7 lower trigger level
bits : 8 - 14 (7 bit)
access : read-only
CH8 : Channel 8 lower trigger level
bits : 16 - 22 (7 bit)
access : read-write
CH9 : Channel 9 lower trigger level
bits : 24 - 30 (7 bit)
access : read-write
Upper Comparator Trigger Level Channel 0-3
address_offset : 0x8C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CH0 : Channel 0 upper trigger level
bits : 0 - 6 (7 bit)
access : read-write
CH1 : Channel 1 upper trigger level
bits : 8 - 14 (7 bit)
access : read-write
CH2 : Channel 2 upper trigger level
bits : 16 - 22 (7 bit)
access : read-write
CH3 : Channel 3 upper trigger level
bits : 24 - 30 (7 bit)
access : read-write
Upper Comparator Trigger Level Channel 4 -5
address_offset : 0x90 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CH4 : Channel 4 upper trigger level
bits : 0 - 6 (7 bit)
access : read-write
CH5 : Channel 5 upper trigger level
bits : 8 - 14 (7 bit)
access : read-write
Upper Comparator Trigger Level Channel 6 -9
address_offset : 0x94 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CH6 : Channel 6 upper trigger level
bits : 0 - 6 (7 bit)
access : read-only
CH7 : Channel 7 upper trigger level
bits : 8 - 14 (7 bit)
access : read-only
CH8 : Channel 8 upper trigger level
bits : 16 - 22 (7 bit)
access : read-only
CH9 : Channel 9 upper trigger level
bits : 24 - 30 (7 bit)
access : read-only
Lower Counter Trigger Level Channel 0 - 3
address_offset : 0x98 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CNT_LO_CH0 : Lower timer trigger threshold channel 0
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
0x0 : value1
1 measurement
0x1 : value2
2 measurements
0x2 : value3
4 measurements
0x3 : value4
8 measurements
0x4 : value5
16 measurements
0x5 : value6
32 measurements
0x6 : value7
64 measurements
0x7 : value8
128 measurements
End of enumeration elements list.
HYST_LO_CH0 : Channel 0 lower hysteresis
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
0x0 : HYSTOFF
hysteresis switched off
0x1 : HYST4
hysteresis = 4
0x2 : HYST8
hysteresis = 8
0x3 : HYST16
hysteresis = 16
End of enumeration elements list.
CNT_LO_CH1 : Lower timer trigger threshold channel 1
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
0x0 : value1
1 measurement
0x1 : value2
2 measurements
0x2 : value3
4 measurements
0x3 : value4
8 measurements
0x4 : value5
16 measurements
0x5 : value6
32 measurements
0x6 : value7
64 measurements
0x7 : value8
128 measurements
End of enumeration elements list.
HYST_LO_CH1 : Channel 1 lower hysteresis
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
0x0 : HYSTOFF
hysteresis switched off
0x1 : HYST4
hysteresis = 4
0x2 : HYST8
hysteresis = 8
0x3 : HYST16
hysteresis = 16
End of enumeration elements list.
CNT_LO_CH2 : Lower timer trigger threshold channel 2
bits : 16 - 17 (2 bit)
access : read-write
Enumeration:
0x0 : value1
1 measurement
0x1 : value2
2 measurements
0x2 : value3
4 measurements
0x3 : value4
8 measurements
0x4 : value5
16 measurements
0x5 : value6
32 measurements
0x6 : value7
64 measurements
0x7 : value8
128 measurements
End of enumeration elements list.
HYST_LO_CH2 : Channel 2 lower hysteresis
bits : 19 - 19 (1 bit)
access : read-write
Enumeration:
0x0 : HYSTOFF
hysteresis switched off
0x1 : HYST4
hysteresis = 4
0x2 : HYST8
hysteresis = 8
0x3 : HYST16
hysteresis = 16
End of enumeration elements list.
CNT_LO_CH3 : Lower timer trigger threshold channel 3
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
0x0 : value1
1 measurement
0x1 : value2
2 measurements
0x2 : value3
4 measurements
0x3 : value4
8 measurements
0x4 : value5
16 measurements
0x5 : value6
32 measurements
0x6 : value7
64 measurements
0x7 : value8
128 measurements
End of enumeration elements list.
HYST_LO_CH3 : Channel 3 lower hysteresis
bits : 27 - 27 (1 bit)
access : read-write
Enumeration:
0x0 : HYSTOFF
hysteresis switched off
0x1 : HYST4
hysteresis = 4
0x2 : HYST8
hysteresis = 8
0x3 : HYST16
hysteresis = 16
End of enumeration elements list.
Lower Counter Trigger Level Channel 4 and 5
address_offset : 0x9C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CNT_LO_CH4 : Lower timer trigger threshold channel 4
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
0x0 : value1
1 measurement
0x1 : value2
2 measurements
0x2 : value3
4 measurements
0x3 : value4
8 measurements
0x4 : value5
16 measurements
0x5 : value6
32 measurements
0x6 : value7
64 measurements
0x7 : value8
128 measurements
End of enumeration elements list.
HYST_LO_CH4 : Channel 4 lower hysteresis
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
0x0 : HYSTOFF
hysteresis switched off
0x1 : HYST4
hysteresis = 4
0x2 : HYST8
hysteresis = 8
0x3 : HYST16
hysteresis = 16
End of enumeration elements list.
CNT_LO_CH5 : Lower timer trigger threshold channel 5
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
0x0 : value1
1 measurement
0x1 : value2
2 measurements
0x2 : value3
4 measurements
0x3 : value4
8 measurements
0x4 : value5
16 measurements
0x5 : value6
32 measurements
0x6 : value7
64 measurements
0x7 : value8
128 measurements
End of enumeration elements list.
HYST_LO_CH5 : Channel 5 lower hysteresis
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
0x0 : HYSTOFF
hysteresis switched off
0x1 : HYST4
hysteresis = 4
0x2 : HYST8
hysteresis = 8
0x3 : HYST16
hysteresis = 16
End of enumeration elements list.
Lower Counter Trigger Level Channel 6 - 9
address_offset : 0xA0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CNT_LO_CH6 : Lower timer trigger threshold channel 6
bits : 0 - 1 (2 bit)
access : read-only
Enumeration:
0x0 : value1
1 measurement
0x1 : value2
2 measurements
0x2 : value3
4 measurements
0x3 : value4
8 measurements
0x4 : value5
16 measurements
0x5 : value6
32 measurements
0x6 : value7
64 measurements
0x7 : value8
128 measurements
End of enumeration elements list.
HYST_LO_CH6 : Channel 6 lower hysteresis
bits : 3 - 3 (1 bit)
access : read-only
Enumeration:
0x0 : HYSTOFF
hysteresis switched off
0x1 : HYST4
hysteresis = 4
0x2 : HYST8
hysteresis = 8
0x3 : HYST16
hysteresis = 16
End of enumeration elements list.
CNT_LO_CH7 : Lower timer trigger threshold channel 7
bits : 8 - 9 (2 bit)
access : read-only
Enumeration:
0x0 : value1
1 measurement
0x1 : value2
2 measurements
0x2 : value3
4 measurements
0x3 : value4
8 measurements
0x4 : value5
16 measurements
0x5 : value6
32 measurements
0x6 : value7
64 measurements
0x7 : value8
128 measurements
End of enumeration elements list.
HYST_LO_CH7 : Channel 7 lower hysteresis
bits : 11 - 11 (1 bit)
access : read-only
Enumeration:
0x0 : HYSTOFF
hysteresis switched off
0x1 : HYST4
hysteresis = 4
0x2 : HYST8
hysteresis = 8
0x3 : HYST16
hysteresis = 16
End of enumeration elements list.
CNT_LO_CH8 : Lower timer trigger threshold channel 8
bits : 16 - 17 (2 bit)
access : read-only
Enumeration:
0x0 : value1
1 measurement
0x1 : value2
2 measurements
0x2 : value3
4 measurements
0x3 : value4
8 measurements
0x4 : value5
16 measurements
0x5 : value6
32 measurements
0x6 : value7
64 measurements
0x7 : value8
128 measurements
End of enumeration elements list.
HYST_LO_CH8 : Channel 8 lower hysteresis
bits : 19 - 19 (1 bit)
access : read-only
Enumeration:
0x0 : HYSTOFF
hysteresis switched off
0x1 : HYST4
hysteresis = 4
0x2 : HYST8
hysteresis = 8
0x3 : HYST16
hysteresis = 16
End of enumeration elements list.
CNT_LO_CH9 : Lower timer trigger threshold channel 9
bits : 24 - 25 (2 bit)
access : read-only
Enumeration:
0x0 : value1
1 measurement
0x1 : value2
2 measurements
0x2 : value3
4 measurements
0x3 : value4
8 measurements
0x4 : value5
16 measurements
0x5 : value6
32 measurements
0x6 : value7
64 measurements
0x7 : value8
128 measurements
End of enumeration elements list.
HYST_LO_CH9 : Channel 9 lower hysteresis
bits : 27 - 27 (1 bit)
access : read-only
Enumeration:
0x0 : HYSTOFF
hysteresis switched off
0x1 : HYST4
hysteresis = 4
0x2 : HYST8
hysteresis = 8
0x3 : HYST16
hysteresis = 16
End of enumeration elements list.
Upper Counter Trigger Level Channel 0 - 3
address_offset : 0xA4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CNT_UP_CH0 : Upper timer trigger threshold channel 0
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
0x0 : value1
1 measurement
0x1 : value2
2 measurements
0x2 : value3
4 measurements
0x3 : value4
8 measurements
0x4 : value5
16 measurements
0x5 : value6
32 measurements
0x6 : value7
64 measurements
0x7 : value8
128 measurements
End of enumeration elements list.
HYST_UP_CH0 : Channel 0 upper hysteresis
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
0x0 : HYSTOFF
hysteresis switched off
0x1 : HYST4
hysteresis = 4
0x2 : HYST8
hysteresis = 8
0x3 : HYST16
hysteresis = 16
End of enumeration elements list.
CNT_UP_CH1 : Upper timer trigger threshold channel 1
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
0x0 : value1
1 measurement
0x1 : value2
2 measurements
0x2 : value3
4 measurements
0x3 : value4
8 measurements
0x4 : value5
16 measurements
0x5 : value6
32 measurements
0x6 : value7
64 measurements
0x7 : value8
128 measurements
End of enumeration elements list.
HYST_UP_CH1 : Channel 1 upper hysteresis
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
0x0 : HYSTOFF
hysteresis switched off
0x1 : HYST4
hysteresis = 4
0x2 : HYST8
hysteresis = 8
0x3 : HYST16
hysteresis = 16
End of enumeration elements list.
CNT_UP_CH2 : Upper timer trigger threshold channel 2
bits : 16 - 17 (2 bit)
access : read-write
Enumeration:
0x0 : value1
1 measurement
0x1 : value2
2 measurements
0x2 : value3
4 measurements
0x3 : value4
8 measurements
0x4 : value5
16 measurements
0x5 : value6
32 measurements
0x6 : value7
64 measurements
0x7 : value8
128 measurements
End of enumeration elements list.
HYST_UP_CH2 : Channel 2 upper hysteresis
bits : 19 - 19 (1 bit)
access : read-write
Enumeration:
0x0 : HYSTOFF
hysteresis switched off
0x1 : HYST4
hysteresis = 4
0x2 : HYST8
hysteresis = 8
0x3 : HYST16
hysteresis = 16
End of enumeration elements list.
CNT_UP_CH3 : Upper timer trigger threshold channel 3
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
0x0 : value1
1 measurement
0x1 : value2
2 measurements
0x2 : value3
4 measurements
0x3 : value4
8 measurements
0x4 : value5
16 measurements
0x5 : value6
32 measurements
0x6 : value7
64 measurements
0x7 : value8
128 measurements
End of enumeration elements list.
HYST_UP_CH3 : Channel 3 upper hysteresis
bits : 27 - 27 (1 bit)
access : read-write
Enumeration:
0x0 : HYSTOFF
hysteresis switched off
0x1 : HYST4
hysteresis = 4
0x2 : HYST8
hysteresis = 8
0x3 : HYST16
hysteresis = 16
End of enumeration elements list.
Upper Counter Trigger Level Channel 4 and 5
address_offset : 0xA8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CNT_UP_CH4 : Upper timer trigger threshold channel 4
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
0x0 : value1
1 measurement
0x1 : value2
2 measurements
0x2 : value3
4 measurements
0x3 : value4
8 measurements
0x4 : value5
16 measurements
0x5 : value6
32 measurements
0x6 : value7
64 measurements
0x7 : value8
128 measurements
End of enumeration elements list.
HYST_UP_CH4 : Channel 4 upper hysteresis
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
0x0 : HYSTOFF
hysteresis switched off
0x1 : HYST4
hysteresis = 4
0x2 : HYST8
hysteresis = 8
0x3 : HYST16
hysteresis = 16
End of enumeration elements list.
CNT_UP_CH5 : Upper timer trigger threshold channel 5
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
0x0 : value1
1 measurement
0x1 : value2
2 measurements
0x2 : value3
4 measurements
0x3 : value4
8 measurements
0x4 : value5
16 measurements
0x5 : value6
32 measurements
0x6 : value7
64 measurements
0x7 : value8
128 measurements
End of enumeration elements list.
HYST_UP_CH5 : Channel 5 upper hysteresis
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
0x0 : HYSTOFF
hysteresis switched off
0x1 : HYST4
hysteresis = 4
0x2 : HYST8
hysteresis = 8
0x3 : HYST16
hysteresis = 16
End of enumeration elements list.
Upper Counter Trigger Level Channel 6 -9
address_offset : 0xAC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CNT_UP_CH6 : Upper timer trigger threshold channel 6
bits : 0 - 1 (2 bit)
access : read-only
Enumeration:
0x0 : value1
1 measurement
0x1 : value2
2 measurements
0x2 : value3
4 measurements
0x3 : value4
8 measurements
0x4 : value5
16 measurements
0x5 : value6
32 measurements
0x6 : value7
64 measurements
0x7 : value8
128 measurements
End of enumeration elements list.
HYST_UP_CH6 : Channel 6 upper hysteresis
bits : 3 - 3 (1 bit)
access : read-only
Enumeration:
0x0 : HYSTOFF
hysteresis switched off
0x1 : HYST4
hysteresis = 4
0x2 : HYST8
hysteresis = 8
0x3 : HYST16
hysteresis = 16
End of enumeration elements list.
CNT_UP_CH7 : Upper timer trigger threshold channel 7
bits : 8 - 9 (2 bit)
access : read-only
Enumeration:
0x0 : value1
1 measurement
0x1 : value2
2 measurements
0x2 : value3
4 measurements
0x3 : value4
8 measurements
0x4 : value5
16 measurements
0x5 : value6
32 measurements
0x6 : value7
64 measurements
0x7 : value8
128 measurements
End of enumeration elements list.
HYST_UP_CH7 : Channel 7 upper hysteresis
bits : 11 - 11 (1 bit)
access : read-only
Enumeration:
0x0 : HYSTOFF
hysteresis switched off
0x1 : HYST4
hysteresis = 4
0x2 : HYST8
hysteresis = 8
0x3 : HYST16
hysteresis = 16
End of enumeration elements list.
CNT_UP_CH8 : Upper timer trigger threshold channel 8
bits : 16 - 17 (2 bit)
access : read-only
Enumeration:
0x0 : value1
1 measurement
0x1 : value2
2 measurements
0x2 : value3
4 measurements
0x3 : value4
8 measurements
0x4 : value5
16 measurements
0x5 : value6
32 measurements
0x6 : value7
64 measurements
0x7 : value8
128 measurements
End of enumeration elements list.
HYST_UP_CH8 : Channel 8 upper hysteresis
bits : 19 - 19 (1 bit)
access : read-only
Enumeration:
0x0 : HYSTOFF
hysteresis switched off
0x1 : HYST4
hysteresis = 4
0x2 : HYST8
hysteresis = 8
0x3 : HYST16
hysteresis = 16
End of enumeration elements list.
CNT_UP_CH9 : Upper timer trigger threshold channel 9
bits : 24 - 25 (2 bit)
access : read-only
Enumeration:
0x0 : value1
1 measurement
0x1 : value2
2 measurements
0x2 : value3
4 measurements
0x3 : value4
8 measurements
0x4 : value5
16 measurements
0x5 : value6
32 measurements
0x6 : value7
64 measurements
0x7 : value8
128 measurements
End of enumeration elements list.
HYST_UP_CH9 : Channel 9 upper hysteresis
bits : 27 - 27 (1 bit)
access : read-only
Enumeration:
0x0 : HYSTOFF
hysteresis switched off
0x1 : HYST4
hysteresis = 4
0x2 : HYST8
hysteresis = 8
0x3 : HYST16
hysteresis = 16
End of enumeration elements list.
Overvoltage Measurement Mode of Ch 0-5
address_offset : 0xB0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
Ch0 : Measurement mode ch 0
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
0b00 : MMODE0
upper and lower voltage/limit measurement
0b01 : MMODEUV
undervoltage/-limit measurement
0b10 : MMODEOV
overvoltage/-limit measurement
End of enumeration elements list.
Ch1 : Measurement mode ch 1
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
0b00 : MMODE0
upper and lower voltage/limit measurement
0b01 : MMODEUV
undervoltage/-limit measurement
0b10 : MMODEOV
overvoltage/-limit measurement
End of enumeration elements list.
Ch2 : Measurement mode ch 2
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
0b00 : MMODE0
upper and lower voltage/limit measurement
0b01 : MMODEUV
undervoltage/-limit measurement
0b10 : MMODEOV
overvoltage/-limit measurement
End of enumeration elements list.
Ch3 : Measurement mode ch 3
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
0b00 : MMODE0
upper and lower voltage/limit measurement
0b01 : MMODEUV
undervoltage/-limit measurement
0b10 : MMODEOV
overvoltage/-limit measurement
End of enumeration elements list.
Ch4 : Measurement mode ch 4
bits : 8 - 8 (1 bit)
access : read-write
Enumeration:
0b00 : MMODE0
upper and lower voltage/limit measurement
0b01 : MMODEUV
undervoltage/-limit measurement
0b10 : MMODEOV
overvoltage/-limit measurement
End of enumeration elements list.
Ch5 : Measurement mode ch 5
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
0b00 : MMODE0
upper and lower voltage/limit measurement
0b01 : MMODEUV
undervoltage/-limit measurement
0b10 : MMODEOV
overvoltage/-limit measurement
End of enumeration elements list.
ADC2 HV Status Register
address_offset : 0xBC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
READY : HVADC Ready bit
bits : 1 - 0 (0 bit)
access : read-only
Enumeration:
0b0 : Not_ready
Module in power down or in init phase
0b1 : Ready
set automatically 5 ADC clock cycles after module is enabled
End of enumeration elements list.
Channel Settings Bits for Exceptional Sequence Measurement
address_offset : 0xC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ESM_0 : Channel Sequence for Exceptional Sequence Measurement (ESM)
bits : 0 - 4 (5 bit)
access : read-write
Enumeration:
0b000001 : CH0_EN
Channel 0 enable
0b000010 : CH1_EN
Channel 1 enable
0b000100 : CH2_EN
Channel 2 enable
0b001000 : CH3_EN
Channel 3 enable
0b010000 : CH4_EN
Channel 4 enable
0b100000 : CH5_EN
Channel 5 enable
End of enumeration elements list.
ESM_1 : Channel Sequence for Exceptional Sequence Measurement (ESM)
bits : 6 - 8 (3 bit)
access : read-write
Enumeration:
0b0001 : CH6_EN
Channel 6 enable
0b0010 : CH7_EN
Channel 7 enable
0b0100 : CH8_EN
Channel 8 enable
0b1000 : CH9_EN
Channel 9 enable
End of enumeration elements list.
SEL : Exceptional Sequence Measurement Trigger Select
bits : 10 - 9 (0 bit)
access : read-write
Enumeration:
0b0 : CCU6_SEL
ccu6_int starts ESM
0b1 : CP_SEL
cp_clk starts ESM
End of enumeration elements list.
EN : Enable for Exceptional Sequence Measurement Trigger Event
bits : 16 - 15 (0 bit)
access : read-write
Enumeration:
0b0 : Disable
start of ESM disabled
0b1 : Enable
start of ESM enabled
End of enumeration elements list.
STS : Exceptional Sequence Measurement is finished
bits : 17 - 16 (0 bit)
access : read-only
Enumeration:
0b0 : not_active
Exceptional Sequence Measurement not done
0b1 : done
Exceptional Sequence Measurement done
End of enumeration elements list.
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.