Embeetle, an IDE designed from scratch for embedded software developers.address_offset : 0x0 Bytes (0x0)
size : 0x50 byte (0x0)
mem_usage : registers
protection : not protected
ADC3 and ADC4 Control and Status
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ADC3_EN : ADC3 analog frontend Enable
bits : 0 - -1 (0 bit)
access : read-write
Enumeration:
0b0 : DISABLE
ADC3 analog frontend switched off
0b1 : ENABLE
ADC3 analog frontend switched on
End of enumeration elements list.
ADC3_OFS_MEAS_EN : ADC3 Offset Measurement Enable
bits : 1 - 0 (0 bit)
access : read-write
Enumeration:
0b0 : DISABLE
Offset Measurement
0b1 : ENABLE
Offset Measurement
End of enumeration elements list.
ADC3_SOC : ADC3 conversion enable (set after enabling ADC to allow settling of the analog converter part)
bits : 2 - 1 (0 bit)
access : read-write
Enumeration:
0b0 : Disable
ADC3 data processing
0b1 : Enable
ADC3 data processing
End of enumeration elements list.
ADC3_EoC_STS : ADC3 End of Conversion
bits : 4 - 3 (0 bit)
access : read-only
Enumeration:
0b0 : Conversion ongoing
ADC3 conversion still in progress
0b1 : Conversion finished
ADC3 conversion terminated
End of enumeration elements list.
ADC34_REF_SEL : ADC34 reference voltage selection
bits : 11 - 10 (0 bit)
access : read-write
Enumeration:
0b0 : VAREF
use VAREF / VAGND as reference
0b1 : VDD_EXT
use VDD_EXT / GND as reference
End of enumeration elements list.
ADC3_OSR : ADC3 Oversampling Ratio
bits : 12 - 14 (3 bit)
access : read-write
Enumeration:
0b0111 : 128
Factor 128
0b1000 : 256
Factor 256
0b1001 : 512
Factor 512
0b1010 : 1024
Factor 1024
0b1011 : 2048
Factor 2048
End of enumeration elements list.
ADC4_EN : ADC4 analog frontend Enable
bits : 16 - 15 (0 bit)
access : read-write
Enumeration:
0b0 : DISABLE
ADC4 analog frontend switched off
0b1 : ENABLE
ADC4 analog frontend switched on
End of enumeration elements list.
ADC4_OFS_MEAS_EN : ADC4 Offset Measurement Enable
bits : 17 - 16 (0 bit)
access : read-write
Enumeration:
0b0 : DISABLE
Offset Measurement
0b1 : ENABLE
Offset Measurement
End of enumeration elements list.
ADC4_SOC : ADC4 conversion enable (set after enabling ADC to allow settling of the analog converter part)
bits : 18 - 17 (0 bit)
access : read-write
Enumeration:
0b0 : Disable
ADC4 data processing
0b1 : Enable
ADC4 data processing
End of enumeration elements list.
ADC4_EoC_STS : ADC4 End of Conversion
bits : 20 - 19 (0 bit)
access : read-only
Enumeration:
0b0 : Conversion ongoing
ADC4 conversion still in progress
0b1 : Conversion finished
ADC4 conversion terminated
End of enumeration elements list.
ADC34_EoC_CNT : ADC34 EoC counter
bits : 21 - 21 (1 bit)
access : read-write
Enumeration:
0b00 : value0
ADC IRQ with every EoC
0b01 : value1
ADC IRQ with every 8th EoC
0b10 : value2
ADC IRQ with every 16th EoC
0b11 : value3
ADC IRQ with every 32nd EoC
End of enumeration elements list.
ADC34_DITHEN : ADC34 Dithering Enable
bits : 23 - 22 (0 bit)
access : read-write
Enumeration:
0b0 : Disable
ADC34 Dithering
0b1 : Enable
ADC34 Dithering
End of enumeration elements list.
ADC34_DITHVAL : ADC34 Dither Value
bits : 24 - 26 (3 bit)
access : read-write
ADC4_OSR : ADC4 Oversampling Ratio
bits : 28 - 30 (3 bit)
access : read-write
Enumeration:
0b0111 : 128
Factor 128
0b1000 : 256
Factor 256
0b1001 : 512
Factor 512
0b1010 : 1024
Factor 1024
0b1011 : 2048
Factor 2048
End of enumeration elements list.
ADC3_ADC4_RESU
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ADC3_RESU : ADC3 Result Register
bits : 0 - 14 (15 bit)
access : read-only
ADC4_RESU : ADC4 Result Register
bits : 16 - 30 (15 bit)
access : read-only
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.