Embeetle, an IDE designed from scratch for embedded software developers.address_offset : 0x0 Bytes (0x0)
size : 0x8 byte (0x0)
mem_usage : registers
protection : not protected
LIN Transceiver Control and Status
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MODE : LIN transceiver power mode control
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
0b00 : LIN_Sleep_Mode
LIN module switched to LIN Sleep Mode
0b01 : LIN_Receive_Only_Mode
LIN module switched to LIN Receive Only Mode
0b11 : LIN_Normal_Mode
LIN module switched to LIN Normal Mode
End of enumeration elements list.
M_SM_ERR : LIN Transceiver Mode or Slope Mode Error
bits : 3 - 2 (0 bit)
access : read-only
Enumeration:
0b0 : no_Mode_or_Slope_Mode_Error
Status (see corresponding Feedback registers)
0b1 : Mode_or_Slope_Mode_Error
Status (see corresponding Feedback registers)
End of enumeration elements list.
OT_STS : LIN Receiver Overtemperature Status
bits : 4 - 3 (0 bit)
access : read-only
Enumeration:
0b0 : no_Overtemperature
overtemperature occured
0b1 : Overtemperature
overtemperature occured
End of enumeration elements list.
OC_STS : LIN Receiver Overcurrent Status
bits : 5 - 4 (0 bit)
access : read-only
Enumeration:
0b0 : no_Overcurrent
overcurrent status occured
0b1 : Overcurrent
overcurrent status occured
End of enumeration elements list.
TXD_TMOUT_STS : LIN TXD time-out status
bits : 6 - 5 (0 bit)
access : read-only
Enumeration:
0b0 : NO_TIMEOUT
no time-out occured
0b1 : TIMEOUT
time-out occured
End of enumeration elements list.
TXD : LIN Transmitter switch on (only used when LIN_HV_MODE is set)
bits : 9 - 8 (0 bit)
access : read-write
Enumeration:
0b0 : Pull_Down_LIN_Line
Transmitter is switched on
0b1 : Pull_Up_Resistor_is_active
Transmitter is switched off
End of enumeration elements list.
RXD : Output Signal of Receiver
bits : 10 - 9 (0 bit)
access : read-only
SM : LIN Transmitter Slope mode control
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
0b00 : Normal_Slope_Mode
for max. 20 kBaud
0b01 : Fast_Slope_Mode
for max. 40 kBaud
0b10 : Low_Slope_Mode
for max. 10.4 kBaud
0b11 : Flash_Mode
for max. 150 kBaud
End of enumeration elements list.
FB_SM1 : Feedback Signal 1 for Slope Mode Setting
bits : 13 - 12 (0 bit)
access : read-only
FB_SM2 : Feedback Signal 2 for Slope Mode Setting
bits : 14 - 13 (0 bit)
access : read-only
FB_SM3 : Feedback Signal 3 for Slope Mode Setting
bits : 15 - 14 (0 bit)
access : read-only
MODE_FB : Feedback Signals for LIN Transmitter Mode Settings
bits : 16 - 17 (2 bit)
access : read-only
HV_MODE : LIN Transceiver High Voltage Input - Output Mode
bits : 21 - 20 (0 bit)
access : read-write
Enumeration:
0b0 : DISABLE
High Voltage Mode Entry is disabled
0b1 : ENABLE
High Voltage Mode Entry is enabled
End of enumeration elements list.
M_SM_ERR_CLR : LIN Transceiver Mode or Slope Mode Error Clear
bits : 24 - 23 (0 bit)
access : read-write
Enumeration:
0b0 : no_action
Status unchanged
0b1 : Clear
Status clear
End of enumeration elements list.
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.