\n
address_offset : 0x0 Bytes (0x0)
size : 0x40 byte (0x0)
mem_usage : registers
protection : not protected
Power Sequencer Control Register 0
address_offset : 0x0 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
pwr_lp1 : Shutdown Power Mode Select
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_first_boot : Wake on First Boot
bits : 1 - 2 (2 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_sys_reboot : Firmware System Reboot Request
bits : 2 - 4 (3 bit)
access : write-only
Enumeration:
End of enumeration elements list.
pwr_flashen_run : Enable Flash Operation during Run Mode
bits : 3 - 6 (4 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_flashen_slp : Enable Flash Operation during Sleep Mode
bits : 4 - 8 (5 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_retregen_run : Enable Retention Regulator Operation during Run Mode
bits : 5 - 10 (6 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_retregen_slp : Enable Retention Regulator Operation during Sleep Mode
bits : 6 - 12 (7 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_roen_run : Enable 96MHz System Relaxation Oscillator in Run Mode
bits : 7 - 14 (8 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_roen_slp : Enable 96MHz System Relaxation Oscillator in Sleep Mode
bits : 8 - 16 (9 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_nren_run : Enable Nano Oscillator in Run Mode
bits : 9 - 18 (10 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_nren_slp : Enable Nano Oscillator in Sleep Mode
bits : 10 - 20 (11 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_rtcen_run : Enable Real Time Clock Operation during Run Mode
bits : 11 - 22 (12 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_rtcen_slp : Enable Real Time Clock Operation during Sleep Mode
bits : 12 - 24 (13 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_svm12en_run : Enable VDD12_SW SVM operation during Run Mode
bits : 13 - 26 (14 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_svm18en_run : Enable VDD18_SW SVM operation during Run Mode
bits : 15 - 30 (16 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_svmrtcen_run : Enable VRTC SVM operation during Run Mode
bits : 17 - 34 (18 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_svm_vddb_run : Enable VDDB SVM operation during Run Mode
bits : 19 - 38 (20 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_svmtvdd12en_run : Enable TVDD12 SVM operation during Run Mode
bits : 21 - 42 (22 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_vdd12_swen_run : Enable VDD12 switching during Run Mode
bits : 23 - 46 (24 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_vdd12_swen_slp : Enable VDD12 switching during Sleep Mode
bits : 24 - 48 (25 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_vdd18_swen_run : Enable VDD18 switching during Run Mode
bits : 25 - 50 (26 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_vdd18_swen_slp : Enable VDD18 switching during Sleep Mode
bits : 26 - 52 (27 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_tvdd12_swen_run : Enable TVDD12 switching during Run Mode
bits : 27 - 54 (28 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_tvdd12_swen_slp : Enable TVDD12 switching during Sleep Mode
bits : 28 - 56 (29 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_rcen_run : Enable 4MHz RC oscillator operation during Run Mode for LP2 and LP3
bits : 29 - 58 (30 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_rcen_slp : Enable 4MHz RC oscillator operation during Sleep Mode for LP1
bits : 30 - 60 (31 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_osc_select : Select Primary System Oscillator 96MHz or 4MHz
bits : 31 - 62 (32 bit)
access : read-write
Enumeration:
End of enumeration elements list.
Power Sequencer Control Register 4 (Internal Test Only)
address_offset : 0x10 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
pwr_tm_ps_2_gpio : Internal Use Only
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_tm_fast_timers : Internal Use Only
bits : 1 - 2 (2 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_usb_dis_comp : Internal Use Only
bits : 3 - 6 (4 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_ro_tstclk_en : Internal Use Only
bits : 4 - 8 (5 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_nr_clk_gate_en : Internal Use Only
bits : 5 - 10 (6 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_ext_clk_in_en : Internal Use Only
bits : 6 - 12 (7 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_pseq_32k_en : Internal Use Only
bits : 7 - 14 (8 bit)
access : read-write
Enumeration:
End of enumeration elements list.
Power Sequencer Control Register 5 (Trim 0)
address_offset : 0x14 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
pwr_trim_svm_bg : Power Manager Bandgap trim setting
bits : 0 - 8 (9 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_trim_bias : Power Manager Bias Current trim setting
bits : 9 - 23 (15 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_trim_retreg : Retention Regulator trim setting
bits : 15 - 35 (21 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_rtc_trim : Real Time Clock trim setting
bits : 21 - 45 (25 bit)
access : read-write
Enumeration:
End of enumeration elements list.
Power Sequencer Control Register 6 (Trim 1)
address_offset : 0x18 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
pwr_trim_usb_bias : USB Bias Current trim setting
bits : 0 - 2 (3 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_trim_usb_pm_res : USB Data Plus Slew Rate trim setting
bits : 3 - 9 (7 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_trim_usb_dm_res : USB Data Minus Slew Rate trim setting
bits : 7 - 17 (11 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_trim_osc_vref : Relaxation Oscillator trim setting
bits : 11 - 30 (20 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_trim_crypto_osc : Crypto Oscillator trim setting
bits : 20 - 48 (29 bit)
access : read-write
Enumeration:
End of enumeration elements list.
Power Sequencer Control Register 7
address_offset : 0x1C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
pwr_flash_pd_lookahead : Flash Powerdown Lookahead Flag
bits : 0 - 0 (1 bit)
access : read-only
Enumeration:
End of enumeration elements list.
Power Sequencer Flags
address_offset : 0x20 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
pwr_first_boot : Initial Boot event detected flag
bits : 0 - 0 (1 bit)
access : read-only
Enumeration:
End of enumeration elements list.
pwr_sys_reboot : Firmware Reset event detected flag
bits : 1 - 2 (2 bit)
access : read-only
Enumeration:
End of enumeration elements list.
pwr_power_fail : Power Fail event detected flag
bits : 2 - 4 (3 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_boot_fail : Boot Fail event detected flag
bits : 3 - 6 (4 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_flash_discharge : Flash Discharged During Powerfail event detected flag
bits : 4 - 8 (5 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_iowakeup : GPIO Wakeup event detected flag
bits : 5 - 10 (6 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_vdd12_rst_bad : VDD12_SW Comparator Tripped event detected flag
bits : 6 - 12 (7 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_vdd18_rst_bad : VDD18_SW Comparator Tripped event detected flag
bits : 7 - 14 (8 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_vrtc_rst_bad : VRTC Comparator Tripped event detected flag
bits : 8 - 16 (9 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_vddb_rst_bad : VDDB Comparator Tripped event detected flag
bits : 9 - 18 (10 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_tvdd12_rst_bad : TVDD12 Comparator Tripped event detected flag
bits : 10 - 20 (11 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_por18z_fail_latch : POR18 and POR18_bg have been tripped
bits : 11 - 22 (12 bit)
access : read-write
Enumeration:
End of enumeration elements list.
rtc_cmpr0 : RTC Comparator 0 Match event detected flag
bits : 12 - 24 (13 bit)
access : read-only
Enumeration:
End of enumeration elements list.
rtc_cmpr1 : RTC Comparator 1 Match event detected flag
bits : 13 - 26 (14 bit)
access : read-only
Enumeration:
End of enumeration elements list.
rtc_prescale_cmp : RTC Prescale Comparator Match event detected flag
bits : 14 - 28 (15 bit)
access : read-only
Enumeration:
End of enumeration elements list.
rtc_rollover : RTC Rollover event detected flag
bits : 15 - 30 (16 bit)
access : read-only
Enumeration:
End of enumeration elements list.
pwr_usb_plug_wakeup : USB Power Connect Wakeup event detected flag
bits : 16 - 32 (17 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_usb_remove_wakeup : USB Power Remove Wakeup event detected flag
bits : 17 - 34 (18 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_tvdd12_bad : Retention Regulator POR Tripped event detected flag
bits : 18 - 36 (19 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_vddio_rst_bad : VDDIO Comparator Tripped
bits : 19 - 38 (20 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_vddioh_rst_bad : VDDIOH Comparator Tripped
bits : 20 - 40 (21 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_isoz_vddio_fail : VDDIO Isolation POR Tripped
bits : 21 - 42 (22 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_isoz_vddioh_fail : VDDIOH Isolation POR Tripped
bits : 22 - 44 (23 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_nanoring_wakeup_flag : Wakeup Triggered by Nanoring Wakeup
bits : 23 - 46 (24 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_watchdog_rstn_flag : Power Sequencer Reset Triggered by Watchdog Flag
bits : 24 - 48 (25 bit)
access : read-write
Enumeration:
End of enumeration elements list.
Power Sequencer Flags Mask Register
address_offset : 0x24 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
pwr_sys_reboot : Mask for system reboot detect
bits : 1 - 2 (2 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_power_fail : Mask for previous power fail detect
bits : 2 - 4 (3 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_boot_fail : Mask for previous boot fail detect
bits : 3 - 6 (4 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_flash_discharge : Mask for flash discharge event
bits : 4 - 8 (5 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_iowakeup : Mask for GPIO wakeup event detect
bits : 5 - 10 (6 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_vdd12_rst_bad : Mask for VDD12 rst event
bits : 6 - 12 (7 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_vdd18_rst_bad : Mask for VDD18 rst event
bits : 7 - 14 (8 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_vrtc_rst_bad : Mask for VRTC rst event
bits : 8 - 16 (9 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_vddb_rst_bad : Mask for VDDB rst event
bits : 9 - 18 (10 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_tvdd12_rst_bad : Mask for TVDD12 rst event
bits : 10 - 20 (11 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_por18z_fail_latch : Mask for POR18 powerfail event
bits : 11 - 22 (12 bit)
access : read-write
Enumeration:
End of enumeration elements list.
rtc_cmpr0 : Mask for RTC compare 0 event
bits : 12 - 24 (13 bit)
access : read-write
Enumeration:
End of enumeration elements list.
rtc_cmpr1 : Mask for RTC compare 1 event
bits : 13 - 26 (14 bit)
access : read-write
Enumeration:
End of enumeration elements list.
rtc_prescale_cmp : Mask for RTC prescale compare event
bits : 14 - 28 (15 bit)
access : read-write
Enumeration:
End of enumeration elements list.
rtc_rollover : Mask for RTC rollover event
bits : 15 - 30 (16 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_usb_plug_wakeup : Mask for USB plug connect event
bits : 16 - 32 (17 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_usb_remove_wakeup : Mask for USB plug disconnect event
bits : 17 - 34 (18 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_tvdd12_bad : Mask for TVDD12 power fail event
bits : 18 - 36 (19 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_vddio_rst_bad : Mask for VDDIO Comparator Tripped
bits : 19 - 38 (20 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_vddioh_rst_bad : Mask for VDDIOH Comparator Tripped
bits : 20 - 40 (21 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_isoz_vddio_fail : Mask for VDDIO Isolation POR Tripped
bits : 21 - 42 (22 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_isoz_vddioh_fail : Mask for VDDIOH Isolation POR Tripped
bits : 22 - 44 (23 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_nanoring_wakeup_flag : Mask for Wakeup Triggered by Nanoring Wakeup
bits : 23 - 46 (24 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_watchdog_rstn_flag : Mask for Power Sequencer Reset Triggered by Watchdog Flag
bits : 24 - 48 (25 bit)
access : read-write
Enumeration:
End of enumeration elements list.
Critical Setting Write Protect Register
address_offset : 0x2C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
bypass_seq : Write Protect Bypass Sequence Write
bits : 0 - 7 (8 bit)
access : read-write
Enumeration:
End of enumeration elements list.
rtc_seq : Write Protect RTC Sequence Write
bits : 8 - 23 (16 bit)
access : read-write
Enumeration:
End of enumeration elements list.
rtc : Write Protect from RTC
bits : 28 - 56 (29 bit)
access : read-write
Enumeration:
End of enumeration elements list.
info : Write Protect from Info Block
bits : 29 - 58 (30 bit)
access : read-write
Enumeration:
End of enumeration elements list.
bypass : Write Protect Bypass
bits : 30 - 60 (31 bit)
access : read-write
Enumeration:
End of enumeration elements list.
wp : Critical Setting Write Protect
bits : 31 - 62 (32 bit)
access : read-write
Enumeration:
End of enumeration elements list.
Retention Control Register 0
address_offset : 0x30 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
retn_ctrl_en : Retention Controller Enable
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
End of enumeration elements list.
rc_rel_ccg_early : Early Core Clock Gate Release
bits : 1 - 2 (2 bit)
access : read-write
Enumeration:
End of enumeration elements list.
rc_use_flc_twk : Enable Flash Controller TWake Timer
bits : 2 - 4 (3 bit)
access : read-write
Enumeration:
End of enumeration elements list.
rc_poll_flash : Enable Automatic Flash Polling for Wakeup
bits : 3 - 6 (4 bit)
access : read-write
Enumeration:
End of enumeration elements list.
Retention Control Register 1
address_offset : 0x34 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
rtc_twk : Retention Controller TWake Cycle Count
bits : 0 - 3 (4 bit)
access : read-write
Enumeration:
End of enumeration elements list.
Power Misc Controls
address_offset : 0x38 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
invert_4_mask_bits : Invert Sense of Power Mask Flags for RTC
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
End of enumeration elements list.
RTC Misc Controls
address_offset : 0x3C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
timer_async_rd : None
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
End of enumeration elements list.
timer_async_wr : None
bits : 1 - 2 (2 bit)
access : read-write
Enumeration:
End of enumeration elements list.
timer_auto_update : None
bits : 2 - 4 (3 bit)
access : read-write
Enumeration:
End of enumeration elements list.
ssb_performance : None
bits : 3 - 6 (4 bit)
access : read-write
Enumeration:
End of enumeration elements list.
Power Sequencer Control Register 1
address_offset : 0x4 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
pwr_clr_io_event_latch : Clear all GPIO Event Seen Latches
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_clr_io_cfg_latch : Clear all GPIO Configuration Latches
bits : 1 - 2 (2 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_mbus_gate : Freeze GPIO MBus State
bits : 2 - 4 (3 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_discharge_en : Enable Flash Discharge During Powerfail Event
bits : 3 - 6 (4 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_tvdd12_well : TVDD12 Well Switch
bits : 4 - 8 (5 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_sram_nwell_sw : SRAM n-Well Switch
bits : 5 - 10 (6 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_auto_mbus_gate : Automatically Set/Clear GPIO MBus Gate
bits : 6 - 12 (7 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_svm_vddio_en_run : Enable VDDIO SVM Run for LP2 and LP3
bits : 8 - 16 (9 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_svm_vddioh_en_run : Enable VDDIOH SVM Run for LP2 and LP3
bits : 10 - 20 (11 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_retreg_src_v12 : Enable VDDIO SVM Run for LP2 and LP3
bits : 12 - 24 (13 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_retreg_src_vrtc : Enables VRTC Rail as Retention Power Su
bits : 13 - 26 (14 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_retreg_src_v18 : Enables VDD18 Rail as Retention Power Supply
bits : 14 - 28 (15 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_vddio_en_iso_por : Enable VDDIO Isolation POR
bits : 16 - 32 (17 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_vddioh_en_iso_por : Enable VDDIOH Isolation POR
bits : 17 - 34 (18 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_lp0_core_resume_en : Enable Core Resume to Toggle during LP0
bits : 18 - 36 (19 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_lp1_core_rstn_en : Enable Core RSTN to Toggle during LP1
bits : 19 - 38 (20 bit)
access : read-write
Enumeration:
End of enumeration elements list.
Power Sequencer Control Register 2
address_offset : 0x8 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
pwr_vdd12_hyst : VDD12_SW Comparator Hysteresis Setting
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_vdd18_hyst : VDD18_SW Comparator Hysteresis Setting
bits : 2 - 5 (4 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_vrtc_hyst : VRTC Comparator Hysteresis Setting
bits : 4 - 9 (6 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_vddb_hyst : VDDB Comparator Hysteresis Setting
bits : 6 - 13 (8 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_tvdd12_hyst : TVDD12 Comparator Hysteresis Setting
bits : 8 - 17 (10 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_vddio_hyst : VDDIO Comparator Hysteresis Setting
bits : 10 - 21 (12 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_vddioh_hyst : VDDIO Comparator Hysteresis Setting
bits : 12 - 25 (14 bit)
access : read-write
Enumeration:
End of enumeration elements list.
Power Sequencer Control Register 3
address_offset : 0xC Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
pwr_rosel : Relaxation Oscillator Stable Timeout
bits : 0 - 2 (3 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_fltrrosel : Window of time power must be valid before entering Run mode.
bits : 3 - 8 (6 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_svm_clk_mux : SVM Clock Mux
bits : 6 - 13 (8 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_ro_clk_mux : Relaxation Clock Mux
bits : 8 - 17 (10 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_failsel : Timeout before rebooting during PowerFail/BootFail events.
bits : 10 - 22 (13 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_ro_div : Frequency Divider for 96MHz Relaxation Oscillator
bits : 16 - 34 (19 bit)
access : read-write
Enumeration:
End of enumeration elements list.
pwr_rc_div : Frequency Divider for 4MHz RC Oscillator
bits : 20 - 41 (22 bit)
access : read-write
Enumeration:
End of enumeration elements list.
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.