\n
address_offset : 0x0 Bytes (0x0)
size : 0xC byte (0x0)
mem_usage : registers
protection : not protected
Analog Comparator 0 Control Register
address_offset : 0x0 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ACMPEN : Analog Comparator 0 Enable Control\nNote: Analog comparator output needs to wait 2 us stable time after ACMPEN is set.
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Analog Comparator 0 Disabled
#1 : 1
Analog Comparator 0 Enabled
End of enumeration elements list.
ACMPIE : Analog Comparator 0 Interrupt Enable Control\n
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Interrupt function Disabled
#1 : 1
Interrupt function Enabled
End of enumeration elements list.
HYSEN : Analog Comparator 0 Hysteresis Enable Control\n
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Hysteresis function Disabled
#1 : 1
Hysteresis function Enabled
End of enumeration elements list.
NEGSEL : Analog Comparator 0 Negative Input Selection\n
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
The source of the negative comparator input is from ACMP0_N pin
#1 : 1
The internal band-gap voltage is selected as the source of negative comparator input
End of enumeration elements list.
ACMPOINV : Analog Comparator 0 Output Inverse Enable Control (M05xxDE Only)\n
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
The comparator output inverse function Disabled
#1 : 1
The comparator output inverse function Enabled
End of enumeration elements list.
Analog Comparator 1 Control Register
address_offset : 0x4 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ACMPEN : Analog Comparator 1 Enable Control\nNote: Analog comparator output needs to wait 2 us stable time after ACMPEN is set.
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Analog comparator 1 Disabled
#1 : 1
Analog comparator 1 Enabled
End of enumeration elements list.
ACMPIE : Analog Comparator 1 Interrupt Enable Control\n
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Interrupt function Disabled
#1 : 1
Interrupt function Enabled
End of enumeration elements list.
HYSEN : Analog Comparator 1 Hysteresis Enable Control\n
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Hysteresis function Disabled
#1 : 1
Hysteresis function Enabled
End of enumeration elements list.
NEGSEL : Analog Comparator 1 Negative Input Selection\n
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
The source of the negative comparator input is from ACMP1_N pin
#1 : 1
The internal band-gap voltage is selected as the source of negative comparator input
End of enumeration elements list.
ACMPOINV : Analog Comparator 1 Output Inverse Enable Control (M05xxDE Only)\n
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
The comparator output inverse function Disabled
#1 : 1
The comparator output inverse function Enabled
End of enumeration elements list.
Analog Comparator 0/1 Status Register
address_offset : 0x8 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ACMPF0 : Analog Comparator 0 Flag\nThis bit is set by hardware whenever the comparator 0 output changes state. This will generate an interrupt if ACMP_CR0[1] is set to 1.\nNote: Write 1 to clear this bit to 0.
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Analog comparator 0 output does not change
#1 : 1
Analog comparator 0 output changed since this bit was cleared to 0
End of enumeration elements list.
ACMPF1 : Analog Comparator 1 Flag\nThis bit is set by hardware whenever the comparator 1 output changes state. This will generate an interrupt if ACMP_CR1[1] is set to 1.\nNote: Write 1 to clear this bit to 0.
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Analog comparator 1 output does not change
#1 : 1
Analog comparator 1 output changed since this bit was cleared to 0
End of enumeration elements list.
ACMPO0 : Analog Comparator 0 Output\n
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Analog comparator 0 outputs 0
#1 : 1
Analog comparator 0 outputs 1
End of enumeration elements list.
ACMPO1 : Analog Comparator 1 Output\n
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Analog comparator 1 outputs 0
#1 : 1
Analog comparator 1 outputs 1
End of enumeration elements list.
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.