\n
address_offset : 0x400 Bytes (0x0)
size : 0x44 byte (0x0)
mem_usage : registers
protection : not protected
address_offset : 0x460 Bytes (0x0)
size : 0x4 byte (0x0)
mem_usage : registers
protection : not protected
address_offset : 0x500 Bytes (0x0)
size : 0x30 byte (0x0)
mem_usage : registers
protection : not protected
address_offset : 0x600 Bytes (0x0)
size : 0x10 byte (0x0)
mem_usage : registers
protection : not protected
address_offset : 0x480 Bytes (0x0)
size : 0x10 byte (0x0)
mem_usage : registers
protection : not protected
PDMA Channel Control Register
address_offset : 0x400 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CHEN0 : PDMA Channel Enable Bits\nSet this bit to 1 to enable PDMAn operation. Channel cannot be active if it is not set as enabled.\nNote: Setting the corresponding bit of PDMA_PAUSE or PDMA_CHRST register will also clear this bit.
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel [n] Disabled
#1 : 1
PDMA channel [n] Enabled
End of enumeration elements list.
CHEN1 : PDMA Channel Enable Bits\nSet this bit to 1 to enable PDMAn operation. Channel cannot be active if it is not set as enabled.\nNote: Setting the corresponding bit of PDMA_PAUSE or PDMA_CHRST register will also clear this bit.
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel [n] Disabled
#1 : 1
PDMA channel [n] Enabled
End of enumeration elements list.
CHEN2 : PDMA Channel Enable Bits\nSet this bit to 1 to enable PDMAn operation. Channel cannot be active if it is not set as enabled.\nNote: Setting the corresponding bit of PDMA_PAUSE or PDMA_CHRST register will also clear this bit.
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel [n] Disabled
#1 : 1
PDMA channel [n] Enabled
End of enumeration elements list.
CHEN3 : PDMA Channel Enable Bits\nSet this bit to 1 to enable PDMAn operation. Channel cannot be active if it is not set as enabled.\nNote: Setting the corresponding bit of PDMA_PAUSE or PDMA_CHRST register will also clear this bit.
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel [n] Disabled
#1 : 1
PDMA channel [n] Enabled
End of enumeration elements list.
CHEN4 : PDMA Channel Enable Bits\nSet this bit to 1 to enable PDMAn operation. Channel cannot be active if it is not set as enabled.\nNote: Setting the corresponding bit of PDMA_PAUSE or PDMA_CHRST register will also clear this bit.
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel [n] Disabled
#1 : 1
PDMA channel [n] Enabled
End of enumeration elements list.
CHEN5 : PDMA Channel Enable Bits\nSet this bit to 1 to enable PDMAn operation. Channel cannot be active if it is not set as enabled.\nNote: Setting the corresponding bit of PDMA_PAUSE or PDMA_CHRST register will also clear this bit.
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel [n] Disabled
#1 : 1
PDMA channel [n] Enabled
End of enumeration elements list.
CHEN6 : PDMA Channel Enable Bits\nSet this bit to 1 to enable PDMAn operation. Channel cannot be active if it is not set as enabled.\nNote: Setting the corresponding bit of PDMA_PAUSE or PDMA_CHRST register will also clear this bit.
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel [n] Disabled
#1 : 1
PDMA channel [n] Enabled
End of enumeration elements list.
CHEN7 : PDMA Channel Enable Bits\nSet this bit to 1 to enable PDMAn operation. Channel cannot be active if it is not set as enabled.\nNote: Setting the corresponding bit of PDMA_PAUSE or PDMA_CHRST register will also clear this bit.
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel [n] Disabled
#1 : 1
PDMA channel [n] Enabled
End of enumeration elements list.
CHEN8 : PDMA Channel Enable Bits\nSet this bit to 1 to enable PDMAn operation. Channel cannot be active if it is not set as enabled.\nNote: Setting the corresponding bit of PDMA_PAUSE or PDMA_CHRST register will also clear this bit.
bits : 8 - 8 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel [n] Disabled
#1 : 1
PDMA channel [n] Enabled
End of enumeration elements list.
CHEN9 : PDMA Channel Enable Bits\nSet this bit to 1 to enable PDMAn operation. Channel cannot be active if it is not set as enabled.\nNote: Setting the corresponding bit of PDMA_PAUSE or PDMA_CHRST register will also clear this bit.
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel [n] Disabled
#1 : 1
PDMA channel [n] Enabled
End of enumeration elements list.
CHEN10 : PDMA Channel Enable Bits\nSet this bit to 1 to enable PDMAn operation. Channel cannot be active if it is not set as enabled.\nNote: Setting the corresponding bit of PDMA_PAUSE or PDMA_CHRST register will also clear this bit.
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel [n] Disabled
#1 : 1
PDMA channel [n] Enabled
End of enumeration elements list.
CHEN11 : PDMA Channel Enable Bits\nSet this bit to 1 to enable PDMAn operation. Channel cannot be active if it is not set as enabled.\nNote: Setting the corresponding bit of PDMA_PAUSE or PDMA_CHRST register will also clear this bit.
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel [n] Disabled
#1 : 1
PDMA channel [n] Enabled
End of enumeration elements list.
CHEN12 : PDMA Channel Enable Bits\nSet this bit to 1 to enable PDMAn operation. Channel cannot be active if it is not set as enabled.\nNote: Setting the corresponding bit of PDMA_PAUSE or PDMA_CHRST register will also clear this bit.
bits : 12 - 12 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel [n] Disabled
#1 : 1
PDMA channel [n] Enabled
End of enumeration elements list.
CHEN13 : PDMA Channel Enable Bits\nSet this bit to 1 to enable PDMAn operation. Channel cannot be active if it is not set as enabled.\nNote: Setting the corresponding bit of PDMA_PAUSE or PDMA_CHRST register will also clear this bit.
bits : 13 - 13 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel [n] Disabled
#1 : 1
PDMA channel [n] Enabled
End of enumeration elements list.
CHEN14 : PDMA Channel Enable Bits\nSet this bit to 1 to enable PDMAn operation. Channel cannot be active if it is not set as enabled.\nNote: Setting the corresponding bit of PDMA_PAUSE or PDMA_CHRST register will also clear this bit.
bits : 14 - 14 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel [n] Disabled
#1 : 1
PDMA channel [n] Enabled
End of enumeration elements list.
CHEN15 : PDMA Channel Enable Bits\nSet this bit to 1 to enable PDMAn operation. Channel cannot be active if it is not set as enabled.\nNote: Setting the corresponding bit of PDMA_PAUSE or PDMA_CHRST register will also clear this bit.
bits : 15 - 15 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel [n] Disabled
#1 : 1
PDMA channel [n] Enabled
End of enumeration elements list.
PDMA Transfer Pause Control Register
address_offset : 0x404 Bytes (0x0)
access : write-only
reset_value : 0x0
reset_Mask : 0x0
PAUSE0 : PDMA Channel n Transfer Pause Control (Write Only)
bits : 0 - 0 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Pause PDMA channel n transfer
End of enumeration elements list.
PAUSE1 : PDMA Channel n Transfer Pause Control (Write Only)
bits : 1 - 1 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Pause PDMA channel n transfer
End of enumeration elements list.
PAUSE2 : PDMA Channel n Transfer Pause Control (Write Only)
bits : 2 - 2 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Pause PDMA channel n transfer
End of enumeration elements list.
PAUSE3 : PDMA Channel n Transfer Pause Control (Write Only)
bits : 3 - 3 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Pause PDMA channel n transfer
End of enumeration elements list.
PAUSE4 : PDMA Channel n Transfer Pause Control (Write Only)
bits : 4 - 4 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Pause PDMA channel n transfer
End of enumeration elements list.
PAUSE5 : PDMA Channel n Transfer Pause Control (Write Only)
bits : 5 - 5 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Pause PDMA channel n transfer
End of enumeration elements list.
PAUSE6 : PDMA Channel n Transfer Pause Control (Write Only)
bits : 6 - 6 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Pause PDMA channel n transfer
End of enumeration elements list.
PAUSE7 : PDMA Channel n Transfer Pause Control (Write Only)
bits : 7 - 7 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Pause PDMA channel n transfer
End of enumeration elements list.
PAUSE8 : PDMA Channel n Transfer Pause Control (Write Only)
bits : 8 - 8 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Pause PDMA channel n transfer
End of enumeration elements list.
PAUSE9 : PDMA Channel n Transfer Pause Control (Write Only)
bits : 9 - 9 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Pause PDMA channel n transfer
End of enumeration elements list.
PAUSE10 : PDMA Channel n Transfer Pause Control (Write Only)
bits : 10 - 10 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Pause PDMA channel n transfer
End of enumeration elements list.
PAUSE11 : PDMA Channel n Transfer Pause Control (Write Only)
bits : 11 - 11 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Pause PDMA channel n transfer
End of enumeration elements list.
PAUSE12 : PDMA Channel n Transfer Pause Control (Write Only)
bits : 12 - 12 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Pause PDMA channel n transfer
End of enumeration elements list.
PAUSE13 : PDMA Channel n Transfer Pause Control (Write Only)
bits : 13 - 13 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Pause PDMA channel n transfer
End of enumeration elements list.
PAUSE14 : PDMA Channel n Transfer Pause Control (Write Only)
bits : 14 - 14 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Pause PDMA channel n transfer
End of enumeration elements list.
PAUSE15 : PDMA Channel n Transfer Pause Control (Write Only)
bits : 15 - 15 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Pause PDMA channel n transfer
End of enumeration elements list.
PDMA Software Request Register
address_offset : 0x408 Bytes (0x0)
access : write-only
reset_value : 0x0
reset_Mask : 0x0
SWREQ0 : PDMA Software Request (Write Only)\nSet this bit to 1 to generate a software request to PDMA [n].\nNote 1: User can read PDMA_TRGSTS register to know which channel is on active. Active flag may be triggered by software request or peripheral request.\nNote 2: If user does not enable corresponding PDMA channel, the software request will be ignored.
bits : 0 - 0 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Generate a software request
End of enumeration elements list.
SWREQ1 : PDMA Software Request (Write Only)\nSet this bit to 1 to generate a software request to PDMA [n].\nNote 1: User can read PDMA_TRGSTS register to know which channel is on active. Active flag may be triggered by software request or peripheral request.\nNote 2: If user does not enable corresponding PDMA channel, the software request will be ignored.
bits : 1 - 1 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Generate a software request
End of enumeration elements list.
SWREQ2 : PDMA Software Request (Write Only)\nSet this bit to 1 to generate a software request to PDMA [n].\nNote 1: User can read PDMA_TRGSTS register to know which channel is on active. Active flag may be triggered by software request or peripheral request.\nNote 2: If user does not enable corresponding PDMA channel, the software request will be ignored.
bits : 2 - 2 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Generate a software request
End of enumeration elements list.
SWREQ3 : PDMA Software Request (Write Only)\nSet this bit to 1 to generate a software request to PDMA [n].\nNote 1: User can read PDMA_TRGSTS register to know which channel is on active. Active flag may be triggered by software request or peripheral request.\nNote 2: If user does not enable corresponding PDMA channel, the software request will be ignored.
bits : 3 - 3 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Generate a software request
End of enumeration elements list.
SWREQ4 : PDMA Software Request (Write Only)\nSet this bit to 1 to generate a software request to PDMA [n].\nNote 1: User can read PDMA_TRGSTS register to know which channel is on active. Active flag may be triggered by software request or peripheral request.\nNote 2: If user does not enable corresponding PDMA channel, the software request will be ignored.
bits : 4 - 4 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Generate a software request
End of enumeration elements list.
SWREQ5 : PDMA Software Request (Write Only)\nSet this bit to 1 to generate a software request to PDMA [n].\nNote 1: User can read PDMA_TRGSTS register to know which channel is on active. Active flag may be triggered by software request or peripheral request.\nNote 2: If user does not enable corresponding PDMA channel, the software request will be ignored.
bits : 5 - 5 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Generate a software request
End of enumeration elements list.
SWREQ6 : PDMA Software Request (Write Only)\nSet this bit to 1 to generate a software request to PDMA [n].\nNote 1: User can read PDMA_TRGSTS register to know which channel is on active. Active flag may be triggered by software request or peripheral request.\nNote 2: If user does not enable corresponding PDMA channel, the software request will be ignored.
bits : 6 - 6 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Generate a software request
End of enumeration elements list.
SWREQ7 : PDMA Software Request (Write Only)\nSet this bit to 1 to generate a software request to PDMA [n].\nNote 1: User can read PDMA_TRGSTS register to know which channel is on active. Active flag may be triggered by software request or peripheral request.\nNote 2: If user does not enable corresponding PDMA channel, the software request will be ignored.
bits : 7 - 7 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Generate a software request
End of enumeration elements list.
SWREQ8 : PDMA Software Request (Write Only)\nSet this bit to 1 to generate a software request to PDMA [n].\nNote 1: User can read PDMA_TRGSTS register to know which channel is on active. Active flag may be triggered by software request or peripheral request.\nNote 2: If user does not enable corresponding PDMA channel, the software request will be ignored.
bits : 8 - 8 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Generate a software request
End of enumeration elements list.
SWREQ9 : PDMA Software Request (Write Only)\nSet this bit to 1 to generate a software request to PDMA [n].\nNote 1: User can read PDMA_TRGSTS register to know which channel is on active. Active flag may be triggered by software request or peripheral request.\nNote 2: If user does not enable corresponding PDMA channel, the software request will be ignored.
bits : 9 - 9 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Generate a software request
End of enumeration elements list.
SWREQ10 : PDMA Software Request (Write Only)\nSet this bit to 1 to generate a software request to PDMA [n].\nNote 1: User can read PDMA_TRGSTS register to know which channel is on active. Active flag may be triggered by software request or peripheral request.\nNote 2: If user does not enable corresponding PDMA channel, the software request will be ignored.
bits : 10 - 10 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Generate a software request
End of enumeration elements list.
SWREQ11 : PDMA Software Request (Write Only)\nSet this bit to 1 to generate a software request to PDMA [n].\nNote 1: User can read PDMA_TRGSTS register to know which channel is on active. Active flag may be triggered by software request or peripheral request.\nNote 2: If user does not enable corresponding PDMA channel, the software request will be ignored.
bits : 11 - 11 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Generate a software request
End of enumeration elements list.
SWREQ12 : PDMA Software Request (Write Only)\nSet this bit to 1 to generate a software request to PDMA [n].\nNote 1: User can read PDMA_TRGSTS register to know which channel is on active. Active flag may be triggered by software request or peripheral request.\nNote 2: If user does not enable corresponding PDMA channel, the software request will be ignored.
bits : 12 - 12 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Generate a software request
End of enumeration elements list.
SWREQ13 : PDMA Software Request (Write Only)\nSet this bit to 1 to generate a software request to PDMA [n].\nNote 1: User can read PDMA_TRGSTS register to know which channel is on active. Active flag may be triggered by software request or peripheral request.\nNote 2: If user does not enable corresponding PDMA channel, the software request will be ignored.
bits : 13 - 13 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Generate a software request
End of enumeration elements list.
SWREQ14 : PDMA Software Request (Write Only)\nSet this bit to 1 to generate a software request to PDMA [n].\nNote 1: User can read PDMA_TRGSTS register to know which channel is on active. Active flag may be triggered by software request or peripheral request.\nNote 2: If user does not enable corresponding PDMA channel, the software request will be ignored.
bits : 14 - 14 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Generate a software request
End of enumeration elements list.
SWREQ15 : PDMA Software Request (Write Only)\nSet this bit to 1 to generate a software request to PDMA [n].\nNote 1: User can read PDMA_TRGSTS register to know which channel is on active. Active flag may be triggered by software request or peripheral request.\nNote 2: If user does not enable corresponding PDMA channel, the software request will be ignored.
bits : 15 - 15 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Generate a software request
End of enumeration elements list.
PDMA Channel Request Status Register
address_offset : 0x40C Bytes (0x0)
access : read-only
reset_value : 0x0
reset_Mask : 0x0
REQSTS0 : PDMA Channel Request Status (Read Only)\nThis flag indicates whether channel[n] have a request or not, no matter request from software or peripheral. When PDMA controller finishes channel transfer, this bit will be cleared automatically. \nNote: If user pauses or resets each PDMA transfer by setting PDMA_PAUSE or PDMA_CHRST register respectively, this bit will be cleared automatically after finishing the current transfer.
bits : 0 - 0 (1 bit)
access : read-only
Enumeration:
#0 : 0
PDMA Channel n has no request
#1 : 1
PDMA Channel n has a request
End of enumeration elements list.
REQSTS1 : PDMA Channel Request Status (Read Only)\nThis flag indicates whether channel[n] have a request or not, no matter request from software or peripheral. When PDMA controller finishes channel transfer, this bit will be cleared automatically. \nNote: If user pauses or resets each PDMA transfer by setting PDMA_PAUSE or PDMA_CHRST register respectively, this bit will be cleared automatically after finishing the current transfer.
bits : 1 - 1 (1 bit)
access : read-only
Enumeration:
#0 : 0
PDMA Channel n has no request
#1 : 1
PDMA Channel n has a request
End of enumeration elements list.
REQSTS2 : PDMA Channel Request Status (Read Only)\nThis flag indicates whether channel[n] have a request or not, no matter request from software or peripheral. When PDMA controller finishes channel transfer, this bit will be cleared automatically. \nNote: If user pauses or resets each PDMA transfer by setting PDMA_PAUSE or PDMA_CHRST register respectively, this bit will be cleared automatically after finishing the current transfer.
bits : 2 - 2 (1 bit)
access : read-only
Enumeration:
#0 : 0
PDMA Channel n has no request
#1 : 1
PDMA Channel n has a request
End of enumeration elements list.
REQSTS3 : PDMA Channel Request Status (Read Only)\nThis flag indicates whether channel[n] have a request or not, no matter request from software or peripheral. When PDMA controller finishes channel transfer, this bit will be cleared automatically. \nNote: If user pauses or resets each PDMA transfer by setting PDMA_PAUSE or PDMA_CHRST register respectively, this bit will be cleared automatically after finishing the current transfer.
bits : 3 - 3 (1 bit)
access : read-only
Enumeration:
#0 : 0
PDMA Channel n has no request
#1 : 1
PDMA Channel n has a request
End of enumeration elements list.
REQSTS4 : PDMA Channel Request Status (Read Only)\nThis flag indicates whether channel[n] have a request or not, no matter request from software or peripheral. When PDMA controller finishes channel transfer, this bit will be cleared automatically. \nNote: If user pauses or resets each PDMA transfer by setting PDMA_PAUSE or PDMA_CHRST register respectively, this bit will be cleared automatically after finishing the current transfer.
bits : 4 - 4 (1 bit)
access : read-only
Enumeration:
#0 : 0
PDMA Channel n has no request
#1 : 1
PDMA Channel n has a request
End of enumeration elements list.
REQSTS5 : PDMA Channel Request Status (Read Only)\nThis flag indicates whether channel[n] have a request or not, no matter request from software or peripheral. When PDMA controller finishes channel transfer, this bit will be cleared automatically. \nNote: If user pauses or resets each PDMA transfer by setting PDMA_PAUSE or PDMA_CHRST register respectively, this bit will be cleared automatically after finishing the current transfer.
bits : 5 - 5 (1 bit)
access : read-only
Enumeration:
#0 : 0
PDMA Channel n has no request
#1 : 1
PDMA Channel n has a request
End of enumeration elements list.
REQSTS6 : PDMA Channel Request Status (Read Only)\nThis flag indicates whether channel[n] have a request or not, no matter request from software or peripheral. When PDMA controller finishes channel transfer, this bit will be cleared automatically. \nNote: If user pauses or resets each PDMA transfer by setting PDMA_PAUSE or PDMA_CHRST register respectively, this bit will be cleared automatically after finishing the current transfer.
bits : 6 - 6 (1 bit)
access : read-only
Enumeration:
#0 : 0
PDMA Channel n has no request
#1 : 1
PDMA Channel n has a request
End of enumeration elements list.
REQSTS7 : PDMA Channel Request Status (Read Only)\nThis flag indicates whether channel[n] have a request or not, no matter request from software or peripheral. When PDMA controller finishes channel transfer, this bit will be cleared automatically. \nNote: If user pauses or resets each PDMA transfer by setting PDMA_PAUSE or PDMA_CHRST register respectively, this bit will be cleared automatically after finishing the current transfer.
bits : 7 - 7 (1 bit)
access : read-only
Enumeration:
#0 : 0
PDMA Channel n has no request
#1 : 1
PDMA Channel n has a request
End of enumeration elements list.
REQSTS8 : PDMA Channel Request Status (Read Only)\nThis flag indicates whether channel[n] have a request or not, no matter request from software or peripheral. When PDMA controller finishes channel transfer, this bit will be cleared automatically. \nNote: If user pauses or resets each PDMA transfer by setting PDMA_PAUSE or PDMA_CHRST register respectively, this bit will be cleared automatically after finishing the current transfer.
bits : 8 - 8 (1 bit)
access : read-only
Enumeration:
#0 : 0
PDMA Channel n has no request
#1 : 1
PDMA Channel n has a request
End of enumeration elements list.
REQSTS9 : PDMA Channel Request Status (Read Only)\nThis flag indicates whether channel[n] have a request or not, no matter request from software or peripheral. When PDMA controller finishes channel transfer, this bit will be cleared automatically. \nNote: If user pauses or resets each PDMA transfer by setting PDMA_PAUSE or PDMA_CHRST register respectively, this bit will be cleared automatically after finishing the current transfer.
bits : 9 - 9 (1 bit)
access : read-only
Enumeration:
#0 : 0
PDMA Channel n has no request
#1 : 1
PDMA Channel n has a request
End of enumeration elements list.
REQSTS10 : PDMA Channel Request Status (Read Only)\nThis flag indicates whether channel[n] have a request or not, no matter request from software or peripheral. When PDMA controller finishes channel transfer, this bit will be cleared automatically. \nNote: If user pauses or resets each PDMA transfer by setting PDMA_PAUSE or PDMA_CHRST register respectively, this bit will be cleared automatically after finishing the current transfer.
bits : 10 - 10 (1 bit)
access : read-only
Enumeration:
#0 : 0
PDMA Channel n has no request
#1 : 1
PDMA Channel n has a request
End of enumeration elements list.
REQSTS11 : PDMA Channel Request Status (Read Only)\nThis flag indicates whether channel[n] have a request or not, no matter request from software or peripheral. When PDMA controller finishes channel transfer, this bit will be cleared automatically. \nNote: If user pauses or resets each PDMA transfer by setting PDMA_PAUSE or PDMA_CHRST register respectively, this bit will be cleared automatically after finishing the current transfer.
bits : 11 - 11 (1 bit)
access : read-only
Enumeration:
#0 : 0
PDMA Channel n has no request
#1 : 1
PDMA Channel n has a request
End of enumeration elements list.
REQSTS12 : PDMA Channel Request Status (Read Only)\nThis flag indicates whether channel[n] have a request or not, no matter request from software or peripheral. When PDMA controller finishes channel transfer, this bit will be cleared automatically. \nNote: If user pauses or resets each PDMA transfer by setting PDMA_PAUSE or PDMA_CHRST register respectively, this bit will be cleared automatically after finishing the current transfer.
bits : 12 - 12 (1 bit)
access : read-only
Enumeration:
#0 : 0
PDMA Channel n has no request
#1 : 1
PDMA Channel n has a request
End of enumeration elements list.
REQSTS13 : PDMA Channel Request Status (Read Only)\nThis flag indicates whether channel[n] have a request or not, no matter request from software or peripheral. When PDMA controller finishes channel transfer, this bit will be cleared automatically. \nNote: If user pauses or resets each PDMA transfer by setting PDMA_PAUSE or PDMA_CHRST register respectively, this bit will be cleared automatically after finishing the current transfer.
bits : 13 - 13 (1 bit)
access : read-only
Enumeration:
#0 : 0
PDMA Channel n has no request
#1 : 1
PDMA Channel n has a request
End of enumeration elements list.
REQSTS14 : PDMA Channel Request Status (Read Only)\nThis flag indicates whether channel[n] have a request or not, no matter request from software or peripheral. When PDMA controller finishes channel transfer, this bit will be cleared automatically. \nNote: If user pauses or resets each PDMA transfer by setting PDMA_PAUSE or PDMA_CHRST register respectively, this bit will be cleared automatically after finishing the current transfer.
bits : 14 - 14 (1 bit)
access : read-only
Enumeration:
#0 : 0
PDMA Channel n has no request
#1 : 1
PDMA Channel n has a request
End of enumeration elements list.
REQSTS15 : PDMA Channel Request Status (Read Only)\nThis flag indicates whether channel[n] have a request or not, no matter request from software or peripheral. When PDMA controller finishes channel transfer, this bit will be cleared automatically. \nNote: If user pauses or resets each PDMA transfer by setting PDMA_PAUSE or PDMA_CHRST register respectively, this bit will be cleared automatically after finishing the current transfer.
bits : 15 - 15 (1 bit)
access : read-only
Enumeration:
#0 : 0
PDMA Channel n has no request
#1 : 1
PDMA Channel n has a request
End of enumeration elements list.
PDMA Fixed Priority Setting Register
address_offset : 0x410 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
FPRISET0 : PDMA Fixed Priority Setting\nSet this bit to 1 to enable fixed priority level.\nWrite Operation:\nNote: This field only set to fixed priority, clear fixed priority use PDMA_PRICLR register.
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
No effect.\nCorresponding PDMA channel is round-robin priority
#1 : 1
Set PDMA channel [n] to fixed priority channel.\nCorresponding PDMA channel is fixed priority
End of enumeration elements list.
FPRISET1 : PDMA Fixed Priority Setting\nSet this bit to 1 to enable fixed priority level.\nWrite Operation:\nNote: This field only set to fixed priority, clear fixed priority use PDMA_PRICLR register.
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
No effect.\nCorresponding PDMA channel is round-robin priority
#1 : 1
Set PDMA channel [n] to fixed priority channel.\nCorresponding PDMA channel is fixed priority
End of enumeration elements list.
FPRISET2 : PDMA Fixed Priority Setting\nSet this bit to 1 to enable fixed priority level.\nWrite Operation:\nNote: This field only set to fixed priority, clear fixed priority use PDMA_PRICLR register.
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
No effect.\nCorresponding PDMA channel is round-robin priority
#1 : 1
Set PDMA channel [n] to fixed priority channel.\nCorresponding PDMA channel is fixed priority
End of enumeration elements list.
FPRISET3 : PDMA Fixed Priority Setting\nSet this bit to 1 to enable fixed priority level.\nWrite Operation:\nNote: This field only set to fixed priority, clear fixed priority use PDMA_PRICLR register.
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
No effect.\nCorresponding PDMA channel is round-robin priority
#1 : 1
Set PDMA channel [n] to fixed priority channel.\nCorresponding PDMA channel is fixed priority
End of enumeration elements list.
FPRISET4 : PDMA Fixed Priority Setting\nSet this bit to 1 to enable fixed priority level.\nWrite Operation:\nNote: This field only set to fixed priority, clear fixed priority use PDMA_PRICLR register.
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
No effect.\nCorresponding PDMA channel is round-robin priority
#1 : 1
Set PDMA channel [n] to fixed priority channel.\nCorresponding PDMA channel is fixed priority
End of enumeration elements list.
FPRISET5 : PDMA Fixed Priority Setting\nSet this bit to 1 to enable fixed priority level.\nWrite Operation:\nNote: This field only set to fixed priority, clear fixed priority use PDMA_PRICLR register.
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
No effect.\nCorresponding PDMA channel is round-robin priority
#1 : 1
Set PDMA channel [n] to fixed priority channel.\nCorresponding PDMA channel is fixed priority
End of enumeration elements list.
FPRISET6 : PDMA Fixed Priority Setting\nSet this bit to 1 to enable fixed priority level.\nWrite Operation:\nNote: This field only set to fixed priority, clear fixed priority use PDMA_PRICLR register.
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
No effect.\nCorresponding PDMA channel is round-robin priority
#1 : 1
Set PDMA channel [n] to fixed priority channel.\nCorresponding PDMA channel is fixed priority
End of enumeration elements list.
FPRISET7 : PDMA Fixed Priority Setting\nSet this bit to 1 to enable fixed priority level.\nWrite Operation:\nNote: This field only set to fixed priority, clear fixed priority use PDMA_PRICLR register.
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
No effect.\nCorresponding PDMA channel is round-robin priority
#1 : 1
Set PDMA channel [n] to fixed priority channel.\nCorresponding PDMA channel is fixed priority
End of enumeration elements list.
FPRISET8 : PDMA Fixed Priority Setting\nSet this bit to 1 to enable fixed priority level.\nWrite Operation:\nNote: This field only set to fixed priority, clear fixed priority use PDMA_PRICLR register.
bits : 8 - 8 (1 bit)
access : read-write
Enumeration:
#0 : 0
No effect.\nCorresponding PDMA channel is round-robin priority
#1 : 1
Set PDMA channel [n] to fixed priority channel.\nCorresponding PDMA channel is fixed priority
End of enumeration elements list.
FPRISET9 : PDMA Fixed Priority Setting\nSet this bit to 1 to enable fixed priority level.\nWrite Operation:\nNote: This field only set to fixed priority, clear fixed priority use PDMA_PRICLR register.
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
No effect.\nCorresponding PDMA channel is round-robin priority
#1 : 1
Set PDMA channel [n] to fixed priority channel.\nCorresponding PDMA channel is fixed priority
End of enumeration elements list.
FPRISET10 : PDMA Fixed Priority Setting\nSet this bit to 1 to enable fixed priority level.\nWrite Operation:\nNote: This field only set to fixed priority, clear fixed priority use PDMA_PRICLR register.
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
No effect.\nCorresponding PDMA channel is round-robin priority
#1 : 1
Set PDMA channel [n] to fixed priority channel.\nCorresponding PDMA channel is fixed priority
End of enumeration elements list.
FPRISET11 : PDMA Fixed Priority Setting\nSet this bit to 1 to enable fixed priority level.\nWrite Operation:\nNote: This field only set to fixed priority, clear fixed priority use PDMA_PRICLR register.
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
No effect.\nCorresponding PDMA channel is round-robin priority
#1 : 1
Set PDMA channel [n] to fixed priority channel.\nCorresponding PDMA channel is fixed priority
End of enumeration elements list.
FPRISET12 : PDMA Fixed Priority Setting\nSet this bit to 1 to enable fixed priority level.\nWrite Operation:\nNote: This field only set to fixed priority, clear fixed priority use PDMA_PRICLR register.
bits : 12 - 12 (1 bit)
access : read-write
Enumeration:
#0 : 0
No effect.\nCorresponding PDMA channel is round-robin priority
#1 : 1
Set PDMA channel [n] to fixed priority channel.\nCorresponding PDMA channel is fixed priority
End of enumeration elements list.
FPRISET13 : PDMA Fixed Priority Setting\nSet this bit to 1 to enable fixed priority level.\nWrite Operation:\nNote: This field only set to fixed priority, clear fixed priority use PDMA_PRICLR register.
bits : 13 - 13 (1 bit)
access : read-write
Enumeration:
#0 : 0
No effect.\nCorresponding PDMA channel is round-robin priority
#1 : 1
Set PDMA channel [n] to fixed priority channel.\nCorresponding PDMA channel is fixed priority
End of enumeration elements list.
FPRISET14 : PDMA Fixed Priority Setting\nSet this bit to 1 to enable fixed priority level.\nWrite Operation:\nNote: This field only set to fixed priority, clear fixed priority use PDMA_PRICLR register.
bits : 14 - 14 (1 bit)
access : read-write
Enumeration:
#0 : 0
No effect.\nCorresponding PDMA channel is round-robin priority
#1 : 1
Set PDMA channel [n] to fixed priority channel.\nCorresponding PDMA channel is fixed priority
End of enumeration elements list.
FPRISET15 : PDMA Fixed Priority Setting\nSet this bit to 1 to enable fixed priority level.\nWrite Operation:\nNote: This field only set to fixed priority, clear fixed priority use PDMA_PRICLR register.
bits : 15 - 15 (1 bit)
access : read-write
Enumeration:
#0 : 0
No effect.\nCorresponding PDMA channel is round-robin priority
#1 : 1
Set PDMA channel [n] to fixed priority channel.\nCorresponding PDMA channel is fixed priority
End of enumeration elements list.
PDMA Fixed Priority Clear Register
address_offset : 0x414 Bytes (0x0)
access : write-only
reset_value : 0x0
reset_Mask : 0x0
FPRICLR0 : PDMA Fixed Priority Clear Bits (Write Only)\nSet this bit to 1 to clear fixed priority level.\nNote: User can read PDMA_PRISET register to know the channel priority.
bits : 0 - 0 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Clear PDMA channel [n] fixed priority setting
End of enumeration elements list.
FPRICLR1 : PDMA Fixed Priority Clear Bits (Write Only)\nSet this bit to 1 to clear fixed priority level.\nNote: User can read PDMA_PRISET register to know the channel priority.
bits : 1 - 1 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Clear PDMA channel [n] fixed priority setting
End of enumeration elements list.
FPRICLR2 : PDMA Fixed Priority Clear Bits (Write Only)\nSet this bit to 1 to clear fixed priority level.\nNote: User can read PDMA_PRISET register to know the channel priority.
bits : 2 - 2 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Clear PDMA channel [n] fixed priority setting
End of enumeration elements list.
FPRICLR3 : PDMA Fixed Priority Clear Bits (Write Only)\nSet this bit to 1 to clear fixed priority level.\nNote: User can read PDMA_PRISET register to know the channel priority.
bits : 3 - 3 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Clear PDMA channel [n] fixed priority setting
End of enumeration elements list.
FPRICLR4 : PDMA Fixed Priority Clear Bits (Write Only)\nSet this bit to 1 to clear fixed priority level.\nNote: User can read PDMA_PRISET register to know the channel priority.
bits : 4 - 4 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Clear PDMA channel [n] fixed priority setting
End of enumeration elements list.
FPRICLR5 : PDMA Fixed Priority Clear Bits (Write Only)\nSet this bit to 1 to clear fixed priority level.\nNote: User can read PDMA_PRISET register to know the channel priority.
bits : 5 - 5 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Clear PDMA channel [n] fixed priority setting
End of enumeration elements list.
FPRICLR6 : PDMA Fixed Priority Clear Bits (Write Only)\nSet this bit to 1 to clear fixed priority level.\nNote: User can read PDMA_PRISET register to know the channel priority.
bits : 6 - 6 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Clear PDMA channel [n] fixed priority setting
End of enumeration elements list.
FPRICLR7 : PDMA Fixed Priority Clear Bits (Write Only)\nSet this bit to 1 to clear fixed priority level.\nNote: User can read PDMA_PRISET register to know the channel priority.
bits : 7 - 7 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Clear PDMA channel [n] fixed priority setting
End of enumeration elements list.
FPRICLR8 : PDMA Fixed Priority Clear Bits (Write Only)\nSet this bit to 1 to clear fixed priority level.\nNote: User can read PDMA_PRISET register to know the channel priority.
bits : 8 - 8 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Clear PDMA channel [n] fixed priority setting
End of enumeration elements list.
FPRICLR9 : PDMA Fixed Priority Clear Bits (Write Only)\nSet this bit to 1 to clear fixed priority level.\nNote: User can read PDMA_PRISET register to know the channel priority.
bits : 9 - 9 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Clear PDMA channel [n] fixed priority setting
End of enumeration elements list.
FPRICLR10 : PDMA Fixed Priority Clear Bits (Write Only)\nSet this bit to 1 to clear fixed priority level.\nNote: User can read PDMA_PRISET register to know the channel priority.
bits : 10 - 10 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Clear PDMA channel [n] fixed priority setting
End of enumeration elements list.
FPRICLR11 : PDMA Fixed Priority Clear Bits (Write Only)\nSet this bit to 1 to clear fixed priority level.\nNote: User can read PDMA_PRISET register to know the channel priority.
bits : 11 - 11 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Clear PDMA channel [n] fixed priority setting
End of enumeration elements list.
FPRICLR12 : PDMA Fixed Priority Clear Bits (Write Only)\nSet this bit to 1 to clear fixed priority level.\nNote: User can read PDMA_PRISET register to know the channel priority.
bits : 12 - 12 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Clear PDMA channel [n] fixed priority setting
End of enumeration elements list.
FPRICLR13 : PDMA Fixed Priority Clear Bits (Write Only)\nSet this bit to 1 to clear fixed priority level.\nNote: User can read PDMA_PRISET register to know the channel priority.
bits : 13 - 13 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Clear PDMA channel [n] fixed priority setting
End of enumeration elements list.
FPRICLR14 : PDMA Fixed Priority Clear Bits (Write Only)\nSet this bit to 1 to clear fixed priority level.\nNote: User can read PDMA_PRISET register to know the channel priority.
bits : 14 - 14 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Clear PDMA channel [n] fixed priority setting
End of enumeration elements list.
FPRICLR15 : PDMA Fixed Priority Clear Bits (Write Only)\nSet this bit to 1 to clear fixed priority level.\nNote: User can read PDMA_PRISET register to know the channel priority.
bits : 15 - 15 (1 bit)
access : write-only
Enumeration:
#0 : 0
No effect
#1 : 1
Clear PDMA channel [n] fixed priority setting
End of enumeration elements list.
PDMA Interrupt Enable Register
address_offset : 0x418 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
INTEN0 : PDMA Interrupt Enable Bits\nThis field is used to enable PDMA channel[n] interrupt.
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel n interrupt Disabled
#1 : 1
PDMA channel n interrupt Enabled.Note: The interrupt flag is time-out, abort, transfer done and align
End of enumeration elements list.
INTEN1 : PDMA Interrupt Enable Bits\nThis field is used to enable PDMA channel[n] interrupt.
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel n interrupt Disabled
#1 : 1
PDMA channel n interrupt Enabled.Note: The interrupt flag is time-out, abort, transfer done and align
End of enumeration elements list.
INTEN2 : PDMA Interrupt Enable Bits\nThis field is used to enable PDMA channel[n] interrupt.
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel n interrupt Disabled
#1 : 1
PDMA channel n interrupt Enabled.Note: The interrupt flag is time-out, abort, transfer done and align
End of enumeration elements list.
INTEN3 : PDMA Interrupt Enable Bits\nThis field is used to enable PDMA channel[n] interrupt.
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel n interrupt Disabled
#1 : 1
PDMA channel n interrupt Enabled.Note: The interrupt flag is time-out, abort, transfer done and align
End of enumeration elements list.
INTEN4 : PDMA Interrupt Enable Bits\nThis field is used to enable PDMA channel[n] interrupt.
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel n interrupt Disabled
#1 : 1
PDMA channel n interrupt Enabled.Note: The interrupt flag is time-out, abort, transfer done and align
End of enumeration elements list.
INTEN5 : PDMA Interrupt Enable Bits\nThis field is used to enable PDMA channel[n] interrupt.
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel n interrupt Disabled
#1 : 1
PDMA channel n interrupt Enabled.Note: The interrupt flag is time-out, abort, transfer done and align
End of enumeration elements list.
INTEN6 : PDMA Interrupt Enable Bits\nThis field is used to enable PDMA channel[n] interrupt.
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel n interrupt Disabled
#1 : 1
PDMA channel n interrupt Enabled.Note: The interrupt flag is time-out, abort, transfer done and align
End of enumeration elements list.
INTEN7 : PDMA Interrupt Enable Bits\nThis field is used to enable PDMA channel[n] interrupt.
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel n interrupt Disabled
#1 : 1
PDMA channel n interrupt Enabled.Note: The interrupt flag is time-out, abort, transfer done and align
End of enumeration elements list.
INTEN8 : PDMA Interrupt Enable Bits\nThis field is used to enable PDMA channel[n] interrupt.
bits : 8 - 8 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel n interrupt Disabled
#1 : 1
PDMA channel n interrupt Enabled.Note: The interrupt flag is time-out, abort, transfer done and align
End of enumeration elements list.
INTEN9 : PDMA Interrupt Enable Bits\nThis field is used to enable PDMA channel[n] interrupt.
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel n interrupt Disabled
#1 : 1
PDMA channel n interrupt Enabled.Note: The interrupt flag is time-out, abort, transfer done and align
End of enumeration elements list.
INTEN10 : PDMA Interrupt Enable Bits\nThis field is used to enable PDMA channel[n] interrupt.
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel n interrupt Disabled
#1 : 1
PDMA channel n interrupt Enabled.Note: The interrupt flag is time-out, abort, transfer done and align
End of enumeration elements list.
INTEN11 : PDMA Interrupt Enable Bits\nThis field is used to enable PDMA channel[n] interrupt.
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel n interrupt Disabled
#1 : 1
PDMA channel n interrupt Enabled.Note: The interrupt flag is time-out, abort, transfer done and align
End of enumeration elements list.
INTEN12 : PDMA Interrupt Enable Bits\nThis field is used to enable PDMA channel[n] interrupt.
bits : 12 - 12 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel n interrupt Disabled
#1 : 1
PDMA channel n interrupt Enabled.Note: The interrupt flag is time-out, abort, transfer done and align
End of enumeration elements list.
INTEN13 : PDMA Interrupt Enable Bits\nThis field is used to enable PDMA channel[n] interrupt.
bits : 13 - 13 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel n interrupt Disabled
#1 : 1
PDMA channel n interrupt Enabled.Note: The interrupt flag is time-out, abort, transfer done and align
End of enumeration elements list.
INTEN14 : PDMA Interrupt Enable Bits\nThis field is used to enable PDMA channel[n] interrupt.
bits : 14 - 14 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel n interrupt Disabled
#1 : 1
PDMA channel n interrupt Enabled.Note: The interrupt flag is time-out, abort, transfer done and align
End of enumeration elements list.
INTEN15 : PDMA Interrupt Enable Bits\nThis field is used to enable PDMA channel[n] interrupt.
bits : 15 - 15 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel n interrupt Disabled
#1 : 1
PDMA channel n interrupt Enabled.Note: The interrupt flag is time-out, abort, transfer done and align
End of enumeration elements list.
PDMA Interrupt Status Register
address_offset : 0x41C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ABTIF : PDMA Read/Write Target Abort Interrupt Flag (Read Only)
This bit indicates that PDMA has target abort error Software can read PDMA_ABTSTS register to find which channel has target abort error.
bits : 0 - 0 (1 bit)
access : read-only
Enumeration:
#0 : 0
No AHB bus ERROR response received
#1 : 1
AHB bus ERROR response received
End of enumeration elements list.
TDIF : Transfer Done Interrupt Flag (Read Only)
This bit indicates that PDMA controller has finished transmission User can read PDMA_TDSTS register to indicate which channel finished transfer.
bits : 1 - 1 (1 bit)
access : read-only
Enumeration:
#0 : 0
Not finished yet
#1 : 1
PDMA channel has finished transmission
End of enumeration elements list.
ALIGNF : Transfer Alignment Interrupt Flag (Read Only)
bits : 2 - 2 (1 bit)
access : read-only
Enumeration:
#0 : 0
PDMA channel source address and destination address both follow transfer width setting
#1 : 1
PDMA channel source address or destination address is not follow transfer width setting
End of enumeration elements list.
REQTOF0 : Request Time-out Flag for Channel 0\nThis flag indicates that PDMA controller has waited peripheral request for a period defined by PDMA_TOC0, user can write 1 to clear these bits.\nNote: Please disable time-out function before clear this bit.
bits : 8 - 8 (1 bit)
access : read-write
Enumeration:
#0 : 0
No request time-out
#1 : 1
Peripheral request time-out
End of enumeration elements list.
REQTOF1 : Request Time-out Flag for Channel 1\nThis flag indicates that PDMA controller has waited peripheral request for a period defined by PDMA_TOC1, user can write 1 to clear these bits.\nNote: Please disable time-out function before clear this bit.
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
No request time-out
#1 : 1
Peripheral request time-out
End of enumeration elements list.
PDMA Channel Read/Write Target Abort Flag Register
address_offset : 0x420 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ABTIF0 : PDMA Read/Write Target Abort Interrupt Status Flag
This bit indicates which PDMA controller has target abort error User can write 1 to clear these bits.
Note: If channel n target abort, REQSRCn should set 0 to disable peripheral request.
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
No AHB bus ERROR response received when channel n transfer
#1 : 1
AHB bus ERROR response received when channel n transfer
End of enumeration elements list.
ABTIF1 : PDMA Read/Write Target Abort Interrupt Status Flag
This bit indicates which PDMA controller has target abort error User can write 1 to clear these bits.
Note: If channel n target abort, REQSRCn should set 0 to disable peripheral request.
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
No AHB bus ERROR response received when channel n transfer
#1 : 1
AHB bus ERROR response received when channel n transfer
End of enumeration elements list.
ABTIF2 : PDMA Read/Write Target Abort Interrupt Status Flag
This bit indicates which PDMA controller has target abort error User can write 1 to clear these bits.
Note: If channel n target abort, REQSRCn should set 0 to disable peripheral request.
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
No AHB bus ERROR response received when channel n transfer
#1 : 1
AHB bus ERROR response received when channel n transfer
End of enumeration elements list.
ABTIF3 : PDMA Read/Write Target Abort Interrupt Status Flag
This bit indicates which PDMA controller has target abort error User can write 1 to clear these bits.
Note: If channel n target abort, REQSRCn should set 0 to disable peripheral request.
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
No AHB bus ERROR response received when channel n transfer
#1 : 1
AHB bus ERROR response received when channel n transfer
End of enumeration elements list.
ABTIF4 : PDMA Read/Write Target Abort Interrupt Status Flag
This bit indicates which PDMA controller has target abort error User can write 1 to clear these bits.
Note: If channel n target abort, REQSRCn should set 0 to disable peripheral request.
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
No AHB bus ERROR response received when channel n transfer
#1 : 1
AHB bus ERROR response received when channel n transfer
End of enumeration elements list.
ABTIF5 : PDMA Read/Write Target Abort Interrupt Status Flag
This bit indicates which PDMA controller has target abort error User can write 1 to clear these bits.
Note: If channel n target abort, REQSRCn should set 0 to disable peripheral request.
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
No AHB bus ERROR response received when channel n transfer
#1 : 1
AHB bus ERROR response received when channel n transfer
End of enumeration elements list.
ABTIF6 : PDMA Read/Write Target Abort Interrupt Status Flag
This bit indicates which PDMA controller has target abort error User can write 1 to clear these bits.
Note: If channel n target abort, REQSRCn should set 0 to disable peripheral request.
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
No AHB bus ERROR response received when channel n transfer
#1 : 1
AHB bus ERROR response received when channel n transfer
End of enumeration elements list.
ABTIF7 : PDMA Read/Write Target Abort Interrupt Status Flag
This bit indicates which PDMA controller has target abort error User can write 1 to clear these bits.
Note: If channel n target abort, REQSRCn should set 0 to disable peripheral request.
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
No AHB bus ERROR response received when channel n transfer
#1 : 1
AHB bus ERROR response received when channel n transfer
End of enumeration elements list.
ABTIF8 : PDMA Read/Write Target Abort Interrupt Status Flag
This bit indicates which PDMA controller has target abort error User can write 1 to clear these bits.
Note: If channel n target abort, REQSRCn should set 0 to disable peripheral request.
bits : 8 - 8 (1 bit)
access : read-write
Enumeration:
#0 : 0
No AHB bus ERROR response received when channel n transfer
#1 : 1
AHB bus ERROR response received when channel n transfer
End of enumeration elements list.
ABTIF9 : PDMA Read/Write Target Abort Interrupt Status Flag
This bit indicates which PDMA controller has target abort error User can write 1 to clear these bits.
Note: If channel n target abort, REQSRCn should set 0 to disable peripheral request.
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
No AHB bus ERROR response received when channel n transfer
#1 : 1
AHB bus ERROR response received when channel n transfer
End of enumeration elements list.
ABTIF10 : PDMA Read/Write Target Abort Interrupt Status Flag
This bit indicates which PDMA controller has target abort error User can write 1 to clear these bits.
Note: If channel n target abort, REQSRCn should set 0 to disable peripheral request.
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
No AHB bus ERROR response received when channel n transfer
#1 : 1
AHB bus ERROR response received when channel n transfer
End of enumeration elements list.
ABTIF11 : PDMA Read/Write Target Abort Interrupt Status Flag
This bit indicates which PDMA controller has target abort error User can write 1 to clear these bits.
Note: If channel n target abort, REQSRCn should set 0 to disable peripheral request.
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
No AHB bus ERROR response received when channel n transfer
#1 : 1
AHB bus ERROR response received when channel n transfer
End of enumeration elements list.
ABTIF12 : PDMA Read/Write Target Abort Interrupt Status Flag
This bit indicates which PDMA controller has target abort error User can write 1 to clear these bits.
Note: If channel n target abort, REQSRCn should set 0 to disable peripheral request.
bits : 12 - 12 (1 bit)
access : read-write
Enumeration:
#0 : 0
No AHB bus ERROR response received when channel n transfer
#1 : 1
AHB bus ERROR response received when channel n transfer
End of enumeration elements list.
ABTIF13 : PDMA Read/Write Target Abort Interrupt Status Flag
This bit indicates which PDMA controller has target abort error User can write 1 to clear these bits.
Note: If channel n target abort, REQSRCn should set 0 to disable peripheral request.
bits : 13 - 13 (1 bit)
access : read-write
Enumeration:
#0 : 0
No AHB bus ERROR response received when channel n transfer
#1 : 1
AHB bus ERROR response received when channel n transfer
End of enumeration elements list.
ABTIF14 : PDMA Read/Write Target Abort Interrupt Status Flag
This bit indicates which PDMA controller has target abort error User can write 1 to clear these bits.
Note: If channel n target abort, REQSRCn should set 0 to disable peripheral request.
bits : 14 - 14 (1 bit)
access : read-write
Enumeration:
#0 : 0
No AHB bus ERROR response received when channel n transfer
#1 : 1
AHB bus ERROR response received when channel n transfer
End of enumeration elements list.
ABTIF15 : PDMA Read/Write Target Abort Interrupt Status Flag
This bit indicates which PDMA controller has target abort error User can write 1 to clear these bits.
Note: If channel n target abort, REQSRCn should set 0 to disable peripheral request.
bits : 15 - 15 (1 bit)
access : read-write
Enumeration:
#0 : 0
No AHB bus ERROR response received when channel n transfer
#1 : 1
AHB bus ERROR response received when channel n transfer
End of enumeration elements list.
PDMA Channel Transfer Done Flag Register
address_offset : 0x424 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TDIF0 : Transfer Done Flag\nThis bit indicates whether PDMA controller channel transfer has been finished or not, user can write 1 to clear these bits.
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel transfer has not finished
#1 : 1
PDMA channel has finished transmission
End of enumeration elements list.
TDIF1 : Transfer Done Flag\nThis bit indicates whether PDMA controller channel transfer has been finished or not, user can write 1 to clear these bits.
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel transfer has not finished
#1 : 1
PDMA channel has finished transmission
End of enumeration elements list.
TDIF2 : Transfer Done Flag\nThis bit indicates whether PDMA controller channel transfer has been finished or not, user can write 1 to clear these bits.
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel transfer has not finished
#1 : 1
PDMA channel has finished transmission
End of enumeration elements list.
TDIF3 : Transfer Done Flag\nThis bit indicates whether PDMA controller channel transfer has been finished or not, user can write 1 to clear these bits.
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel transfer has not finished
#1 : 1
PDMA channel has finished transmission
End of enumeration elements list.
TDIF4 : Transfer Done Flag\nThis bit indicates whether PDMA controller channel transfer has been finished or not, user can write 1 to clear these bits.
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel transfer has not finished
#1 : 1
PDMA channel has finished transmission
End of enumeration elements list.
TDIF5 : Transfer Done Flag\nThis bit indicates whether PDMA controller channel transfer has been finished or not, user can write 1 to clear these bits.
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel transfer has not finished
#1 : 1
PDMA channel has finished transmission
End of enumeration elements list.
TDIF6 : Transfer Done Flag\nThis bit indicates whether PDMA controller channel transfer has been finished or not, user can write 1 to clear these bits.
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel transfer has not finished
#1 : 1
PDMA channel has finished transmission
End of enumeration elements list.
TDIF7 : Transfer Done Flag\nThis bit indicates whether PDMA controller channel transfer has been finished or not, user can write 1 to clear these bits.
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel transfer has not finished
#1 : 1
PDMA channel has finished transmission
End of enumeration elements list.
TDIF8 : Transfer Done Flag\nThis bit indicates whether PDMA controller channel transfer has been finished or not, user can write 1 to clear these bits.
bits : 8 - 8 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel transfer has not finished
#1 : 1
PDMA channel has finished transmission
End of enumeration elements list.
TDIF9 : Transfer Done Flag\nThis bit indicates whether PDMA controller channel transfer has been finished or not, user can write 1 to clear these bits.
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel transfer has not finished
#1 : 1
PDMA channel has finished transmission
End of enumeration elements list.
TDIF10 : Transfer Done Flag\nThis bit indicates whether PDMA controller channel transfer has been finished or not, user can write 1 to clear these bits.
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel transfer has not finished
#1 : 1
PDMA channel has finished transmission
End of enumeration elements list.
TDIF11 : Transfer Done Flag\nThis bit indicates whether PDMA controller channel transfer has been finished or not, user can write 1 to clear these bits.
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel transfer has not finished
#1 : 1
PDMA channel has finished transmission
End of enumeration elements list.
TDIF12 : Transfer Done Flag\nThis bit indicates whether PDMA controller channel transfer has been finished or not, user can write 1 to clear these bits.
bits : 12 - 12 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel transfer has not finished
#1 : 1
PDMA channel has finished transmission
End of enumeration elements list.
TDIF13 : Transfer Done Flag\nThis bit indicates whether PDMA controller channel transfer has been finished or not, user can write 1 to clear these bits.
bits : 13 - 13 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel transfer has not finished
#1 : 1
PDMA channel has finished transmission
End of enumeration elements list.
TDIF14 : Transfer Done Flag\nThis bit indicates whether PDMA controller channel transfer has been finished or not, user can write 1 to clear these bits.
bits : 14 - 14 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel transfer has not finished
#1 : 1
PDMA channel has finished transmission
End of enumeration elements list.
TDIF15 : Transfer Done Flag\nThis bit indicates whether PDMA controller channel transfer has been finished or not, user can write 1 to clear these bits.
bits : 15 - 15 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel transfer has not finished
#1 : 1
PDMA channel has finished transmission
End of enumeration elements list.
PDMA Transfer Alignment Status Register
address_offset : 0x428 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ALIGN0 : Transfer Alignment Flag\nNote: Source address and destination address should be alignment.
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel source address and destination address both follow transfer width setting
#1 : 1
PDMA channel source address or destination address is not follow transfer width setting
End of enumeration elements list.
ALIGN1 : Transfer Alignment Flag\nNote: Source address and destination address should be alignment.
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel source address and destination address both follow transfer width setting
#1 : 1
PDMA channel source address or destination address is not follow transfer width setting
End of enumeration elements list.
ALIGN2 : Transfer Alignment Flag\nNote: Source address and destination address should be alignment.
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel source address and destination address both follow transfer width setting
#1 : 1
PDMA channel source address or destination address is not follow transfer width setting
End of enumeration elements list.
ALIGN3 : Transfer Alignment Flag\nNote: Source address and destination address should be alignment.
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel source address and destination address both follow transfer width setting
#1 : 1
PDMA channel source address or destination address is not follow transfer width setting
End of enumeration elements list.
ALIGN4 : Transfer Alignment Flag\nNote: Source address and destination address should be alignment.
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel source address and destination address both follow transfer width setting
#1 : 1
PDMA channel source address or destination address is not follow transfer width setting
End of enumeration elements list.
ALIGN5 : Transfer Alignment Flag\nNote: Source address and destination address should be alignment.
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel source address and destination address both follow transfer width setting
#1 : 1
PDMA channel source address or destination address is not follow transfer width setting
End of enumeration elements list.
ALIGN6 : Transfer Alignment Flag\nNote: Source address and destination address should be alignment.
bits : 6 - 6 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel source address and destination address both follow transfer width setting
#1 : 1
PDMA channel source address or destination address is not follow transfer width setting
End of enumeration elements list.
ALIGN7 : Transfer Alignment Flag\nNote: Source address and destination address should be alignment.
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel source address and destination address both follow transfer width setting
#1 : 1
PDMA channel source address or destination address is not follow transfer width setting
End of enumeration elements list.
ALIGN8 : Transfer Alignment Flag\nNote: Source address and destination address should be alignment.
bits : 8 - 8 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel source address and destination address both follow transfer width setting
#1 : 1
PDMA channel source address or destination address is not follow transfer width setting
End of enumeration elements list.
ALIGN9 : Transfer Alignment Flag\nNote: Source address and destination address should be alignment.
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel source address and destination address both follow transfer width setting
#1 : 1
PDMA channel source address or destination address is not follow transfer width setting
End of enumeration elements list.
ALIGN10 : Transfer Alignment Flag\nNote: Source address and destination address should be alignment.
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel source address and destination address both follow transfer width setting
#1 : 1
PDMA channel source address or destination address is not follow transfer width setting
End of enumeration elements list.
ALIGN11 : Transfer Alignment Flag\nNote: Source address and destination address should be alignment.
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel source address and destination address both follow transfer width setting
#1 : 1
PDMA channel source address or destination address is not follow transfer width setting
End of enumeration elements list.
ALIGN12 : Transfer Alignment Flag\nNote: Source address and destination address should be alignment.
bits : 12 - 12 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel source address and destination address both follow transfer width setting
#1 : 1
PDMA channel source address or destination address is not follow transfer width setting
End of enumeration elements list.
ALIGN13 : Transfer Alignment Flag\nNote: Source address and destination address should be alignment.
bits : 13 - 13 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel source address and destination address both follow transfer width setting
#1 : 1
PDMA channel source address or destination address is not follow transfer width setting
End of enumeration elements list.
ALIGN14 : Transfer Alignment Flag\nNote: Source address and destination address should be alignment.
bits : 14 - 14 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel source address and destination address both follow transfer width setting
#1 : 1
PDMA channel source address or destination address is not follow transfer width setting
End of enumeration elements list.
ALIGN15 : Transfer Alignment Flag\nNote: Source address and destination address should be alignment.
bits : 15 - 15 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA channel source address and destination address both follow transfer width setting
#1 : 1
PDMA channel source address or destination address is not follow transfer width setting
End of enumeration elements list.
PDMA Transfer Active Flag Register
address_offset : 0x42C Bytes (0x0)
access : read-only
reset_value : 0x0
reset_Mask : 0x0
TXACTF0 : Transfer on Active Flag (Read Only)\nThis bit indicates which PDMA channel is in active.
bits : 0 - 0 (1 bit)
access : read-only
Enumeration:
#0 : 0
PDMA channel is not finished
#1 : 1
PDMA channel is active
End of enumeration elements list.
TXACTF1 : Transfer on Active Flag (Read Only)\nThis bit indicates which PDMA channel is in active.
bits : 1 - 1 (1 bit)
access : read-only
Enumeration:
#0 : 0
PDMA channel is not finished
#1 : 1
PDMA channel is active
End of enumeration elements list.
TXACTF2 : Transfer on Active Flag (Read Only)\nThis bit indicates which PDMA channel is in active.
bits : 2 - 2 (1 bit)
access : read-only
Enumeration:
#0 : 0
PDMA channel is not finished
#1 : 1
PDMA channel is active
End of enumeration elements list.
TXACTF3 : Transfer on Active Flag (Read Only)\nThis bit indicates which PDMA channel is in active.
bits : 3 - 3 (1 bit)
access : read-only
Enumeration:
#0 : 0
PDMA channel is not finished
#1 : 1
PDMA channel is active
End of enumeration elements list.
TXACTF4 : Transfer on Active Flag (Read Only)\nThis bit indicates which PDMA channel is in active.
bits : 4 - 4 (1 bit)
access : read-only
Enumeration:
#0 : 0
PDMA channel is not finished
#1 : 1
PDMA channel is active
End of enumeration elements list.
TXACTF5 : Transfer on Active Flag (Read Only)\nThis bit indicates which PDMA channel is in active.
bits : 5 - 5 (1 bit)
access : read-only
Enumeration:
#0 : 0
PDMA channel is not finished
#1 : 1
PDMA channel is active
End of enumeration elements list.
TXACTF6 : Transfer on Active Flag (Read Only)\nThis bit indicates which PDMA channel is in active.
bits : 6 - 6 (1 bit)
access : read-only
Enumeration:
#0 : 0
PDMA channel is not finished
#1 : 1
PDMA channel is active
End of enumeration elements list.
TXACTF7 : Transfer on Active Flag (Read Only)\nThis bit indicates which PDMA channel is in active.
bits : 7 - 7 (1 bit)
access : read-only
Enumeration:
#0 : 0
PDMA channel is not finished
#1 : 1
PDMA channel is active
End of enumeration elements list.
TXACTF8 : Transfer on Active Flag (Read Only)\nThis bit indicates which PDMA channel is in active.
bits : 8 - 8 (1 bit)
access : read-only
Enumeration:
#0 : 0
PDMA channel is not finished
#1 : 1
PDMA channel is active
End of enumeration elements list.
TXACTF9 : Transfer on Active Flag (Read Only)\nThis bit indicates which PDMA channel is in active.
bits : 9 - 9 (1 bit)
access : read-only
Enumeration:
#0 : 0
PDMA channel is not finished
#1 : 1
PDMA channel is active
End of enumeration elements list.
TXACTF10 : Transfer on Active Flag (Read Only)\nThis bit indicates which PDMA channel is in active.
bits : 10 - 10 (1 bit)
access : read-only
Enumeration:
#0 : 0
PDMA channel is not finished
#1 : 1
PDMA channel is active
End of enumeration elements list.
TXACTF11 : Transfer on Active Flag (Read Only)\nThis bit indicates which PDMA channel is in active.
bits : 11 - 11 (1 bit)
access : read-only
Enumeration:
#0 : 0
PDMA channel is not finished
#1 : 1
PDMA channel is active
End of enumeration elements list.
TXACTF12 : Transfer on Active Flag (Read Only)\nThis bit indicates which PDMA channel is in active.
bits : 12 - 12 (1 bit)
access : read-only
Enumeration:
#0 : 0
PDMA channel is not finished
#1 : 1
PDMA channel is active
End of enumeration elements list.
TXACTF13 : Transfer on Active Flag (Read Only)\nThis bit indicates which PDMA channel is in active.
bits : 13 - 13 (1 bit)
access : read-only
Enumeration:
#0 : 0
PDMA channel is not finished
#1 : 1
PDMA channel is active
End of enumeration elements list.
TXACTF14 : Transfer on Active Flag (Read Only)\nThis bit indicates which PDMA channel is in active.
bits : 14 - 14 (1 bit)
access : read-only
Enumeration:
#0 : 0
PDMA channel is not finished
#1 : 1
PDMA channel is active
End of enumeration elements list.
TXACTF15 : Transfer on Active Flag (Read Only)\nThis bit indicates which PDMA channel is in active.
bits : 15 - 15 (1 bit)
access : read-only
Enumeration:
#0 : 0
PDMA channel is not finished
#1 : 1
PDMA channel is active
End of enumeration elements list.
PDMA Time-out Prescaler Register
address_offset : 0x430 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TOUTPSC0 : PDMA Channel 0 Time-out Clock Source Prescaler Bits
bits : 0 - 2 (3 bit)
access : read-write
Enumeration:
#000 : 0
PDMA channel 0 time-out clock source is HCLK/28
#001 : 1
PDMA channel 0 time-out clock source is HCLK/29
#010 : 2
PDMA channel 0 time-out clock source is HCLK/210
#011 : 3
PDMA channel 0 time-out clock source is HCLK/211
#100 : 4
PDMA channel 0 time-out clock source is HCLK/212
#101 : 5
PDMA channel 0 time-out clock source is HCLK/213
#110 : 6
PDMA channel 0 time-out clock source is HCLK/214
#111 : 7
PDMA channel 0 time-out clock source is HCLK/215
End of enumeration elements list.
TOUTPSC1 : PDMA Channel 1 Time-out Clock Source Prescaler Bits
bits : 4 - 6 (3 bit)
access : read-write
Enumeration:
#000 : 0
PDMA channel 1 time-out clock source is HCLK/28
#001 : 1
PDMA channel 1 time-out clock source is HCLK/29
#010 : 2
PDMA channel 1 time-out clock source is HCLK/210
#011 : 3
PDMA channel 1 time-out clock source is HCLK/211
#100 : 4
PDMA channel 1 time-out clock source is HCLK/212
#101 : 5
PDMA channel 1 time-out clock source is HCLK/213
#110 : 6
PDMA channel 1 time-out clock source is HCLK/214
#111 : 7
PDMA channel 1 time-out clock source is HCLK/215
End of enumeration elements list.
PDMA Time-out Enable Register
address_offset : 0x434 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TOUTEN0 : PDMA Time-out Enable Bits
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA Channel n time-out function Disabled
#1 : 1
PDMA Channel n time-out function Enabled
End of enumeration elements list.
TOUTEN1 : PDMA Time-out Enable Bits
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA Channel n time-out function Disabled
#1 : 1
PDMA Channel n time-out function Enabled
End of enumeration elements list.
PDMA Time-out Interrupt Enable Register
address_offset : 0x438 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TOUTIEN0 : PDMA Time-out Interrupt Enable Bits
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA Channel n time-out interrupt Disabled
#1 : 1
PDMA Channel n time-out interrupt Enabled
End of enumeration elements list.
TOUTIEN1 : PDMA Time-out Interrupt Enable Bits
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
PDMA Channel n time-out interrupt Disabled
#1 : 1
PDMA Channel n time-out interrupt Enabled
End of enumeration elements list.
PDMA Scatter-gather Descriptor Table Base Address Register
address_offset : 0x43C Bytes (0x0)
size : -1 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SCATBA : PDMA Scatter-gather Descriptor Table Address\nIn Scatter-Gather mode, this is the base address for calculating the next link - list address. The next link address equation is \nNote: Only useful in Scatter-Gather mode.
bits : 16 - 31 (16 bit)
access : read-write
PDMA Time-out Counter Ch1 and Ch0 Register
address_offset : 0x440 Bytes (0x0)
size : -1 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TOC0 : Time-out Counter for Channel 0\nThis controls the period of time-out function for channel 0. The calculation unit is based on TOUTPSC0 (PDMA_TOUTPSC[2:0]) clock.
bits : 0 - 15 (16 bit)
access : read-write
TOC1 : Time-out Counter for Channel 1\nThis controls the period of time-out function for channel 1. The calculation unit is based on 10 kHz clock. The example of time-out period can refer TOC0 bit description.
bits : 16 - 31 (16 bit)
access : read-write
PDMA Channel Reset Register
address_offset : 0x460 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CHnRST : Channel n Reset\nNote: This function don't support stride mode.
bits : 0 - 15 (16 bit)
access : read-write
Enumeration:
0 : 0
corresponding channel n is not reset
1 : 1
corresponding channel n is reset
End of enumeration elements list.
PDMA Request Source Select Register 0
address_offset : 0x480 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
REQSRC0 : Channel 0 Request Source Selection\nThis filed defines which peripheral is connected to PDMA channel 0. User can configure the peripheral by setting REQSRC0.\nNote 1: A peripheral cannot be assigned to two channels at the same time.\nNote 2: This field is useless when transfer between memory and memory.
bits : 0 - 6 (7 bit)
access : read-write
Enumeration:
0 : 0
Disable PDMA peripheral request
1 : 1
Reserved.
2 : 2
Channel connects to USB_TX
3 : 3
Channel connects to USB_RX
4 : 4
Channel connects to UART0_TX
5 : 5
Channel connects to UART0_RX
6 : 6
Channel connects to UART1_TX
7 : 7
Channel connects to UART1_RX
8 : 8
Channel connects to UART2_TX
9 : 9
Channel connects to UART2_RX
10 : 10
Channel connects to UART3_TX
11 : 11
Channel connects to UART3_RX
12 : 12
Channel connects to UART4_TX
13 : 13
Channel connects to UART4_RX
14 : 14
Channel connects to UART5_TX
15 : 15
Channel connects to UART5_RX
16 : 16
Channel connects to USCI0_TX
17 : 17
Channel connects to USCI0_RX
18 : 18
Channel connects to USCI1_TX
19 : 19
Channel connects to USCI1_RX
20 : 20
Channel connects to QSPI0_TX
21 : 21
Channel connects to QSPI0_RX
22 : 22
Channel connects to SPI0_TX
23 : 23
Channel connects to SPI0_RX
24 : 24
Channel connects to SPI1_TX
25 : 25
Channel connects to SPI1_RX
26 : 26
Channel connects to SPI2_TX
27 : 27
Channel connects to SPI2_RX
28 : 28
Channel connects to SPI3_TX
29 : 29
Channel connects to SPI3_RX
30 : 30
Channel connects to QSPI1_TX
31 : 31
Channel connects to QSPI1_RX
32 : 32
Channel connects to EPWM0_P1_RX
33 : 33
Channel connects to EPWM0_P2_RX
34 : 34
Channel connects to EPWM0_P3_RX
35 : 35
Channel connects to EPWM1_P1_RX
36 : 36
Channel connects to EPWM1_P2_RX
37 : 37
Channel connects to EPWM1_P3_RX
38 : 38
Channel connects to I2C0_TX
39 : 39
Channel connects to I2C0_RX
40 : 40
Channel connects to I2C1_TX
41 : 41
Channel connects to I2C1_RX
42 : 42
Channel connects to I2C2_TX
43 : 43
Channel connects to I2C2_RX
44 : 44
Channel connects to I2S0_TX
45 : 45
Channel connects to I2S0_RX
46 : 46
Channel connects to TMR0
47 : 47
Channel connects to TMR1
48 : 48
Channel connects to TMR2
49 : 49
Channel connects to TMR3
50 : 50
Channel connects to EADC0_RX
51 : 51
Channel connects to DAC0_TX
52 : 52
Channel connects to DAC1_TX
53 : 53
Channel connects to EPWM0_CH0_TX
54 : 54
Channel connects to EPWM0_CH1_TX
55 : 55
Channel connects to EPWM0_CH2_TX
56 : 56
Channel connects to EPWM0_CH3_TX
57 : 57
Channel connects to EPWM0_CH4_TX
58 : 58
Channel connects to EPWM0_CH5_TX
59 : 59
Channel connects to EPWM1_CH0_TX
60 : 60
Channel connects to EPWM1_CH1_TX
61 : 61
Channel connects to EPWM1_CH2_TX
62 : 62
Channel connects to EPWM1_CH3_TX
63 : 63
Channel connects to EPWM1_CH4_TX
64 : 64
Channel connects to EPWM1_CH5_TX
65 : 65
Reserved.
66 : 66
Channel connects to UART6_TX
67 : 67
Channel connects to UART6_RX
68 : 68
Channel connects to UART7_TX
69 : 69
Channel connects to UART7_RX
70 : 70
Channel connects to EADC1_RX
End of enumeration elements list.
REQSRC1 : Channel 1 Request Source Selection\nThis filed defines which peripheral is connected to PDMA channel 1. User can configure the peripheral setting by REQSRC1. \nNote: The channel configuration is the same as REQSRC0 field. Please refer to the explanation of REQSRC0.
bits : 8 - 14 (7 bit)
access : read-write
REQSRC2 : Channel 2 Request Source Selection\nThis filed defines which peripheral is connected to PDMA channel 2. User can configure the peripheral setting by REQSRC2. \nNote: The channel configuration is the same as REQSRC0 field. Please refer to the explanation of REQSRC0.
bits : 16 - 22 (7 bit)
access : read-write
REQSRC3 : Channel 3 Request Source Selection\nThis filed defines which peripheral is connected to PDMA channel 3. User can configure the peripheral setting by REQSRC3. \nNote: The channel configuration is the same as REQSRC0 field. Please refer to the explanation of REQSRC0.
bits : 24 - 30 (7 bit)
access : read-write
PDMA Request Source Select Register 1
address_offset : 0x484 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
REQSRC4 : Channel 4 Request Source Selection\nThis filed defines which peripheral is connected to PDMA channel 4. User can configure the peripheral setting by REQSRC4. \nNote: The channel configuration is the same as REQSRC0 field. Please refer to the explanation of REQSRC0.
bits : 0 - 6 (7 bit)
access : read-write
REQSRC5 : Channel 5 Request Source Selection\nThis filed defines which peripheral is connected to PDMA channel 5. User can configure the peripheral setting by REQSRC5. \nNote: The channel configuration is the same as REQSRC0 field. Please refer to the explanation of REQSRC0.
bits : 8 - 14 (7 bit)
access : read-write
REQSRC6 : Channel 6 Request Source Selection\nThis filed defines which peripheral is connected to PDMA channel 6. User can configure the peripheral setting by REQSRC6. \nNote: The channel configuration is the same as REQSRC0 field. Please refer to the explanation of REQSRC0.
bits : 16 - 22 (7 bit)
access : read-write
REQSRC7 : Channel 7 Request Source Selection\nThis filed defines which peripheral is connected to PDMA channel 7. User can configure the peripheral setting by REQSRC7. \nNote: The channel configuration is the same as REQSRC0 field. Please refer to the explanation of REQSRC0.
bits : 24 - 30 (7 bit)
access : read-write
PDMA Request Source Select Register 2
address_offset : 0x488 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
REQSRC8 : Channel 8 Request Source Selection\nThis filed defines which peripheral is connected to PDMA channel 8. User can configure the peripheral setting by REQSRC8. \nNote: The channel configuration is the same as REQSRC0 field. Please refer to the explanation of REQSRC0.
bits : 0 - 6 (7 bit)
access : read-write
REQSRC9 : Channel 9 Request Source Selection\nThis filed defines which peripheral is connected to PDMA channel 9. User can configure the peripheral setting by REQSRC9. \nNote: The channel configuration is the same as REQSRC0 field. Please refer to the explanation of REQSRC0.
bits : 8 - 14 (7 bit)
access : read-write
REQSRC10 : Channel 10 Request Source Selection\nThis filed defines which peripheral is connected to PDMA channel 10. User can configure the peripheral setting by REQSRC10. \nNote: The channel configuration is the same as REQSRC0 field. Please refer to the explanation of REQSRC0.
bits : 16 - 22 (7 bit)
access : read-write
REQSRC11 : Channel 11 Request Source Selection\nThis filed defines which peripheral is connected to PDMA channel 11. User can configure the peripheral setting by REQSRC11. \nNote: The channel configuration is the same as REQSRC0 field. Please refer to the explanation of REQSRC0.
bits : 24 - 30 (7 bit)
access : read-write
PDMA Request Source Select Register 3
address_offset : 0x48C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
REQSRC12 : Channel 12 Request Source Selection\nThis filed defines which peripheral is connected to PDMA channel 12. User can configure the peripheral setting by REQSRC12. \nNote: The channel configuration is the same as REQSRC0 field. Please refer to the explanation of REQSRC0.
bits : 0 - 6 (7 bit)
access : read-write
REQSRC13 : Channel 13 Request Source Selection\nThis filed defines which peripheral is connected to PDMA channel 13. User can configure the peripheral setting by REQSRC13. \nNote: The channel configuration is the same as REQSRC0 field. Please refer to the explanation of REQSRC0.
bits : 8 - 14 (7 bit)
access : read-write
REQSRC14 : Channel 14 Request Source Selection\nThis filed defines which peripheral is connected to PDMA channel 14. User can configure the peripheral setting by REQSRC14. \nNote: The channel configuration is the same as REQSRC0 field. Please refer to the explanation of REQSRC0.
bits : 16 - 22 (7 bit)
access : read-write
REQSRC15 : Channel 15 Request Source Selection\nThis filed defines which peripheral is connected to PDMA channel 15. User can configure the peripheral setting by REQSRC15. \nNote: The channel configuration is the same as REQSRC0 field. Please refer to the explanation of REQSRC0.
bits : 24 - 30 (7 bit)
access : read-write
Stride Transfer Count Register of PDMA Channel 0
address_offset : 0x500 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
STC : PDMA Stride Transfer Count\nThe 16-bit register defines the stride transfer count of each row, the real transfer count is (STC + 1).
bits : 0 - 15 (16 bit)
access : read-write
Address Stride Offset Control Register of PDMA Channel 0
address_offset : 0x504 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SASOL : PDMA Source Address Stride Offset Length\nThe 16-bit register defines the source address stride transfer offset count of each row.
bits : 0 - 15 (16 bit)
access : read-write
DASOL : PDMA Destination Address Stride Offset Length\nThe 16-bit register defines the destination address stride transfer offset count of each row.
bits : 16 - 31 (16 bit)
access : read-write
Stride Transfer Count Register of PDMA Channel 1
address_offset : 0x508 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
Address Stride Offset Control Register of PDMA Channel 1
address_offset : 0x50C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
Stride Transfer Count Register of PDMA Channel 2
address_offset : 0x510 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
Address Stride Offset Control Register of PDMA Channel 2
address_offset : 0x514 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
Stride Transfer Count Register of PDMA Channel 3
address_offset : 0x518 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
Address Stride Offset Control Register of PDMA Channel 3
address_offset : 0x51C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
Stride Transfer Count Register of PDMA Channel 4
address_offset : 0x520 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
Address Stride Offset Control Register of PDMA Channel 4
address_offset : 0x524 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
Stride Transfer Count Register of PDMA Channel 5
address_offset : 0x528 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
Address Stride Offset Control Register of PDMA Channel 5
address_offset : 0x52C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
Address Interval Control Register of PDMA Channel 0
address_offset : 0x600 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SAICNT : PDMA Source Address Interval Count\nThe 16-bit register defines the source address interval count of each row.\nNote: This register should be set to 0 when repeat count(PDMA_RCNTn) set to 0.
bits : 0 - 15 (16 bit)
access : read-write
DAICNT : PDMA Destination Address Interval Count\nThe 16-bit register defines the destination address interval count of each row.\nNote: This register should be set to 0 when repeat count(PDMA_RCNTn) set to 0.
bits : 16 - 31 (16 bit)
access : read-write
Repeat Count Register of PDMA Channel 0
address_offset : 0x604 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RCNT : PDMA Repeat Count\nThe 16-bit register defines the repeat times of block transfer.\nNote: This register should be set to 0 when stride function disabled.
bits : 0 - 15 (16 bit)
access : read-write
Address Interval Control Register of PDMA Channel 1
address_offset : 0x608 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
Repeat Count Register of PDMA Channel 1
address_offset : 0x60C Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.