Embeetle, an IDE designed from scratch for embedded software developers.address_offset : 0x0 Bytes (0x0)
size : 0x10 byte (0x0)
mem_usage : registers
protection : not protected
Analog Comparator 0 Control Register
address_offset : 0x0 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ACMPEN : Analog Comparator 0 Enable Bit\nNote: Analog comparator output needs to wait 2 us stable time after this bit is set.
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Analog Comparator 0 Disabled
#1 : 1
Analog Comparator 1 Enabled
End of enumeration elements list.
ACMPIE : Analog Comparator 0 Interrupt Enable Bit\n
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Interrupt function Disabled
#1 : 1
Interrupt function Enabled
End of enumeration elements list.
HYSSEL : Analog Comparator 0 Hysteresis Select Bit\n
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Hysteresis function Disabled
#1 : 1
Hysteresis function Enabled
End of enumeration elements list.
NEGSEL : Analog Comparator 0 Negative Input Select Bit\n
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
The source of the negative comparator input is from CPN0 pin
#1 : 1
The source of the negative comparator input is from internal band-gap voltage or comparator reference voltage
End of enumeration elements list.
RTRGEN : Analog Comparator 0 Rising Edge Trigger Enable Bit\nNote: The bit is only effective while analog comparator 0 triggers PWM or Timer.
bits : 8 - 8 (1 bit)
access : read-write
Enumeration:
#0 : 0
Analog comparator 0 rising edge trigger PWM or Timer enabled
#1 : 1
Analog comparator 0 rising edge trigger disabled
End of enumeration elements list.
FTRGEN : Analog Comparator 0 Falling Edge Trigger Enable\nNote: The bit is only effective while analog comparator 0 triggers PWM or Timer.
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
Analog comparator 0 falling edge trigger PWM or Timer enabled
#1 : 1
Analog comparator 0 falling edge trigger disabled
End of enumeration elements list.
FILTSEL : Comparator Output Filter Count Selection\n
bits : 20 - 23 (4 bit)
access : read-write
Enumeration:
#0000 : 0
Filter function is Disabled
#0001 : 1
ACMP0 output is sampled 1 consecutive PCLK
#0010 : 2
ACMP0 output is sampled 2 consecutive PCLKs
#0011 : 3
ACMP0 output is sampled 4 consecutive PCLKs
#0100 : 4
ACMP0 output is sampled 8 consecutive PCLKs
#0101 : 5
ACMP0 output is sampled 16 consecutive PCLKs
#0110 : 6
ACMP0 output is sampled 32 consecutive PCLKs
#0111 : 7
ACMP0 output is sampled 64 consecutive PCLKs
#1000 : 8
ACMP0 output is sampled 128 consecutive PCLKs
#1001 : 9
ACMP0 output is sampled 256 consecutive PCLKs
#1010 : 10
ACMP0 output is sampled 512 consecutive PCLKs
End of enumeration elements list.
POSSEL : Analog Comparator 0 Positive Input Selection\n
bits : 29 - 30 (2 bit)
access : read-write
Enumeration:
#00 : 0
ACMP0_Px is from ACMP0_P0 (P1.5) pin
#01 : 1
ACMP0_Px is from ACMP0_P1 (P1.0) pin
#10 : 2
ACMP0_Px is from ACMP0_P2 (P1.2) pin
#11 : 3
ACMP0_Px is from ACMP0_P3 (P1.3) pin
End of enumeration elements list.
Analog Comparator 1 Control Register
address_offset : 0x4 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ACMPEN : Analog Comparator 1 Enable Bit\nNote: Analog comparator output needs to wait 2 us stable time after this bit is set.
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Analog Comparator 1 Disabled
#1 : 1
Analog Comparator 1 Enabled
End of enumeration elements list.
ACMPIE : Analog Comparator 1 Interrupt Enable Bit\n
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Interrupt function Disabled
#1 : 1
Interrupt function Enabled
End of enumeration elements list.
HYSSEL : Analog Comparator 1 Hysteresis Select Bit\n
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Hysteresis function Disabled
#1 : 1
Hysteresis function Enabled
End of enumeration elements list.
NEGSEL : Analog Comparator 1 Negative Input Select Bit\n
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
The source of the negative comparator input is from CPN1 pin
#1 : 1
The source of the negative comparator input is from internal band-gap voltage or comparator reference voltage
End of enumeration elements list.
RTRGEN : Analog Comparator 1 Rising Edge Trigger Enable Bit\nNote: The bit is only effective while analog comparator 1 triggers PWM or Timer.
bits : 8 - 8 (1 bit)
access : read-write
Enumeration:
#0 : 0
Analog comparator 1 rising edge trigger PWM or Timer Enabled
#1 : 1
Analog comparator 1 rising edge trigger Disabled
End of enumeration elements list.
FTRGEN : Analog Comparator 1 Falling Edge Trigger Enable Bit\nNote: The bit is only effective while analog comparator 1 triggers PWM or Timer.
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
Analog comparator 1 falling edge trigger PWM or Timer Enabled
#1 : 1
Analog comparator 1 falling edge trigger Disabled
End of enumeration elements list.
FILTSEL : Comparator Output Filter Count Selection\n
bits : 20 - 23 (4 bit)
access : read-write
Enumeration:
#0000 : 0
Filter function is Disabled
#0001 : 1
ACMP1 output is sampled 1 consecutive PCLK
#0010 : 2
ACMP1 output is sampled 2 consecutive PCLKs
#0011 : 3
ACMP1 output is sampled 4 consecutive PCLKs
#0100 : 4
ACMP1 output is sampled 8 consecutive PCLKs
#0101 : 5
ACMP1 output is sampled 16 consecutive PCLKs
#0110 : 6
ACMP1 output is sampled 32 consecutive PCLKs
#0111 : 7
ACMP1 output is sampled 64 consecutive PCLKs
#1000 : 8
ACMP1 output is sampled 128 consecutive PCLKs
#1001 : 9
ACMP1 output is sampled 256 consecutive PCLKs
#1010 : 10
ACMP1 output is sampled 512 consecutive PCLKs
End of enumeration elements list.
POSSEL : Analog Comparator 1 Positive Input Selection\n
bits : 29 - 30 (2 bit)
access : read-write
Enumeration:
#00 : 0
ACMP1_Px is from ACMP1_P0 (P3.1) pin
#01 : 1
ACMP1_Px is from ACMP1_P1 (P3.2) pin
#10 : 2
ACMP1_Px is from ACMP1_P2 (P3.4) pin
#11 : 3
ACMP1_Px is from ACMP1_P3 (P3.5) pin
End of enumeration elements list.
Analog Comparator 0/1 Status Register
address_offset : 0x8 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ACMPIF0 : Analog Comparator 0 Flag\nNote: This bit can be cleared to 0 by software writing 1.
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Analog comparator 0 output does not change
#1 : 1
Analog comparator 0 output changed
End of enumeration elements list.
ACMPIF1 : Analog Comparator 1 Flag\nNote: This bit can be cleared to 0 by software writing 1.
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
Analog comparator 1 output does not change
#1 : 1
Analog comparator 1 output changed
End of enumeration elements list.
ACMPO0 : Analog Comparator 0 Output\n
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Analog comparator 0 outputs 0
#1 : 1
Analog comparator 0 outputs 1
End of enumeration elements list.
ACMPO1 : Analog Comparator 1 Output\n
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Analog comparator 1 outputs 0
#1 : 1
Analog comparator 1 outputs 1
End of enumeration elements list.
Analog Comparator Reference Voltage Control Register
address_offset : 0xC Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CRVCTL : Comparator Reference Voltage Control\n
bits : 0 - 3 (4 bit)
access : read-write
IREFSEL : CRV Internal Reference Selection\n
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
#0 : 0
Band-gap voltage
#1 : 1
Internal comparator reference voltage
End of enumeration elements list.
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.