\n
address_offset : 0x0 Bytes (0x0)
size : 0x8 byte (0x0)
mem_usage : registers
protection : not protected
OP Amplifier Control Register
address_offset : 0x0 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OP0_EN : OP Amplifier 0 Enable\nThe OP Amplifier 0 output needs to wait stable 20 s after OP0_EN is first set.
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
OP Amplifier 0 Disabled
#1 : 1
OP Amplifier 0 Enabled
End of enumeration elements list.
OP1_EN : OP Amplifier 1 Enable\nThe OP Amplifier 1 output needs to wait stable 20 s after OP1_EN is first set.
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
OP Amplifier 1 Disabled
#1 : 1
OP Amplifier 1 Enabled
End of enumeration elements list.
OPSCH0_EN : OP Amplifier 0 Schmitt Trigger Non-inverting Buffer Enable
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OPSCH1_EN : OP Amplifier 1 Schmitt Trigger Non-inverting Buffer Enable
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
OPDIE0 : OP Amplifier 0 Schmitt Trigger Digital Output Interrupt Enable\nThe OPDF0 interrupt flag is set by hardware whenever the OP amplifier 0 Schmitt trigger non-inverting buffer digital output changes state, in the meanwhile, if OPDIE0 is set to 1, a comparator interrupt request is generated.
bits : 8 - 8 (1 bit)
access : read-write
Enumeration:
#0 : 0
OP Amplifier 0 digital output interrupt function Disabled
#1 : 1
OP Amplifier 0 digital output interrupt function Enabled
End of enumeration elements list.
OPDIE1 : OP Amplifier 1 Schmitt Trigger Digital Output Interrupt Enable\nThe OPDF1 interrupt flag is set by hardware whenever the OP amplifier 1 Schmitt trigger non-inverting buffer digital output changes state, in the meanwhile, if OPDIE1 is set to 1, a comparator interrupt request is generated.
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
OP Amplifier 1 digital output interrupt function Disabled
#1 : 1
OP Amplifier 1 digital output interrupt function Enabled
End of enumeration elements list.
OP Amplifier Status Register
address_offset : 0x4 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
OPDO0 : OP Amplifier 0 Digital Output
bits : 0 - 0 (1 bit)
access : read-write
OPDO1 : OP Amplifier 1 Digital Output
bits : 1 - 1 (1 bit)
access : read-write
OPDF0 : OP Amplifier 0 Schmitt Trigger Digital Output Interrupt Flag\nOPDF0 interrupt flag is set by hardware whenever the OP amplifier 0 Schmitt trigger non-inverting buffer digital output changes state. This bit is cleared by writing 1 to itself.
bits : 4 - 4 (1 bit)
access : read-write
OPDF1 : OP Amplifier 1 Schmitt Trigger Digital Output Interrupt Flag\nOPDF1 interrupt flag is set by hardware whenever the OP amplifier 1 Schmitt trigger non-inverting buffer digital output changes state. This bit is cleared by writing 1 to itself.
bits : 5 - 5 (1 bit)
access : read-write
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.