\n
address_offset : 0x0 Bytes (0x0)
size : 0x1C byte (0x0)
mem_usage : registers
protection : not protected
ISP Control Register
address_offset : 0x0 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ISPEN : ISP Enable (write-protected)\nISP function enable bit. Set this bit to enable ISP function.
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disable ISP function
#1 : 1
Enable ISP function
End of enumeration elements list.
BS : Boot Select (write-protected)
Set/clear this bit to select next booting from LDROM/APROM, respectively. This bit also functions as MCU booting status flag, which can be used to check where MCU booted from. This bit is initiated with the inversed value of CBS in Config0 after power-on reset It keeps the same value at other reset.
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
#0 : 0
boot from APROM
#1 : 1
boot from LDROM
End of enumeration elements list.
APUEN : APROM Update Enable (write-protected)
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
APROM can not be updated when the chip runs in APROM
#1 : 1
APROM can be updated when the chip runs in APROM
End of enumeration elements list.
CFGUEN : Config Update Enable (write-protected)
Writing this bit to 1 enables s/w to update Config value by ISP procedure regardless of program code is running in APROM or LDROM.
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
Config update disable
#1 : 1
Config update enable
End of enumeration elements list.
LDUEN : LDROM Update Enable (write-protection bit)\nLDROM update enable bit.
bits : 5 - 5 (1 bit)
access : read-write
Enumeration:
#0 : 0
LDROM cannot be updated
#1 : 1
LDROM can be updated
End of enumeration elements list.
ISPFF : ISP Fail Flag (write-protection bit)\nThis bit is set by hardware when a triggered ISP meets any of the following conditions:\n(1) APROM writes to itself if APUEN is set to 0\n(2) LDROM writes to itself if LDUEN is set to 0\n(3) CONFIG is erased/programmed if CFGUEN is set to 0\n(4) Destination address is illegal, such as over an available range\nWrite 1 to clear.
bits : 6 - 6 (1 bit)
access : read-write
ISP Trigger Control Register
address_offset : 0x10 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ISPGO : ISP start trigger(write-protected)\nWrite 1 to start ISP operation and this bit will be cleared to 0 by hardware automatically when ISP operation is finish.
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
ISP done
#1 : 1
ISP is on going
End of enumeration elements list.
Data Flash Base Address
address_offset : 0x14 Bytes (0x0)
size : -1 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
DFBADR : Data Flash Base Address\nThis register indicates data flash start address. It is a read only register.\nFor 8/16/32/64KB flash memory device, the data flash size is 4KB and it start address is fixed at 0x0001_F000 by hardware internally.
bits : 0 - 31 (32 bit)
access : read-only
Flash Access Time Control Register
address_offset : 0x18 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
LFOM : Low Frequency Optimization Mode (write-protected)\nWhen chip operation frequency is lower than 25 MHz, chip can work more efficiently by setting this bit to 1
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disable low frequency optimization mode
#1 : 1
Enable low frequency optimization mode
End of enumeration elements list.
ISP Address Register
address_offset : 0x4 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ISPADR : ISP Address \nNuMicro NUC029 series equips with a 16k x 32 embedded flash, it supports word program only. ISPADR[1:0] must be kept 2'b00 for ISP operation.
bits : 0 - 31 (32 bit)
access : read-write
ISP Data Register
address_offset : 0x8 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ISPDAT : ISP Data
Write data to this register before ISP program operation
Read data from this register after ISP read operation
bits : 0 - 31 (32 bit)
access : read-write
ISP Command Register
address_offset : 0xC Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ISPCMD : ISP Command
bits : 0 - 5 (6 bit)
access : read-write
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.