\n

CMP

Peripheral Memory Blocks

address_offset : 0x0 Bytes (0x0)
size : 0xC byte (0x0)
mem_usage : registers
protection : not protected

Registers

CMP0CR

CMP1CR

CMPSR


CMP0CR

Comparator0 Control Register
address_offset : 0x0 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

CMP0CR CMP0CR read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 CMP0EN CMP0IE CMP0_HYSEN CMP0CN

CMP0EN : Comparator0 Enable\nComparator output needs wait 2 us stable time after CMP0EN is set.
bits : 0 - 0 (1 bit)
access : read-write

Enumeration:

#0 : 0

Disabled

#1 : 1

Enabled

End of enumeration elements list.

CMP0IE : Comparator0 Interrupt Enable\n
bits : 1 - 1 (1 bit)
access : read-write

Enumeration:

#0 : 0

Interrupt function Disabled

#1 : 1

Interrupt function Enabled

End of enumeration elements list.

CMP0_HYSEN : Comparator0 Hysteresis Enable\n
bits : 2 - 2 (1 bit)
access : read-write

Enumeration:

#0 : 0

Hysteresis function Disabled (Default)

#1 : 1

Hysteresis function Enabled. The typical range is 20mV

End of enumeration elements list.

CMP0CN : Comparator0 Negative Input Selection\n
bits : 4 - 4 (1 bit)
access : read-write

Enumeration:

#0 : 0

The source of the negative comparator input is from CPN0 pin

#1 : 1

Internal band-gap reference voltage is selected as the source of negative comparator input

End of enumeration elements list.


CMP1CR

Comparator1 Control Register
address_offset : 0x4 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

CMP1CR CMP1CR read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 CMP1EN CMP1IE CMP1_HYSEN CMP1CN

CMP1EN : Comparator1 Enable\nComparator output needs to wait 2 us stable time after CMP1EN is set.
bits : 0 - 0 (1 bit)
access : read-write

Enumeration:

#0 : 0

Disabled

#1 : 1

Enabled

End of enumeration elements list.

CMP1IE : Comparator1 Interrupt Enable\n
bits : 1 - 1 (1 bit)
access : read-write

Enumeration:

#0 : 0

Interrupt function Disabled

#1 : 1

Interrupt function Enabled

End of enumeration elements list.

CMP1_HYSEN : Comparator1 Hysteresis Enable\n
bits : 2 - 2 (1 bit)
access : read-write

Enumeration:

#0 : 0

Hysteresis function Disabled (default)

#1 : 1

Hysteresis function Enabled. The typical range is 20mV

End of enumeration elements list.

CMP1CN : Comparator1 Negative Input Selection\n
bits : 4 - 4 (1 bit)
access : read-write

Enumeration:

#0 : 0

The source of the negative comparator input is from CPN1 pin

#1 : 1

Internal band-gap reference voltage is selected as the source of negative comparator input

End of enumeration elements list.


CMPSR

Comparator Status Register
address_offset : 0x8 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

CMPSR CMPSR read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 CMPF0 CMPF1 CO0 CO1

CMPF0 : Comparator0 Flag\nThis bit is set by hardware whenever the comparator0 output changes state. This will cause an interrupt if CMP0IE set.\nWrite 1 to clear this bit to 0.
bits : 0 - 0 (1 bit)
access : read-write

CMPF1 : Comparator1 Flag\nThis bit is set by hardware whenever the comparator1 output changes state. This will cause an interrupt if CMP1IE set.\nWrite 1 to clear this bit to 0.
bits : 1 - 1 (1 bit)
access : read-write

CO0 : Comparator0 Output\n
bits : 2 - 2 (1 bit)
access : read-write

CO1 : Comparator1 Output\n
bits : 3 - 3 (1 bit)
access : read-write



Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !

This website is sponsored by EmbeetleEmbeetle, an IDE designed from scratch for embedded software developers.