\n
address_offset : 0x0 Bytes (0x0)
size : 0x14 byte (0x0)
mem_usage : registers
protection : not protected
PDMA Global Control Register
address_offset : 0x0 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CLK0_EN : PDMA Controller Channel 0 Clock Enable Control\n
bits : 8 - 8 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
CLK1_EN : PDMA Controller Channel 1 Clock Enable Control (NuMicro( NUC100/NUC120 Medium Density Only)\n
bits : 9 - 9 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
CLK2_EN : PDMA Controller Channel 2 Clock Enable Control (NuMicro( NUC100/NUC120 Medium Density Only)\n
bits : 10 - 10 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
CLK3_EN : PDMA Controller Channel 3 Clock Enable Control (NuMicro( NUC100/NUC120 Medium Density Only)\n
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
CLK4_EN : PDMA Controller Channel 4 Clock Enable Control (NuMicro( NUC100/NUC120 Medium Density Only)\n
bits : 12 - 12 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
CLK5_EN : PDMA Controller Channel 5 Clock Enable Control (NuMicro( NUC100/NUC120 Medium Density Only)\n
bits : 13 - 13 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
CLK6_EN : PDMA Controller Channel 6 Clock Enable Control (NuMicro( NUC100/NUC120 Medium Density Only)\n
bits : 14 - 14 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
CLK7_EN : PDMA Controller Channel 7 Clock Enable Control (NuMicro( NUC100/NUC120 Medium Density Only)\n
bits : 15 - 15 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
CLK8_EN : PDMA Controller Channel 8 Clock Enable Control (NuMicro( NUC100/NUC120 Medium Density Only)\n
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
PDMA Service Selection Control Register 2
address_offset : 0x10 Bytes (0x0)
size : -1 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
I2S_RXSEL : PDMA I2S RX Selection
This filed defines which PDMA channel is connected to the on-chip peripheral I2S RX. Software can change the channel RX setting by I2S_RXSEL.
4'b0000: CH0
4'b0001: CH1
4'b0010: CH2
4'b0011: CH3
4'b0100: CH4
4'b0101: CH5
4'b0110: CH6
4'b0111: CH7
4'b1000: CH8
Others : Reserved
bits : 0 - 3 (4 bit)
access : read-write
I2S_TXSEL : PDMA I2S TX Selection\nThis filed defines which PDMA channel is connected to the on-chip peripheral I2S TX. Software can configure the TX channel setting by I2S_TXSEL. The channel configuration is the same as I2S_RXSEL field. Please refer to the explanation of I2S_RXSEL.
bits : 4 - 7 (4 bit)
access : read-write
PDMA Service Selection Control Register 0
address_offset : 0x4 Bytes (0x0)
size : -1 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SPI0_RXSEL : PDMA SPI0 RX Selection\nThis filed defines which PDMA channel is connected to the on-chip peripheral SPI0 RX. Software can change the channel RX setting by SPI0_RXSEL\n4'b0000: CH0\n4'b0001: CH1\n4'b0010: CH2\n4'b0011: CH3 \n4'b0100: CH4 \n4'b0101: CH5\n4'b0110: CH6\n4'b0111: CH7\n4'b1000: CH8\nOthers : Reserved\n(The NuMicro( NUC100/NUC120 Low Density should ne set as 4'b0000 for PDMA channel 0 only.)
bits : 0 - 3 (4 bit)
access : read-write
SPI0_TXSEL : PDMA SPI0 TX Selection\nThis filed defines which PDMA channel is connected to the on-chip peripheral SPI0 TX. Software can configure the TX channel setting by SPI0_TXSEL. The channel configuration is the same as SPI0_RXSEL field. Please refer to the explanation of SPI0_RXSEL.
bits : 4 - 7 (4 bit)
access : read-write
SPI1_RXSEL : PDMA SPI1 RX Selection\nThis filed defines which PDMA channel is connected to the on-chip peripheral SPI1 RX. Software can configure the RX channel setting by SPI1_RXSEL. The channel configuration is the same as SPI0_RXSEL field. Please refer to the explanation of SPI0_RXSEL.
bits : 8 - 11 (4 bit)
access : read-write
SPI1_TXSEL : PDMA SPI1 TX Selection\nThis filed defines which PDMA channel is connected to the on-chip peripheral SPI1 TX. Software can configure the TX channel setting by SPI1_TXSEL. The channel configuration is the same as SPI0_RXSEL field. Please refer to the explanation of SPI0_RXSEL.
bits : 12 - 15 (4 bit)
access : read-write
SPI2_RXSEL : PDMA SPI2 RX Selection (NuMicro( NUC100/NUC120 Medium Density Only)\nThis filed defines which PDMA channel is connected to the on-chip peripheral SPI2 RX. Software can configure the RX channel setting by SPI2_RXSEL. The channel configuration is the same as SPI0_RXSEL field. Please refer to the explanation of SPI0_RXSEL.
bits : 16 - 19 (4 bit)
access : read-write
SPI2_TXSEL : PDMA SPI2 TX Selection (NuMicro( NUC100/NUC120 Medium Density Only)\nThis filed defines which PDMA channel is connected to the on-chip peripheral SPI2 TX. Software can configure the TX channel setting by SPI2_TXSEL. The channel configuration is the same as SPI0_RXSEL field. Please refer to the explanation of SPI0_RXSEL.
bits : 20 - 23 (4 bit)
access : read-write
SPI3_RXSEL : PDMA SPI3 RX Selection (NuMicro( NUC100/NUC120 Medium Density Only)\nThis filed defines which PDMA channel is connected to the on-chip peripheral SPI3 RX. Software can configure the RX channel setting by SPI3_RXSEL. The channel configuration is the same as SPI0_RXSEL field. Please refer to the explanation of SPI0_RXSEL.
bits : 24 - 27 (4 bit)
access : read-write
SPI3_TXSEL : PDMA SPI3 TX Selection (NuMicro( NUC100/NUC120 Medium Density Only)\nThis filed defines which PDMA channel is connected to the on-chip peripheral SPI3 TX. Software can configure the TX channel setting by SPI3_TXSEL. The channel configuration is the same as SPI0_RXSEL field. Please refer to the explanation of SPI0_RXSEL.
bits : 28 - 31 (4 bit)
access : read-write
PDMA Service Selection Control Register 1
address_offset : 0x8 Bytes (0x0)
size : -1 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
UART0_RXSEL : This filed defines which PDMA channel is connected to the on-chip peripheral UART0 RX. Software can change the channel RX setting by UART0_RXSEL\n4'b0000: CH0\n4'b0001: CH1\n4'b0010: CH2\n4'b0011: CH3 \n4'b0100: CH4 \n4'b0101: CH5\n4'b0110: CH6\n4'b0111: CH7\n4'b1000: CH8\nOthers : Reserved\n(The NuMicro( NUC100/NUC120 Low Density should be set as 4'b0000 for PDMA channel 0 only.)
bits : 0 - 3 (4 bit)
access : read-write
UART0_TXSEL : PDMA UART0 TX Selection\nThis filed defines which PDMA channel is connected to the on-chip peripheral UART0 TX. Software can configure the TX channel setting by UART0_TXSEL. The channel configuration is the same as UART0_RXSEL field. Please refer to the explanation of UART0_RXSEL
bits : 4 - 7 (4 bit)
access : read-write
UART1_RXSEL : PDMA UART1 RX Selection\nThis filed defines which PDMA channel is connected to the on-chip peripheral UART1 RX. Software can configure the RX channel setting by UART1_RXSEL. The channel configuration is the same as UART0_RXSEL field. Please refer to the explanation of UART0_RXSEL
bits : 8 - 11 (4 bit)
access : read-write
UART1_TXSEL : PDMA UART1 TX Selection\nThis filed defines which PDMA channel is connected to the on-chip peripheral UART1 TX. Software can configure the TX channel setting by UART1_TXSEL. The channel configuration is the same as UART0_RXSEL field. Please refer to the explanation of UART0_RXSEL
bits : 12 - 15 (4 bit)
access : read-write
ADC_RXSEL : PDMA ADC RX Selection\nThis filed defines which PDMA channel is connected to the on-chip peripheral ADC RX. Software can configure the RX channel setting by ADC_RXSEL. The channel configuration is the same as UART0_RXSEL field. Please refer to the explanation of UART0_RXSEL
bits : 24 - 27 (4 bit)
access : read-write
PDMA Global Interrupt Register
address_offset : 0xC Bytes (0x0)
access : read-only
reset_value : 0x0
reset_Mask : 0x0
INTR0 : Interrupt Pin Status of Channel 0\nThis bit is the Interrupt status of PDMA channel0.\nNote: This bit is read only
bits : 0 - 0 (1 bit)
access : read-only
INTR1 : Interrupt Pin Status of Channel 1 (NuMicro( NUC100/NUC120 Medium Density Only)\nThis bit is the Interrupt status of PDMA channel1.\nNote: This bit is read only
bits : 1 - 1 (1 bit)
access : read-only
INTR2 : Interrupt Pin Status of Channel 2 (NuMicro( NUC100/NUC120 Medium Density Only)\nThis bit is the Interrupt status of PDMA channel2.\nNote: This bit is read only
bits : 2 - 2 (1 bit)
access : read-only
INTR3 : Interrupt Pin Status of Channel 3 (NuMicro( NUC100/NUC120 Medium Density Only)\nThis bit is the Interrupt status of PDMA channel3.\nNote: This bit is read only
bits : 3 - 3 (1 bit)
access : read-only
INTR4 : Interrupt Pin Status of Channel 4 (NuMicro( NUC100/NUC120 Medium Density Only)\nThis bit is the Interrupt status of PDMA channel4.\nNote: This bit is read only
bits : 4 - 4 (1 bit)
access : read-only
INTR5 : Interrupt Pin Status of Channel 5 (NuMicro( NUC100/NUC120 Medium Density Only)\nThis bit is the Interrupt status of PDMA channel5.\nNote: This bit is read only
bits : 5 - 5 (1 bit)
access : read-only
INTR6 : Interrupt Pin Status of Channel 6 (NuMicro( NUC100/NUC120 Medium Density Only)\nThis bit is the Interrupt status of PDMA channel6.\nNote: This bit is read only
bits : 6 - 6 (1 bit)
access : read-only
INTR7 : Interrupt Pin Status of Channel 7 (NuMicro( NUC100/NUC120 Medium Density Only)\nThis bit is the Interrupt status of PDMA channel7.\nNote: This bit is read only
bits : 7 - 7 (1 bit)
access : read-only
INTR8 : Interrupt Pin Status of Channel 8 (NuMicro( NUC100/NUC120 Medium Density Only)\nThis bit is the Interrupt status of PDMA channel8.\nNote: This bit is read only
bits : 8 - 8 (1 bit)
access : read-only
INTR : Interrupt Pin Status\nThis bit is the Interrupt status of PDMA controller.\nNote: This bit is read only
bits : 31 - 31 (1 bit)
access : read-only
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.