\n

PDMA

Peripheral Memory Blocks

address_offset : 0x0 Bytes (0x0)
size : 0x28 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x80 Bytes (0x0)
size : 0x4 byte (0x0)
mem_usage : registers
protection : not protected

Registers

PDMA_CSR

PDMA_POINT

PDMA_CSAR

PDMA_CDAR

PDMA_CBCR

PDMA_IER

PDMA_ISR

PDMA_SAR

PDMA_DAR

PDMA_SBUF0_c

PDMA_BCR


PDMA_CSR

PDMA Control Register
address_offset : 0x0 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PDMA_CSR PDMA_CSR read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 PDMACEN SW_RST MODE_SEL SAD_SEL DAD_SEL APB_TWS TRIG_EN

PDMACEN : PDMA Channel Enable\nSetting this bit to 1 enables PDMA's operation. If this bit is cleared, PDMA will ignore all PDMA request and force Bus Master into IDLE state.\n
bits : 0 - 0 (1 bit)
access : read-write

SW_RST : Software Engine Reset\n
bits : 1 - 1 (1 bit)
access : read-write

Enumeration:

#0 : 0

No effect

#1 : 1

Reset the internal state machine, pointers and internal buffer. The contents of control register will not be cleared. This bit will auto clear after few clock cycles

End of enumeration elements list.

MODE_SEL : PDMA Mode Selection\n
bits : 2 - 3 (2 bit)
access : read-write

Enumeration:

#00 : 0

Memory to Memory mode (Memory-to-Memory)

#01 : 1

Peripheral to Memory mode (Peripheral-to-Memory)

#10 : 2

Memory to Peripheral mode (Memory-to-Peripheral)

End of enumeration elements list.

SAD_SEL : Transfer Source Address Direction Selection\n
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

#00 : 0

Transfer Source address is increasing successively

#01 : 1

Reserved

#10 : 2

Transfer Source address is fixed (This feature can be used when data where transferred from a single source to multiple destinations)

#11 : 3

Reserved

End of enumeration elements list.

DAD_SEL : Transfer Destination Address Direction Selection\n
bits : 6 - 7 (2 bit)
access : read-write

Enumeration:

#00 : 0

Transfer Destination address is increasing successively

#01 : 1

Reserved

#10 : 2

Transfer Destination address is fixed (This feature can be used when data where transferred from multiple sources to a single destination)

#11 : 3

Reserved

End of enumeration elements list.

APB_TWS : Peripheral transfer Width Selection\nNote: This field is meaningful only when MODE_SEL is Peripheral to Memory mode (Peripheral-to-Memory) or Memory to Peripheral mode (Memory-to-Peripheral).
bits : 19 - 20 (2 bit)
access : read-write

Enumeration:

#00 : 0

One word (32-bit) is transferred for every PDMA operation

#01 : 1

One byte (8-bit) is transferred for every PDMA operation

#10 : 2

One half-word (16-bit) is transferred for every PDMA operation

#11 : 3

Reserved

End of enumeration elements list.

TRIG_EN : Trigger Enable\nNote: When PDMA transfer is completed, this bit will be cleared automatically.\nIf the bus error occurs, all PDMA transfer will be stopped. Software must reset all PDMA channel, and then trigger again.
bits : 23 - 23 (1 bit)
access : read-write

Enumeration:

#0 : 0

No effect

#1 : 1

PDMA data read or write transfer Enabled

End of enumeration elements list.


PDMA_POINT

PDMA Internal Buffer Pointer
address_offset : 0x10 Bytes (0x0)
access : read-only
reset_value : 0x0
reset_Mask : 0x0

PDMA_POINT PDMA_POINT read-only 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 PDMA_POINT

PDMA_POINT : PDMA Internal Buffer Pointer Register (Read Only)\nThis field indicates the internal buffer pointer.
bits : 0 - 1 (2 bit)
access : read-only


PDMA_CSAR

PDMA Current Source Address Register
address_offset : 0x14 Bytes (0x0)
access : read-only
reset_value : 0x0
reset_Mask : 0x0

PDMA_CSAR PDMA_CSAR read-only 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 PDMA_CSAR

PDMA_CSAR : PDMA Current Source Address Register (Read Only)\nThis field indicates the source address where the PDMA transfer just occurred.
bits : 0 - 31 (32 bit)
access : read-only


PDMA_CDAR

PDMA Current Destination Address Register
address_offset : 0x18 Bytes (0x0)
access : read-only
reset_value : 0x0
reset_Mask : 0x0

PDMA_CDAR PDMA_CDAR read-only 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 PDMA_CDAR

PDMA_CDAR : PDMA Current Destination Address Register (Read Only)\nThis field indicates the destination address where the PDMA transfer just occurred.
bits : 0 - 31 (32 bit)
access : read-only


PDMA_CBCR

PDMA Current Transfer Byte Count Register
address_offset : 0x1C Bytes (0x0)
access : read-only
reset_value : 0x0
reset_Mask : 0x0

PDMA_CBCR PDMA_CBCR read-only 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 PDMA_CBCR

PDMA_CBCR : PDMA Current Byte Count Register (Read Only)\nThis field indicates the current remained byte count of PDMA.\nNote: SW_RST will clear this register value.
bits : 0 - 15 (16 bit)
access : read-only


PDMA_IER

PDMA Interrupt Enable Register
address_offset : 0x20 Bytes (0x0)
size : -1 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PDMA_IER PDMA_IER read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 TABORT_IE BLKD_IE

TABORT_IE : PDMA Read/Write Target Abort Interrupt Enable\n
bits : 0 - 0 (1 bit)
access : read-write

Enumeration:

#0 : 0

Target abort interrupt generation Disabled during PDMA transfer

#1 : 1

Target abort interrupt generation Enabled during PDMA transfer

End of enumeration elements list.

BLKD_IE : PDMA Transfer Done Interrupt Enable\n
bits : 1 - 1 (1 bit)
access : read-write

Enumeration:

#0 : 0

Interrupt generator Disabled when PDMA transfer is done

#1 : 1

Interrupt generator Enabled when PDMA transfer is done

End of enumeration elements list.


PDMA_ISR

PDMA Interrupt Status Register
address_offset : 0x24 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PDMA_ISR PDMA_ISR read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 TABORT_IF BLKD_IF

TABORT_IF : PDMA Read/Write Target Abort Interrupt Flag\nWrite 1 to clear this bit to 0.
bits : 0 - 0 (1 bit)
access : read-write

Enumeration:

#0 : 0

No bus ERROR response received

#1 : 1

Bus ERROR response received

End of enumeration elements list.

BLKD_IF : Block Transfer Done Interrupt Flag\nThis bit indicates that PDMA has finished all transfer.\nWrite 1 to clear this bit to 0.
bits : 1 - 1 (1 bit)
access : read-write

Enumeration:

#0 : 0

Not finished

#1 : 1

Done

End of enumeration elements list.


PDMA_SAR

PDMA Source Address Register
address_offset : 0x4 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PDMA_SAR PDMA_SAR read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 PDMA_SAR

PDMA_SAR : PDMA Transfer Source Address Register\nThis field indicates a 32-bit source address of PDMA.\nNote: The source address must be word alignment
bits : 0 - 31 (32 bit)
access : read-write


PDMA_DAR

PDMA Destination Address Register
address_offset : 0x8 Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PDMA_DAR PDMA_DAR read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 PDMA_DAR

PDMA_DAR : PDMA Transfer Destination Address Register\nThis field indicates a 32-bit destination address of PDMA.\nNote: The destination address must be word alignment.
bits : 0 - 31 (32 bit)
access : read-write


PDMA_SBUF0_c

PDMA Shared Buffer FIFO 0
address_offset : 0x80 Bytes (0x0)
access : read-only
reset_value : 0x0
reset_Mask : 0x0

PDMA_SBUF0_c PDMA_SBUF0_c read-only 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 PDMA_SBUF0

PDMA_SBUF0 : PDMA Shared Buffer FIFO 0 (Read Only)\nEach channel has its own 1 words internal buffer.
bits : 0 - 31 (32 bit)
access : read-only


PDMA_BCR

PDMA Transfer Byte Count Register
address_offset : 0xC Bytes (0x0)
access : read-write
reset_value : 0x0
reset_Mask : 0x0

PDMA_BCR PDMA_BCR read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 PDMA_BCR

PDMA_BCR : PDMA Transfer Byte Count Register\nThis field indicates a 16-bit transfer byte count number of PDMA, which must be word alignment.
bits : 0 - 15 (16 bit)
access : read-write



Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !

This website is sponsored by EmbeetleEmbeetle, an IDE designed from scratch for embedded software developers.