PPR

CMR0

PDR0

CNR1

CMR1

PDR1

CNR2

CMR2

PDR2

CNR3

CMR3

PDR3

PBCR

CSR

PIER

PIIR

CCR0

CCR2

CRLR0

CFLR0

CRLR1

CFLR1

CRLR2

CFLR2

CRLR3

CFLR3

CAPENR

POE

PCR

TCON

TSTATUS

SYNCBUSY0

SYNCBUSY1

SYNCBUSY2

SYNCBUSY3

CNR0

CAPPDMACTL

CAP0PDMA

CAP1PDMA

CAP2PDMA

CAP3PDMA

CP01 : Clock Prescaler 0 (PWM-timer 0 / 1) Clock input is divided by (CP01 + 1) before it is fed to the corresponding PWM-timer.
bits : 0 - 7 (8 bit)
access : read-write

CP23 : Clock Prescaler 2 (PWM Timer2 / 3)\nClock input is divided by (CP23 + 1) before it is fed to the corresponding PWM-timer.\n
bits : 8 - 15 (8 bit)
access : read-write

DZI01 : Dead-zone Interval for Pair of Channel 0 and Channel 1 (PWM0 and PWM1 Pair)\nThese 8 bits determine dead-zone length.\nThe unit time of dead-zone length is received from corresponding CSR bits.
bits : 16 - 23 (8 bit)
access : read-write

DZI23 : Dead-zone Interval for Pair of Channel2 and Channel3 (PWM2 and PWM3 Pair)\nThese 8 bits determine dead-zone length.\nThe unit time of dead-zone length is received from corresponding CSR bits.
bits : 24 - 31 (8 bit)
access : read-write

CMRx : PWM Comparator Register\nCMR determines the PWM duty.\nNote: Any write to CNR will take effect in the next PWM cycle.
bits : 0 - 15 (16 bit)
access : read-write

PDRx : PWM Data Register\nUser can monitor PDR to know the current value in 16-bit down counter.
bits : 0 - 15 (16 bit)
access : read-only

CSR0 : PWM Timer 0 Clock Source Selection (PWM Timer 0)\nSelect clock input for PWM timer.\n(Table is the same as CSR3.)
bits : 0 - 2 (3 bit)
access : read-write

CSR1 : PWM Timer 1 Clock Source Selection (PWM Timer 1)\nSelect clock input for PWM timer.\n(Table is the same as CSR3.)
bits : 4 - 6 (3 bit)
access : read-write

CSR2 : PWM Timer 2 Clock Source Selection (PWM Timer 2)\nSelect clock input for PWM timer.\n(Table is the same as CSR3.)
bits : 8 - 10 (3 bit)
access : read-write

CSR3 : PWM Timer 3 Clock Source Selection (PWM timer 3)\n
bits : 12 - 14 (3 bit)
access : read-write

PWMIE0 : PWM Channel 0 Interrupt Enable\n
bits : 0 - 0 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

PWMIE1 : PWM Channel 1 Interrupt Enable\n
bits : 1 - 1 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

PWMIE2 : PWM Channel 2 Interrupt Enable\n
bits : 2 - 2 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

PWMIE3 : PWM Channel 3 Interrupt Enable\n
bits : 3 - 3 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

PWMDIE0 : PWM Channel 0 Duty Interrupt Enable\n
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

PWMDIE1 : PWM Channel 1 Duty Interrupt Enable\n
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

PWMDIE2 : PWM Channel 2 Duty Interrupt Enable\n
bits : 10 - 10 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

PWMDIE3 : PWM Channel 3 Duty Interrupt Enable\n
bits : 11 - 11 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

INTTYPE01 : PWM01 Interrupt Type Selection Bit (PWM0 and PWM1 Pair)\nNote: This bit is effective when PWM in central align mode only.
bits : 16 - 16 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

INTTYPE23 : PWM12 Interrupt Type Selection Bit (PWM2 and PWM3 Pair)\nNote: This bit is effective when PWM in central align mode only.
bits : 17 - 17 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

PWMIF0 : PWM channel 0 Interrupt Status\nThis bit is set by hardware when PWM0 counter reaches the requirement of interrupt (depending on INTTYPE01 bit of PIER register) if PWM0 interrupt enable bit (PWMIE0) is 1, software can write 1 to clear this bit to zero
bits : 0 - 0 (1 bit)
access : read-write

PWMIF1 : PWM channel 1 Interrupt Status\nThis bit is set by hardware when PWM1 counter reaches the requirement of interrupt (depending on INTTYPE01 bit of PIER register) if PWM1 interrupt enable bit (PWMIE1) is 1, software can write 1 to clear this bit to zero
bits : 1 - 1 (1 bit)
access : read-write

PWMIF2 : PWM channel 2 Interrupt Status\nThis bit is set by hardware when PWM2 counter reaches the requirement of interrupt (depending on INTTYPE23 bit of PIER register) if PWM2 interrupt enable bit (PWMIE2) is 1, software can write 1 to clear this bit to zero
bits : 2 - 2 (1 bit)
access : read-write

PWMIF3 : PWM channel 3 Interrupt Status\nThis bit is set by hardware when PWM3 counter reaches the requirement of interrupt (depending on INTTYPE23 bit of PIER register) if PWM3 interrupt enable bit (PWMIE3) is 1, software can write 1 to clear this bit to zero
bits : 3 - 3 (1 bit)
access : read-write

PWMDIF0 : PWM channel 0 Duty Interrupt Flag\nFlag is set by hardware when channel 0 PWM counter down count and reaches CMR0, software can clear this bit by writing a one to it.\nNote: If CMR is equal to CNR, this flag is not working
bits : 8 - 8 (1 bit)
access : read-write

PWMDIF1 : PWM channel 1 Duty Interrupt Flag\nFlag is set by hardware when channel 1 PWM counter down count and reaches CMR1, software can clear this bit by writing a one to it.\nNote: If CMR is equal to CNR, this flag is not working
bits : 9 - 9 (1 bit)
access : read-write

PWMDIF2 : PWM channel 2 Duty Interrupt Flag\nFlag is set by hardware when channel 2 PWM counter down count and reaches CMR2, software can clear this bit by writing a one to it.\nNote: If CMR is equal to CNR, this flag is not working
bits : 10 - 10 (1 bit)
access : read-write

PWMDIF3 : PWM channel 3 Duty Interrupt Flag\nFlag is set by hardware when channel 3 PWM counter down count and reaches CMR3, software can clear this bit by writing a one to it.\nNote: If CMR is equal to CNR, this flag is not working
bits : 11 - 11 (1 bit)
access : read-write

INV0 : Channel 0 Inverter Enable\n
bits : 0 - 0 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CRL_IE0 : Channel 0 Rising Latch Interrupt Enable\nWhen Enabled, if capture detects PWM group channel 0 has rising transition, capture issues an Interrupt.
bits : 1 - 1 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CFL_IE0 : Channel 0 Falling Latch Interrupt Enable\nWhen Enabled, if capture detects PWM group channel 0 has falling transition, capture issues an Interrupt.
bits : 2 - 2 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CAPCH0EN : Channel 0 Capture Function Enable\nWhen Enabled, Capture latched the PWM-counter value and saved to CRLR (Rising latch) and CFLR (Falling latch).\nWhen Disabled, capture does not update CRLR and CFLR, and disable PWM group channel 0 Interrupt.
bits : 3 - 3 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CAPIF0 : Channel 0 Capture Interrupt Indication Flag\nWrite 1 to clear this bit to zero
bits : 4 - 4 (1 bit)
access : read-write

CRLRI0 : CRLR0 Latched Indicator Bit\nWhen PWM group input channel 0 has a rising transition, CRLR0 was latched with the value of PWM down-counter and this bit is set by hardware.\nSoftware can write 0 to clear this bit to zero if BCn bit is 0, and can write 1 to clear this bit to zero if BCn bit is 1.
bits : 6 - 6 (1 bit)
access : read-write

CFLRI0 : CFLR0 Latched Indicator Bit\nWhen PWM group input channel 0 has a falling transition, CFLR0 was latched with the value of PWM down-counter and this bit is set by hardware.\nSoftware can write 0 to clear this bit to zero if BCn bit is 0, and can write 1 to clear this bit to zero if BCn bit is 1.
bits : 7 - 7 (1 bit)
access : read-write

INV1 : Channel 1 Inverter Enable\n
bits : 16 - 16 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CRL_IE1 : Channel 1 Rising Latch Interrupt Enable\nWhen Enable, if Capture detects PWM group channel 1 has rising transition, capture issues an Interrupt.
bits : 17 - 17 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CFL_IE1 : Channel 1 Falling Latch Interrupt Enable\nWhen Enabled, if Capture detects PWM group channel 1 has falling transition, capture issues an Interrupt.
bits : 18 - 18 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CAPCH1EN : Channel 1 Capture Function Enable\nWhen Enabled, Capture latched the PWM-counter and saved to CRLR (Rising latch) and CFLR (Falling latch).\nWhen Disabled, Capture does not update CRLR and CFLR, and disable PWM group channel 1 Interrupt.
bits : 19 - 19 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CAPIF1 : Channel 1 Capture Interrupt Indication Flag\nWrite 1 to clear this bit to zero
bits : 20 - 20 (1 bit)
access : read-write

CRLRI1 : CRLR1 Latched Indicator Bit\nWhen PWM group input channel 1 has a rising transition, CRLR1 is latched with the value of PWM down-counter and this bit is set by hardware.\nSoftware can write 0 to clear this bit to zero if BCn bit is 0, and can write 1 to clear this bit to zero if BCn bit is 1.
bits : 22 - 22 (1 bit)
access : read-write

CFLRI1 : CFLR1 Latched Indicator Bit\nWhen PWM group input channel 1 has a falling transition, CFLR1 is latched with the value of PWM down-counter and this bit is set by hardware.\nSoftware can write 0 to clear this bit to zero if BCn bit is 0, and can write 1 to clear this bit to zero if BCn bit is 1.
bits : 23 - 23 (1 bit)
access : read-write

INV2 : Channel 2 Inverter Enable\n
bits : 0 - 0 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CRL_IE2 : Channel 2 Rising Latch Interrupt Enable\nWhen Enabled, if Capture detects PWM group channel 2 has rising transition, Capture issues an Interrupt.
bits : 1 - 1 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CFL_IE2 : Channel 2 Falling Latch Interrupt Enable\nWhen Enabled, if capture detects PWM group channel 2 has falling transition, capture issues an Interrupt.
bits : 2 - 2 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CAPCH2EN : Channel 2 Capture Function Enable\nWhen Enabled, capture latched the PWM-counter value and saved to CRLR (Rising latch) and CFLR (Falling latch).\nWhen Disabled, capture does not update CRLR and CFLR, and disable PWM group channel 2 Interrupt.
bits : 3 - 3 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CAPIF2 : Channel 2 Capture Interrupt Indication Flag\nWrite 1 to clear this bit to zero
bits : 4 - 4 (1 bit)
access : read-write

CRLRI2 : CRLR2 Latched Indicator Bit\nWhen PWM group input channel 2 has a rising transition, CRLR2 was latched with the value of PWM down-counter and this bit is set by hardware.\nSoftware can write 0 to clear this bit to zero if BCn bit is 0, and can write 1 to clear this bit to zero if BCn bit is 1.
bits : 6 - 6 (1 bit)
access : read-write

CFLRI2 : CFLR2 Latched Indicator Bit\nWhen PWM group input channel 2 has a falling transition, CFLR2 was latched with the value of PWM down-counter and this bit is set by hardware.\nSoftware can write 0 to clear this bit to zero if BCn bit is 0, and can write 1 to clear this bit to zero if BCn bit is 1.
bits : 7 - 7 (1 bit)
access : read-write

INV3 : Channel 3 Inverter Enable\n
bits : 16 - 16 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CRL_IE3 : Channel 3 Rising Latch Interrupt Enable\nWhen Enabled, if Capture detects PWM group channel 3 has rising transition, capture issues an Interrupt.
bits : 17 - 17 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CFL_IE3 : Channel 3 Falling Latch Interrupt Enable\nWhen Enabled, if capture detects PWM group channel 3 has falling transition, capture issues an Interrupt.
bits : 18 - 18 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CAPCH3EN : Channel 3 Capture Function Enable\nWhen Enabled, capture latched the PWM-counter and saved to CRLR (Rising latch) and CFLR (Falling latch).\nWhen Disabled, capture does not update CRLR and CFLR, and disable PWM group channel 3 Interrupt.
bits : 19 - 19 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CAPIF3 : Channel 3 Capture Interrupt Indication Flag\nWrite 1 to clear this bit to zero
bits : 20 - 20 (1 bit)
access : read-write

CRLRI3 : CRLR3 Latched Indicator Bit\nWhen PWM group input channel 3 has a rising transition, CRLR3 was latched with the value of PWM down-counter and this bit is set by hardware.\nSoftware can write 0 to clear this bit to zero if BCn bit is 0, and can write 1 to clear this bit to zero if BCn bit is 1.
bits : 22 - 22 (1 bit)
access : read-write

CFLRI3 : CFLR3 Latched Indicator Bit\nWhen PWM group input channel 3 has a falling transition, CFLR3 was latched with the value of PWM down-counter and this bit is set by hardware.\nSoftware can write 0 to clear this bit to zero if BCn bit is 0, and can write 1 to clear this bit to zero if BCn bit is 1.
bits : 23 - 23 (1 bit)
access : read-write

CRLRx : Capture Rising Latch Register\nLatch the PWM counter when Channel 0/1/2/3 has rising transition.
bits : 0 - 15 (16 bit)
access : read-only

CFLRx : Capture Falling Latch Register\nLatch the PWM counter when Channel 01/2/3 has Falling transition.
bits : 0 - 15 (16 bit)
access : read-only

CAPENR : Capture Input Enable Register There are four capture inputs from pad. Bit0~Bit3 are used to control each input enable or disable. CAPENR Bit 3210 for PWM group A Bit xxx1 ( Capture channel 0 is from pin PA.12 Bit xx1x ( Capture channel 1 is from pin PA.13 Bit x1xx ( Capture channel 2 is from pin PA.14 Bit 1xxx ( Capture channel 3 is from pin PA.15 Bit 3210 for PWM group B Bit xxx1 ( Capture channel 0 is from pin PB.11 Bit xx1x ( Capture channel 1 is from pin PE.5 Bit x1xx ( Capture channel 2 is from pin PE.0 Bit 1xxx ( Capture channel 3 is from pin PE.1
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

End of enumeration elements list.

PWM0 : Channel 0 Output Enable Register\nNote: The corresponding GPIO pin must also be switched to PWM function.
bits : 0 - 0 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

PWM1 : Channel 1 Output Enable Register\nNote: The corresponding GPIO pin must also be switched to PWM function.
bits : 1 - 1 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

PWM2 : Channel 2 Output Enable Register\nNote: The corresponding GPIO pin must also be switched to PWM function.
bits : 2 - 2 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

PWM3 : Channel 3 Output Enable Register\nNote: The corresponding GPIO pin must also be switched to PWM function.
bits : 3 - 3 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CH0EN : PWM-Timer 0 Enable (PWM timer 0)\n
bits : 0 - 0 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CH0PINV : PWM-Timer 0 Output Polar Inverse Enable (PWM Timer 0)\n
bits : 1 - 1 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CH0INV : PWM-Timer 0 Output Inverter Enable (PWM Timer 0)\n
bits : 2 - 2 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CH0MOD : PWM-Timer 0 Auto-reload/One-Shot Mode (PWM Timer 0)\nNote: If there is a transition at this bit, it will cause CNR0 and CMR0 be clear.
bits : 3 - 3 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

DZEN01 : Dead-Zone 0 Generator Enable (PWM0 and PWM1 Pair)\nNote: When dead-zone generator is enabled, the pair of PWM0 and PWM1 becomes a complementary pair for PWM group A.
bits : 4 - 4 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

DZEN23 : Dead-Zone 2 Generator Enable (PWM2 and PWM3 Pair)\nNote: When dead-zone generator is enabled, the pair of PWM2 and PWM3 becomes a complementary pair for PWM group A and the pair of PWM6 and PWM7 becomes a complementary pair for PWM group B.
bits : 5 - 5 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CH1EN : PWM-Timer 1 Enable (PWM Timer 1)\n
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CH1PINV : PWM-Timer 1 Output Polar Inverse Enable (PWM Timer 1)\n
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CH1INV : PWM-Timer 1 Output Inverter Enable (PWM Timer 1)\n
bits : 10 - 10 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CH1MOD : PWM-Timer 1 Auto-reload/One-Shot Mode (PWM Timer 1)\nNote: If there is a transition at this bit, it will cause CNR1 and CMR1 be clear.
bits : 11 - 11 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CH2EN : PWM-Timer 2 Enable (PWM Timer 2)\n
bits : 16 - 16 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CH2PINV : PWM-Timer 2 Output Polar Inverse Enable (PWM Timer 2)\n
bits : 17 - 17 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CH2INV : PWM-Timer 2 Output Inverter Enable (PWM Timer 2)\n
bits : 18 - 18 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CH2MOD : PWM-Timer 2 Auto-reload/One-Shot Mode (PWM Timer 2)\nNote: If there is a transition at this bit, it will cause CNR2 and CMR2 be clear.
bits : 19 - 19 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CH3EN : PWM-Timer 3 Enable (PWM Timer 3)\n
bits : 24 - 24 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CH3PINV : PWM-Timer 3 Output Polar Inverse Enable (PWM Timer 3)\n
bits : 25 - 25 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CH3INV : PWM-Timer 3 Output Inverter Enable (PWM Timer 3)\n
bits : 26 - 26 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CH3MOD : PWM-Timer 3 Auto-reload/One-Shot Mode (PWM Timer 3)\nNote: If there is a transition at this bit, it will cause CNR3 and CMR3 be clear.
bits : 27 - 27 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

PWMTYPE01 : PWM01 Aligned Type Selection Bit (PWM0 and PWM1 Pair)\n
bits : 30 - 30 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

PWMTYPE23 : PWM23 Aligned Type Selection Bit (PWM2 and PWM3 Pair)\n
bits : 31 - 31 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

PWM0TEN : Channel 0 Center-Aligned Trigger Enable Register\nPWM can trigger ADC to start conversion when PWM counter counts up to CNR if this bit is set to 1.\nNote: This function is only supported when PWM operating in Center-aligned mode.
bits : 0 - 0 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

PWM1TEN : Channel 1 Center-Aligned Trigger Enable Register\nPWM can trigger ADC to start conversion when PWM counter counts up to CNR if this bit is set to 1.\nNote: This function is only supported when PWM operating in Center-aligned mode
bits : 1 - 1 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

PWM2TEN : Channel 2 Center-Aligned Trigger Enable Register\nPWM can trigger ADC to start conversion when PWM counter counts up to CNR if this bit is set to 1.\nNote: This function is only supported when PWM operating in Center-aligned mode.
bits : 2 - 2 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

PWM3TEN : Channel 3 Center-Aligned Trigger Enable Register\nPWM can trigger ADC to start conversion when PWM counter counts up to CNR if this bit is set to 1.\nNote: This function is only supported when PWM operating in Center-aligned mode.
bits : 3 - 3 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

PWM0TF : Channel 0 Center-aligned Trigger Flag\nFor Center-aligned operating mode, this bit is set to 1 by hardware when PWM counter up count to CNR if PWM0TEN bit is set to 1. After this bit is set to 1, ADC will start conversion if ADC triggered source is selected by PWM.\nSoftware can write 1 to clear this bit.
bits : 0 - 0 (1 bit)
access : read-write

PWM1TF : Channel 1 Center-aligned Trigger Flag\nFor Center-aligned operating mode, this bit is set to 1 by hardware when PWM counter up count to CNR if PWM1TEN bit is set to 1. After this bit is set to 1, ADC will start conversion if ADC triggered source is selected by PWM.\nSoftware can write 1 to clear this bit.
bits : 1 - 1 (1 bit)
access : read-write

PWM2TF : Channel 2 Center-aligned Trigger Flag\nFor Center-aligned operating mode, this bit is set to 1 by hardware when PWM counter up count to CNR if PWM2TEN bit is set to 1. After this bit is set to 1, ADC will start conversion if ADC triggered source is selected by PWM.\nSoftware can write 1 to clear this bit.
bits : 2 - 2 (1 bit)
access : read-write

PWM3TF : Channel 3 Center-aligned Trigger Flag\nFor Center-aligned operating mode, this bit is set to 1 by hardware when PWM counter up count to CNR if PWM3TEN bit is set to 1. After this bit is set to 1, ADC will start conversion if ADC triggered source is selected by PWM.\nSoftware can write 1 to clear this bit.
bits : 3 - 3 (1 bit)
access : read-write

S_BUSY : PWM Synchronous Busy\nWhen software writes CNR0/CMR0/PPR or switch PWM0 operation mode (PCR[3]), PWM will have a busy time to update these values completely because PWM clock may be different from system clock domain. Software needs to check this busy status before writes CNR0/CMR0/PPR or switch PWM0 operation mode (PCR[3]) to make sure previous setting has been update completely.\nThis bit will be set when software write CNR0/CMR0/PPR or switch PWM0 operation mode (PCR[3]) and will be cleared by hardware automatically when PWM update these value completely.
bits : 0 - 0 (1 bit)
access : read-only

S_BUSY : PWM Synchronous Busy\nWhen software writes CNR1/CMR1/PPR or switches PWM1 operation mode (PCR[11]), PWM will have a busy time to update these values completely because PWM clock may be different from system clock domain. Software needs to check this busy status before writing CNR1/CMR1/PPR or switching PWM1 operation mode (PCR[11]) to make sure the previous setting has been updated completely.\nThis bit will be set when software write CNR1/CMR1/PPR or switch PWM1 operation mode (PCR[11]) and will be cleared by hardware automatically when PWM updates these value completely.
bits : 0 - 0 (1 bit)
access : read-only

S_BUSY : PWM Synchronous Busy\nWhen software writes CNR2/CMR2/PPR or switch PWM2 operation mode (PCR[19]), PWM will have a busy time to update these values completely because PWM clock may be different from system clock domain. Software needs to check this busy status before writing CNR2/CMR2/PPR or switching PWM2 operation mode (PCR[19]) to make sure the previous setting has been updated completely.\nThis bit will be set when software write CNR2/CMR2/PPR or switch PWM2 operation mode (PCR[19]) and will be cleared by hardware automatically when PWM updates these value completely.
bits : 0 - 0 (1 bit)
access : read-only

S_BUSY : PWM Synchronous Busy\nWhen software writes CNR3/CMR3/PPR or switch PWM3 operation mode (PCR[27]), PWM will have a busy time to update these values completely because PWM clock may be different from system clock domain. Software needs to check this busy status before writing CNR3/CMR3/PPR or switching PWM3 operation mode (PCR[27]) to make sure the previous setting has been updated completely.\nThis bit will be set when software write CNR3/CMR3/PPR or switch PWM3 operation mode (PCR[27]) and will be cleared by hardware automatically when PWM updates these value completely.
bits : 0 - 0 (1 bit)
access : read-only

CNRx : PWM Timer Loaded Value\nCNR determines the PWM period.\nNote: Any write to CNR will take effect in the next PWM cycle.\nNote: When PWM operating at center-aligned type, CNR value should be set between 0x0000 to 0xFFFE. If CNR equal to 0xFFFF, the PWM will work unpredictable.\nNote: When CNR value is set to 0, PWM output is always high.
bits : 0 - 15 (16 bit)
access : read-write

CAP0PDMAEN : Channel 0 PDMA Enable\n
bits : 0 - 0 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CAP0PDMAMOD : Select CRLR0 or CFLR0 to Transfer PDMA\n
bits : 1 - 2 (2 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CAP0RFORDER : None
bits : 3 - 3 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CAP1PDMAEN : Channel 1 PDMA Enable\n
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CAP1PDMAMOD : Select CRLR1 or CFLR1 to Transfer PDMA\n
bits : 9 - 10 (2 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CAP1RFORDER : Capture channel 1 Rising/Falling Order\n
bits : 11 - 11 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CAP2PDMAEN : Channel 2 PDMA Enable\n
bits : 16 - 16 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CAP2PDMAMOD : Select CRLR2 or CFLR2 to do PDMA Transfer\n
bits : 17 - 18 (2 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CAP2RFORDER : Capture channel 2 Rising/Falling Order\n
bits : 19 - 19 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CAP3PDMAEN : Channel 3 PDMA enable\n
bits : 24 - 24 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CAP3PDMAMOD : Select CRLR3 or CFLR3 to do PDMA Transfer\n
bits : 25 - 26 (2 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CAP3RFORDER : Capture Channel 3 Rising/Falling Order\n
bits : 27 - 27 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CAP0RFPDMA : PDMA data register for channel 0\nit is the capturing value(CFLR0/CRLR0) for channel 0
bits : 0 - 15 (16 bit)
access : read-only

CAP1RFPDMA : PDMA data register for channel 1\nit is the capturing value(CFLR1/CRLR1) for channel 1
bits : 0 - 15 (16 bit)
access : read-only

CAP2RFPDMA : PDMA data register for channel 2\nit is the capturing value(CFLR2/CRLR2) for channel 2
bits : 0 - 15 (16 bit)
access : read-only

CAP3RFPDMA : PDMA data register for channel 3\nit is the capturing value(CFLR3/CRLR3) for channel 3
bits : 0 - 15 (16 bit)
access : read-only