SC_RBR

SC_THR

SC_RFTMR

SC_ETUCR

SC_IER

SC_ISR

SC_TRSR

SC_PINCSR

SC_TMR0

SC_TMR1

SC_TMR2

SC_UACTL

SC_TDRA

SC_TDRB

SC_CTL

SC_ALTCTL

SC_EGTR

RBR : Receiving Buffer \nBy reading RBR, the SC will return an 8-bit received data.
bits : 0 - 7 (8 bit)
access : read-only

THR : Transmit Holding Buffer\nBy writing data to THR, the SC will send out an 8-bit data.\nNote: If SC_CEN(SC_CTL[0]) is not enabled, THR cannot be programmed.
bits : 0 - 7 (8 bit)
access : write-only

RFTM : SC Receiver Buffer Time-Out (ETU Base)\nNote1: The counter unit is ETU based and the interval of time-out is RFTM + 0.5\nNote2: Fill all 0 to this field indicates to disable this function.
bits : 0 - 8 (9 bit)
access : read-write

ETU_RDIV : ETU Rate Divider\nThe field indicates the clock rate divider.\nThe real ETU is ETU_RDIV + 1.\nNote: Software can configure this field, but this field must be greater than 0x004.
bits : 0 - 11 (12 bit)
access : read-write

COMPEN_EN : Compensation Mode Enable Bit\nThis bit enables clock compensation function. When this bit enabled, hardware will alternate between n clock cycles and n-1 clock cycles, where n is the value to be written into the ETU_RDIV .\n
bits : 15 - 15 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

RDA_IE : Receive Data Reach Interrupt Enable Bit\nThis field is used for received data reaching trigger level RX_FTRI_LEV (SC_CTL[7:6]) interrupt enable.\n
bits : 0 - 0 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

TXBE_IE : Transmit Buffer Empty Interrupt Enable Bit\nThis field is used for transmit buffer empty interrupt enable.\n
bits : 1 - 1 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

TERR_IE : Transfer Error Interrupt Enable Bit\nThis field is used for transfer error interrupt enable. The transfer error states is at SC_SR register which includes receiver break error RX_EBR_F(SC_SR[6]), frame error RX_EFR_F(SC_SR[5]), parity error RX_EPA_F(SC_SR[4]), receiver buffer overflow error RX_OVER_F(SC_SR[0]), transmit buffer overflow error TX_OVER_F(SC_SR[8]), receiver retry over limit error RX_OVER_REERR(SC_SR[22]) and transmitter retry over limit error TX_OVER_REERR(SC_SR[30]).\n
bits : 2 - 2 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

TMR0_IE : Timer0 Interrupt Enable Bit\nThis field is used to enable TMR0 interrupt enable.\n
bits : 3 - 3 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

TMR1_IE : Timer1 Interrupt Enable Bit\nThis field is used to enable the TMR1 interrupt.\n
bits : 4 - 4 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

TMR2_IE : Timer2 Interrupt Enable Bit\nThis field is used for TMR2 interrupt enable.\n
bits : 5 - 5 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

BGT_IE : Block Guard Time Interrupt Enable Bit\nThis field is used for block guard time interrupt enable.\n
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CD_IE : Card Detect Interrupt Enable Bit\nThis field is used for card detect interrupt enable. The card detect status is CD_INS_F(SC_SR[12]) \n
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

INIT_IE : Initial End Interrupt Enable Bit\n
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

RTMR_IE : Receiver Buffer Time-Out Interrupt Enable Bit \nThis field is used for receiver buffer time-out interrupt enable.\n
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

ACON_ERR_IE : Auto Convention Error Interrupt Enable Bit \nThis field is used for auto-convention error interrupt enable.\n
bits : 10 - 10 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

RDA_IS : Receive Data Reach Interrupt Status Flag (Read Only)\nThis field is used for received data reaching trigger level RX_FTRI_LEV (SC_CTL[7:6]) interrupt status flag.\nNote: This field is the status flag of received data reaching RX_FTRI_LEV (SC_CTL[7:6]). If software reads data from SC_RBR and receiver buffer data byte number is less than RX_FTRI_LEV (SC_CTL[7:6]), this bit will be cleared automatically.
bits : 0 - 0 (1 bit)
access : read-only

TBE_IS : Transmit Buffer Empty Interrupt Status Flag (Read Only)\nThis field is used for transmit buffer empty interrupt status flag.\nNote: This field is the status flag of transmit buffer empty state. If software wants to clear this bit, software must write data to THR(SC_THR[7:0]) buffer and then this bit will be cleared automatically.
bits : 1 - 1 (1 bit)
access : read-only

TERR_IS : Transfer Error Interrupt Status Flag (Read Only)\nThis field is used for transfer error interrupt status flag. The transfer error states is at SC_SR register which includes receiver break error RX_EBR_F(SC_SR[6]), frame error RX_EFR_F(SC_TRSR[5], parity error RX_EPA_F(SC_TRSR[4] and receiver buffer overflow error RX_OVER_F(SC_TRSR[0]), transmit buffer overflow error TX_OVER_F(SC_TRSR[8]), receiver retry over limit error RX_OVER_REERR(SC_TRSR[22] and transmitter retry over limit error TX_OVER_REERR(SC_TRSR[30]).\nNote: This field is the status flag of RX_EBR_F(SC_TRSR[6]), RX_EFR_F(SC_TRSR[5]), RX_EPA_F(SC_TRSR[4]), RX_OVER_F(SC_TRSR[0]), TX_OVER_F(SC_TRSR[8]), RX_OVER_REERR(SC_TRSR[22]) or TX_OVER_REERR(SC_TRSR[30]). So, if software wants to clear this bit, software must write 1 to each field.
bits : 2 - 2 (1 bit)
access : read-only

TMR0_IS : Timer0 Interrupt Status Flag (Read Only)\nThis field is used for TMR0 interrupt status flag.\nNote: This bit is read only, but it can be cleared by writing 1 to it.
bits : 3 - 3 (1 bit)
access : read-only

TMR1_IS : Timer1 Interrupt Status Flag (Read Only)\nThis field is used for TMR1 interrupt status flag.\nNote: This bit is read only, but it can be cleared by writing 1 to it.
bits : 4 - 4 (1 bit)
access : read-only

TMR2_IS : Timer2 Interrupt Status Flag (Read Only)\nThis field is used for TMR2 interrupt status flag.\nNote: This bit is read only, but it can be cleared by writing 1 to it.
bits : 5 - 5 (1 bit)
access : read-only

BGT_IS : \n
bits : 6 - 6 (1 bit)
access : read-only

CD_IS : Card Detect Interrupt Status Flag (Read Only)\nThis field is used for card detect interrupt status flag. The card detect status is CD_INS_F (SC_SR[12]) and CD_REM_F(SC_SR[11]).\nNote: This field is the status flag of CD_INS_F(SC_SR[12]) or CD_REM_F(SC_TRSR[11])]. So if software wants to clear this bit, software must write 1 to this field.
bits : 7 - 7 (1 bit)
access : read-only

INIT_IS : Initial End Interrupt Status Flag (Read Only)\nThis field is used for activation (ACT_EN(SC_ALTCTL[3])), deactivation (DACT_EN (SC_ALTCTL[2])) and warm reset (WARST_EN (SC_ALTCTL[4])) sequence interrupt status flag.\nNote: This bit is read only, but it can be cleared by writing 1 to it.
bits : 8 - 8 (1 bit)
access : read-only

RTMR_IS : Receiver Buffer Time-Out Interrupt Status Flag (Read Only)\nThis field is used for receiver buffer time-out interrupt status flag.\nNote: This field is the status flag of receiver buffer time-out state. If software wants to clear this bit, software must read all receiver buffer remaining data by reading SC_RBR buffer,
bits : 9 - 9 (1 bit)
access : read-only

ACON_ERR_IS : Auto Convention Error Interrupt Status Flag (Read Only)\nThis field indicates auto convention sequence error. If the received TS at ATR state is neither 0x3B nor 0x3F, this bit will be set.\nNote: This bit is read only, but it can be cleared by writing 1 to it.
bits : 10 - 10 (1 bit)
access : read-only

RX_OVER_F : RX Overflow Error Status Flag (Read Only) \nThis bit is set when RX buffer overflow.\nIf the number of received bytes is greater than Rx Buffer size (4 bytes), this bit will be set.\nNote: This bit is read only, but it can be cleared by writing 1 to it.
bits : 0 - 0 (1 bit)
access : read-only

RX_EMPTY_F : Receiver Buffer Empty Status Flag(Read Only)\nThis bit indicates RX buffer empty or not.\nWhen the last byte of Rx buffer has been read by CPU, hardware sets this bit high. It will be cleared when SC receives any new data.
bits : 1 - 1 (1 bit)
access : read-only

RX_FULL_F : Receiver Buffer Full Status Flag (Read Only)\nThis bit indicates RX buffer full or not.\nThis bit is set when RX pointer is equal to 4, otherwise it is cleared by hardware.
bits : 2 - 2 (1 bit)
access : read-only

RX_EPA_F : Receiver Parity Error Status Flag (Read Only)\nThis bit is set to logic 1 whenever the received character does not have a valid "parity bit".\nNote1: This bit is read only, but it can be cleared by writing 1 to it.\nNote2: If CPU sets receiver retries function by setting RX_ERETRY_EN(SC_CTL[19]) , hardware will not set this flag.
bits : 4 - 4 (1 bit)
access : read-only

RX_EFR_F : Receiver Frame Error Status Flag (Read Only)\nThis bit is set to logic 1 whenever the received character does not have a valid "stop bit" (that is, the stop bit following the last data bit or parity bit is detected as logic 0). \nNote1: This bit is read only, but it can be cleared by writing 1 to it.\nNote2: If CPU sets receiver retries function by setting RX_ERETRY_EN(SC_CTL[19]) , hardware will not set this flag.
bits : 5 - 5 (1 bit)
access : read-only

RX_EBR_F : Receiver Break Error Status Flag (Read Only)\nThis bit is set to logic 1 whenever the received data input (RX) held in the "spacing state" (logic 0) is longer than a full word transmission time (that is, the total time of "start bit" + data bits + parity + stop bits). .\nNote1: This bit is read only, but it can be cleared by writing 1 to it.\nNote2: If CPU sets receiver retries function by setting RX_ERETRY_EN(SC_CTL[19]) , hardware will not set this flag.
bits : 6 - 6 (1 bit)
access : read-only

TX_OVER_F : TX Overflow Error Interrupt Status Flag (Read Only)\nIf TX buffer is full, an additional write to THR(SC_THR[7:0]) will cause this bit be set to "1" by hardware. \nNote: This bit is read only, but it can be cleared by writing 1 to it.
bits : 8 - 8 (1 bit)
access : read-only

TX_EMPTY_F : Transmit Buffer Empty Status Flag (Read Only)\nThis bit indicates TX buffer empty or not.\nWhen the last byte of TX buffer has been transferred to Transmitter Shift Register, hardware sets this bit high. It will be cleared when writing data into THR(SC_THR[7:0]) (TX buffer not empty).
bits : 9 - 9 (1 bit)
access : read-only

TX_FULL_F : Transmit Buffer Full Status Flag (Read Only)\nThis bit indicates TX buffer full or not.This bit is set when TX pointer is equal to 4, otherwise is cleared by hardware.
bits : 10 - 10 (1 bit)
access : read-only

RX_POINT_F : Receiver Buffer Pointer Status Flag (Read Only)\nThis field indicates the RX buffer pointer status flag. When SC receives one byte from external device, RX_POINT_F(SC_SR[17:16]) increases one. When one byte of RX buffer is read by CPU, RX_POINT_F(SC_SR[17:16]) decreases one.
bits : 16 - 17 (2 bit)
access : read-only

RX_REERR : Receiver Retry Error (Read Only)\nThis bit is set by hardware when RX has any error and retries transfer.\nNote1: This bit is read only, but it can be cleared by writing 1 to it.\nNote2 This bit is a flag and cannot generate any interrupt to CPU.\nNote3: If CPU enables receiver retry function by setting RX_ERETRY_EN (SC_CTL[19]) , the RX_EPA_F(SC_TRSR[4]) flag will be ignored (hardware will not set RX_EPA_F(SC_TRSR[4])).
bits : 21 - 21 (1 bit)
access : read-only

RX_OVER_REERR : Receiver Over Retry Error (Read Only)\nThis bit is set by hardware when RX transfer error retry over retry number limit.\nNote1: This bit is read only, but it can be cleared by writing 1 to it.\nNote2: If CPU enables receiver retries function by setting RX_ERETRY_EN (SC_CTL[19]), the RX_EPA_F(SC_TRSR[4]) flag will be ignored (hardware will not set RX_EPA_F(SC_TRSR[4])).
bits : 22 - 22 (1 bit)
access : read-only

RX_ATV : Receiver In Active Status Flag (Read Only)\nThis bit is set by hardware when RX transfer is in active.\nThis bit is cleared automatically when RX transfer is finished.
bits : 23 - 23 (1 bit)
access : read-only

TX_POINT_F : Transmit Buffer Pointer Status Flag (Read Only)\nThis field indicates the TX buffer pointer status flag. When CPU writes data into SC_THR, TX_POINT_F increases one. When one byte of TX Buffer is transferred to transmitter shift register, TX_POINT_F decreases one.
bits : 24 - 25 (2 bit)
access : read-only

TX_REERR : Transmitter Retry Error (Read Only)\nThis bit is set by hardware when transmitter re-transmits.\nNote1: This bit is read only, but it can be cleared by writing 1 to it.\nNote2 This bit is a flag and cannot generate any interrupt to CPU.
bits : 29 - 29 (1 bit)
access : read-only

TX_OVER_REERR : Transmitter Over Retry Error (Read Only)\nThis bit is set by hardware when transmitter re-transmits over retry number limitation.\nNote: This bit is read only, but it can be cleared by writing 1 to it.
bits : 30 - 30 (1 bit)
access : read-only

TX_ATV : Transmit In Active Status Flag (Read Only)\n
bits : 31 - 31 (1 bit)
access : read-only

Enumeration:

End of enumeration elements list.

POW_EN : SC_POW_EN Pin Signal\nSoftware can set POW_EN (SC_PINCSR[0]) and POW_INV (SC_PINCSR[11])to decide SC_PWR pin is in high or low level.\nWrite this field to drive SC_PWR pin\nRefer POW_INV (SC_PINCSR[11]) description for programming SC_PWR pin voltage level. \nRead this field to get SC_PWR pin status.\nNote: When operating at activation, warm reset or deactivation mode, this bit will be changed automatically. So don't fill this field when operating in these modes.
bits : 0 - 0 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

SC_RST : SC_RST Pin Signal\nThis bit is the pin status of SC_RST but user can drive SC_RST pin to high or low by setting this bit.\nWrite this field to drive SC_RST pin.\nNote: When operating at activation, warm reset or deactivation mode, this bit will be changed automatically. So don't fill this field when operating in these modes.
bits : 1 - 1 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CD_REM_F : Card Detect Removal Status Of SC_CD Pin (Read Only)\nThis bit is set whenever a card has been removed.\nNote1: This bit is read only, but it can be cleared by writing "1" to it.\nNote2: Card detect engine will start after SC_CEN (SC_CTL[0] )set.
bits : 2 - 2 (1 bit)
access : read-only

Enumeration:

End of enumeration elements list.

CD_INS_F : Card Detect Insert Status Of SC_CD Pin (Read Only)\nThis bit is set whenever card has been inserted.\nNote1: This bit is read only, but it can be cleared by writing "1" to it.\nNote2: The card detect engine will start after SC_CEN (SC_CTL[0] )set.
bits : 3 - 3 (1 bit)
access : read-only

Enumeration:

End of enumeration elements list.

CD_PIN_ST : Card Detect Status Of SC_CD Pin Status (Read Only)\nThis bit is the pin status flag of SC_CD\n
bits : 4 - 4 (1 bit)
access : read-only

Enumeration:

End of enumeration elements list.

CLK_KEEP : SC Clock Enable Bit \nNote: When operating in activation, warm reset or deactivation mode, this bit will be changed automatically. So don't fill this field when operating in these modes.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

ADAC_CD_EN : Auto Deactivation When Card Removal\nNote: When the card is removed, hardware will stop any process and then do deactivation sequence (if this bit be setting). If this process completes. Hardware will generate an initial end interrupt to CPU.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

SC_OEN_ST : SC Data Output Enable Pin Status (Read Only)\nThis bit is the pin status of SC_DATA_OEN\n
bits : 8 - 8 (1 bit)
access : read-only

Enumeration:

End of enumeration elements list.

SC_DATA_O : SC Data Output Pin \nThis bit is the pin status of SC_DATA_O but user can drive SC_DATA_O pin to high or low by setting this bit.\nNote: When SC is at activation, warm reset or deactivation mode, this bit will be changed automatically. So don't fill this field when SC is in these modes.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CD_LEV : Card Detect Level\n\nNote: Software must select card detect level before Smart Card engine is enabled
bits : 10 - 10 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

POW_INV : SC_POW Pin Inverse\nThis bit is used for inverse the SC_POW pin.\nThere are four kinds of combination for SC_POW pin setting by POW_INV(SC_PINCSR[11]) and POW_EN(SC_PINCSR[0]). POW_INV (SC_PINCSR[11]) is bit 1 and POW_EN(SC_PINCSR[0]) is bit 0 for SC_POW_Pin as high or low voltage selection.\nNote: Software must select POW_INV (SC_PINCSR[11]) before Smart Card is enabled by SC_CEN (SC_CTL[0]).
bits : 11 - 11 (1 bit)
access : read-write

SC_DATA_I_ST : SC Data Pin Status (Read Only)\nThis bit is the pin status of SC_DATA\n
bits : 16 - 16 (1 bit)
access : read-only

Enumeration:

End of enumeration elements list.

SYNC : SYNC Flag Indicator\nDue to synchronization, software should check this bit when writing a new value to SC_PINCSR register.\nNote: This bit is read only.
bits : 30 - 30 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CNT0 : Timer 0 Counter Value (ETU Base)\nThis field indicates the internal timer operation values.
bits : 0 - 23 (24 bit)
access : read-write

MODE : Timer 0 Operation Mode Selection\nThis field indicates the internal 24-bit timer operation selection.\nRefer to 6.14.5.4 for programming Timer0
bits : 24 - 27 (4 bit)
access : read-write

CNT1 : Timer 1 Counter Value (ETU Base)\nThis field indicates the internal timer operation values.
bits : 0 - 7 (8 bit)
access : read-write

MODE : Timer 1 Operation Mode Selection\nThis field indicates the internal 8-bit timer operation selection.\nRefer to 6.14.5.4 for programming Timer1
bits : 24 - 27 (4 bit)
access : read-write

CNT2 : Timer 2 Counter Value (ETU Base)\nThis field indicates the internal timer operation values.
bits : 0 - 7 (8 bit)
access : read-write

MODE : Timer 2 Operation Mode Selection\nThis field indicates the internal 8-bit timer operation selection\nRefer to 6.14.5.4 for programming Timer2
bits : 24 - 27 (4 bit)
access : read-write

UA_MODE_EN : UART Mode Enable Bit\nNote3: When UART is enabled, hardware will generate a reset to reset FIFO and internal state machine.
bits : 0 - 0 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

DATA_LEN : Data Length\nNote: In smart card mode, this DATA_LEN must be '00'
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

End of enumeration elements list.

PBDIS : Parity Bit Disable Bit\nNote: In smart card mode, this field must be '0' (default setting is with parity bit)
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

OPE : Odd Parity Enable Bit\nNote: This bit has effect only when PBDIS bit is '0'.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

TDR0 : Timer0 Current Data Value(Read Only)\nThis field indicates the current count values of timer0.
bits : 0 - 23 (24 bit)
access : read-only

TDR1 : Timer1 Current Data Value(Read Only)\nThis field indicates the current count values of timer1.
bits : 0 - 7 (8 bit)
access : read-only

TDR2 : Timer2 Current Data Value (Read Only)\nThis field indicates the current count values of timer2.
bits : 8 - 15 (8 bit)
access : read-only

SC_CEN : SC Engine Enable Bit\nSet this bit to 1 to enable SC operation. If this bit is cleared, SC will force all transition to IDLE state.
bits : 0 - 0 (1 bit)
access : read-write

DIS_RX : RX Transition Disable Bit\nNote: If AUTO_CON_EN (SC_CTL[3])is enabled, these fields must be ignored.
bits : 1 - 1 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

DIS_TX : TX Transition Disable Bit\n
bits : 2 - 2 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

AUTO_CON_EN : Auto Convention Enable Bit\n
bits : 3 - 3 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CON_SEL : Convention Selection\nNote: If AUTO_CON_EN(SC_CTL[3]) enabled, this fields are ignored.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

End of enumeration elements list.

RX_FTRI_LEV : Rx Buffer Trigger Level \nWhen the number of bytes in the receiving buffer equals the RX_FTRI_LEV, the RDA_IF will be set (if IER [RDA_IEN] is enabled, an interrupt will be generated).\n
bits : 6 - 7 (2 bit)
access : read-write

Enumeration:

End of enumeration elements list.

BGT : Block Guard Time (BGT)\nNote: The real block guard time is BGT + 1.
bits : 8 - 12 (5 bit)
access : read-write

TMR_SEL : Timer Selection \n
bits : 13 - 14 (2 bit)
access : read-write

Enumeration:

End of enumeration elements list.

SLEN : Stop Bit Length\nThis field indicates the length of stop bit.\nNote: The default stop bit length is 2. SMC and UART adopts SLEN to program the stop bit length
bits : 15 - 15 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

RX_ERETRY : RX Error Retry Count Number\nThis field indicates the maximum number of receiver retries that are allowed when parity error has occurred\nNote1: The real retry number is RX_ERETRY + 1, so 8 is the maximum retry number.\nNote2: This field cannot be changed when RX_ERETRY_EN enabled. The change flow is to disable RX_ETRTRY_EN first and then fill in new retry value.
bits : 16 - 18 (3 bit)
access : read-write

RX_ERETRY_EN : RX Error Retry Enable Bit\nThis bit enables receiver retry function when parity error has occurred.\nNote: Software must fill in the RX_ERETRY value before enabling this bit.
bits : 19 - 19 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

TX_ERETRY : TX Error Retry Count Number\nThis field indicates the maximum number of transmitter retries that are allowed when parity error has occurred.\nNote1: The real retry number is TX_ERETRY + 1, so 8 is the maximum retry number.\nNote2: This field cannot be changed when TX_ERETRY_EN enabled. The change flow is to disable TX_ETRTRY_EN first and then fill in new retry value.
bits : 20 - 22 (3 bit)
access : read-write

TX_ERETRY_EN : TX Error Retry Enable Bit\nThis bit enables transmitter retry function when parity error has occurred.\n
bits : 23 - 23 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CD_DEB_SEL : Card Detect De-Bounce Selection\nThis field indicates the card detect de-bounce selection.\n
bits : 24 - 25 (2 bit)
access : read-write

Enumeration:

End of enumeration elements list.

SYNC : SYNC Flag Indicator\nDue to synchronization, software should check this bit before writing a new value to RX_ERETRY and TX_ERETRY.\nNote: This bit is read only.
bits : 30 - 30 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

TX_RST : TX Software Reset\nWhen TX_RST is set, all the bytes in the transmit buffer and TX internal state machine will be cleared.\nNote: This bit will be auto cleared after reset is complete.
bits : 0 - 0 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

RX_RST : Rx Software Reset\nWhen RX_RST is set, all the bytes in the receiver buffer and Rx internal state machine will be cleared.\nNote: This bit will be auto cleared after reset is complete.
bits : 1 - 1 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

DACT_EN : Deactivation Sequence Generator Enable Bit\nThis bit enables SC controller to initiate the card by deactivation sequence\nNote1: When the deactivation sequence completed, this bit will be cleared automatically and the INIT_IS(SC_ISR[8]) will be set to 1.\nNote2: This field will be cleared by TX_RST (SC_ALTCTL[0]) and RX_RST(SC_ALTCTL[1]). So don't fill this bit, TX_RST, and RX_RST at the same time.\nNote3: If SC_CEN (SC_CTL[0]) is not enabled, this filed cannot be programmed.
bits : 2 - 2 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

ACT_EN : Activation Sequence Generator Enable Bit\nThis bit enables SC controller to initiate the card by activation sequence\nNote1: When the activation sequence completed, this bit will be cleared automatically and the INIT_IS(SC_ISR[8]) will be set to 1.\nNote2: This field will be cleared by TX_RST(SC_ALTCTL[0]) and RX_RST(SC_ALTCTL[1]), so don't fill this bit, TX_RST(SC_ALTCTL[0]), and RX_RST(SC_ALTCTL[1]) at the same time.\nNote3: If SC_CEN(SC_CTL[0]) is not enabled, this filed cannot be programmed.
bits : 3 - 3 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

WARST_EN : Warm Reset Sequence Generator Enable Bit\nThis bit enables SC controller to initiate the card by warm reset sequence\nNote1: When the warm reset sequence completed, this bit will be cleared automatically and the INIT_IS(SC_ISR[8]) will be set to 1.\nNote2: This field will be cleared by TX_RST(SC_ALTCTL[0]) and RX_RST(SC_ALTCTL[1]), so don't fill this bit, TX_RST, and RX_RST at the same time.\nNote3: If SC_CEN(SC_CTL[0]) is not enabled, this filed cannot be programmed.
bits : 4 - 4 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

TMR0_SEN : Internal Timer0 Start Enable Bit\nThis bit enables Timer 0 to start counting. Software can fill 0 to stop it and set 1 to reload and count.\nNote3: This field will be cleared by TX_RST(SC_ALTCTL[0]) and RX_RST(SC_ALTCTL[1]). So don't fill this bit, TX_RST and RX_RST at the same time.\nNote4: If SC_CEN(SC_CTL[0]) is not enabled, this filed cannot be programmed.
bits : 5 - 5 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

TMR1_SEN : Internal Timer1 Start Enable Bit\nThis bit enables Timer 1 to start counting. Software can fill 0 to stop it and set 1 to reload and count.\nNote3: This field will be cleared by TX_RST(SC_ALTCTL[0]) and RX_RST(SC_ALTCTL[1]), so don't fill this bit, TX_RST(SC_ALTCTL[0]), and RX_RST(SC_ALTCTL[1]) at the same time.\nNote4: If SC_CEN(SC_CTL[0]) is not enabled, this filed cannot be programmed.
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

TMR2_SEN : Internal Timer2 Start Enable Bit\nThis bit enables Timer 2 to start counting. Software can fill 0 to stop it and set 1 to reload and count.\nNote3: This field will be cleared by TX_RST(SC_ALTCTL[0]) and RX_RST(SC_ALTCTL[1]). So don't fill this bit, TX_RST(SC_ALTCTL[0]), and RX_RST(SC_ALTCTL[1]) at the same time.\nNote4: If SC_CEN(SC_CTL[0]) is not enabled, this filed cannot be programmed.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

INIT_SEL : Initial Timing Selection\nThis fields indicates the timing of hardware initial state (activation or warm-reset or deactivation).\nUnit: SC clock\nActivation: refer to SC Activation Sequence in Figure 679.\nWarm-reset: refer to Warm-Reset Sequence in Figure 680.\nDeactivation: refer to Deactivation Sequence in Figure 681.
bits : 8 - 9 (2 bit)
access : read-write

RX_BGT_EN : Receiver Block Guard Time Function Enable Bit\n
bits : 12 - 12 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

TMR0_ATV : Internal Timer0 Active State (Read Only)\nThis bit indicates the timer counter status of timer0.\n
bits : 13 - 13 (1 bit)
access : read-only

Enumeration:

End of enumeration elements list.

TMR1_ATV : Internal Timer1 Active State (Read Only)\nThis bit indicates the timer counter status of timer1.\n
bits : 14 - 14 (1 bit)
access : read-only

Enumeration:

End of enumeration elements list.

TMR2_ATV : Internal Timer2 Active State (Read Only)\nThis bit indicates the timer counter status of timer2.\n
bits : 15 - 15 (1 bit)
access : read-only

Enumeration:

End of enumeration elements list.

OUTSEL : Smartcard Data Pin Output Mode Selection\nUse this bit to select smartcard data pin (SC_DATA) output mode\n
bits : 16 - 16 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

EGT : Extended Guard Time\nThis field indicates the extended guard timer value.\nNote: The counter is ETU base and the real extended guard time is EGT.
bits : 0 - 7 (8 bit)
access : read-write