Embeetle, an IDE designed from scratch for embedded software developers.address_offset : 0x0 Bytes (0x0)
size : 0x200 byte (0x0)
mem_usage : registers
protection : not protected
address_offset : 0x0 Bytes (0x0)
size : 0x200 byte (0x0)
mem_usage : registers
protection :
POEG Group %s Setting Register
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PIDF : Port Input Detection Flag
bits : 0 - -1 (0 bit)
access : read-write
Enumeration:
#0 : 0
No output-disable request from the GTETRGn pin has occurred
#1 : 1
Output-disable request from the GTETRGn pin occurred.
End of enumeration elements list.
IOCF : Output-disable Request Detection Flag from GPT
bits : 1 - 0 (0 bit)
access : read-write
Enumeration:
#0 : 0
No output-disable request from the GPT disable request has occurred
#1 : 1
Output-disable request from the GPT disable request occurred.
End of enumeration elements list.
OSTPF : Oscillation Stop Detection Flag
bits : 2 - 1 (0 bit)
access : read-write
Enumeration:
#0 : 0
No output-disable request from oscillation stop detection has occurred
#1 : 1
Output-disable request from oscillation stop detection occurred.
End of enumeration elements list.
SSF : Software Stop Flag
bits : 3 - 2 (0 bit)
access : read-write
Enumeration:
#0 : 0
No output-disable request from software has occurred
#1 : 1
Output-disable request from software occurred.
End of enumeration elements list.
PIDE : Port Input Detection EnableNote: Can be modified only once after a reset.
bits : 4 - 3 (0 bit)
access : read-write
Enumeration:
#0 : 0
Output-disable request from the GTETRG pins disabled
#1 : 1
Output-disable request from the GTETRG pins enabled.
End of enumeration elements list.
IOCE : Output-disable Request Enable from GPTNote: Can be modified only once after a reset.
bits : 5 - 4 (0 bit)
access : read-write
Enumeration:
#0 : 0
Output-disable request from the GPT disable request disabled
#1 : 1
Output-disable request from the GPT disable request enabled.
End of enumeration elements list.
OSTPE : Oscillation Stop Detection EnableNote: Can be modified only once after a reset.
bits : 6 - 5 (0 bit)
access : read-write
Enumeration:
#0 : 0
A output-disable request from the oscillation stop detection disabled.
#1 : 1
A output-disable request from the oscillation stop detection enabled.
End of enumeration elements list.
ST : GTETRG Input Status Flag
bits : 16 - 15 (0 bit)
access : read-only
Enumeration:
#0 : 0
GTETRG input after filtering is 0.
#1 : 1
GTETRG input after filtering is 1.
End of enumeration elements list.
Reserved : These bits are read as 00000000000. The write value should be 00000000000.
bits : 17 - 26 (10 bit)
access : read-write
INV : GTETRG Input Reverse
bits : 28 - 27 (0 bit)
access : read-write
Enumeration:
#0 : 0
GTETRG Input
#1 : 1
GTETRG Input Reversed.
End of enumeration elements list.
NFEN : Noise Filter Enable
bits : 29 - 28 (0 bit)
access : read-write
Enumeration:
#0 : 0
Filtering noise disabled
#1 : 1
Filtering noise enabled
End of enumeration elements list.
NFCS : Noise Filter Clock Select
bits : 30 - 30 (1 bit)
access : read-write
Enumeration:
#00 : 00
Sampling GTETRG pin input level for three times in every PCLKB.
#01 : 01
Sampling GTETRG pin input level for three times in every PCLKB /8.
#10 : 10
Sampling GTETRG pin input level for three times in every PCLKB /32.
#11 : 11
Sampling GTETRG pin input level for three times in every PCLKB /128.
End of enumeration elements list.
POEG Group %s Setting Register
address_offset : 0x100 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PIDF : Port Input Detection Flag
bits : 0 - -1 (0 bit)
access : read-write
Enumeration:
#0 : 0
No output-disable request from the GTETRGn pin has occurred
#1 : 1
Output-disable request from the GTETRGn pin occurred.
End of enumeration elements list.
IOCF : Output-disable Request Detection Flag from GPT
bits : 1 - 0 (0 bit)
access : read-write
Enumeration:
#0 : 0
No output-disable request from the GPT disable request has occurred
#1 : 1
Output-disable request from the GPT disable request occurred.
End of enumeration elements list.
OSTPF : Oscillation Stop Detection Flag
bits : 2 - 1 (0 bit)
access : read-write
Enumeration:
#0 : 0
No output-disable request from oscillation stop detection has occurred
#1 : 1
Output-disable request from oscillation stop detection occurred.
End of enumeration elements list.
SSF : Software Stop Flag
bits : 3 - 2 (0 bit)
access : read-write
Enumeration:
#0 : 0
No output-disable request from software has occurred
#1 : 1
Output-disable request from software occurred.
End of enumeration elements list.
PIDE : Port Input Detection EnableNote: Can be modified only once after a reset.
bits : 4 - 3 (0 bit)
access : read-write
Enumeration:
#0 : 0
Output-disable request from the GTETRG pins disabled
#1 : 1
Output-disable request from the GTETRG pins enabled.
End of enumeration elements list.
IOCE : Output-disable Request Enable from GPTNote: Can be modified only once after a reset.
bits : 5 - 4 (0 bit)
access : read-write
Enumeration:
#0 : 0
Output-disable request from the GPT disable request disabled
#1 : 1
Output-disable request from the GPT disable request enabled.
End of enumeration elements list.
OSTPE : Oscillation Stop Detection EnableNote: Can be modified only once after a reset.
bits : 6 - 5 (0 bit)
access : read-write
Enumeration:
#0 : 0
A output-disable request from the oscillation stop detection disabled.
#1 : 1
A output-disable request from the oscillation stop detection enabled.
End of enumeration elements list.
ST : GTETRG Input Status Flag
bits : 16 - 15 (0 bit)
access : read-only
Enumeration:
#0 : 0
GTETRG input after filtering is 0.
#1 : 1
GTETRG input after filtering is 1.
End of enumeration elements list.
Reserved : These bits are read as 00000000000. The write value should be 00000000000.
bits : 17 - 26 (10 bit)
access : read-write
INV : GTETRG Input Reverse
bits : 28 - 27 (0 bit)
access : read-write
Enumeration:
#0 : 0
GTETRG Input
#1 : 1
GTETRG Input Reversed.
End of enumeration elements list.
NFEN : Noise Filter Enable
bits : 29 - 28 (0 bit)
access : read-write
Enumeration:
#0 : 0
Filtering noise disabled
#1 : 1
Filtering noise enabled
End of enumeration elements list.
NFCS : Noise Filter Clock Select
bits : 30 - 30 (1 bit)
access : read-write
Enumeration:
#00 : 00
Sampling GTETRG pin input level for three times in every PCLKB.
#01 : 01
Sampling GTETRG pin input level for three times in every PCLKB /8.
#10 : 10
Sampling GTETRG pin input level for three times in every PCLKB /32.
#11 : 11
Sampling GTETRG pin input level for three times in every PCLKB /128.
End of enumeration elements list.
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.