Embeetle, an IDE designed from scratch for embedded software developers.address_offset : 0x0 Bytes (0x0)
size : 0x3 byte (0x0)
mem_usage : registers
protection : not protected
address_offset : 0x4 Bytes (0x0)
size : 0x2 byte (0x0)
mem_usage : registers
protection : not protected
ACMPLP Mode Setting Register
address_offset : 0x0 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
C0ENB : ACMPLP0 Operation Enable
bits : 0 - -1 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
C0WDE : ACMPLP0 Window Function Mode Enable
bits : 1 - 0 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
C0VRF : ACMPLP0 Reference Voltage Selection
bits : 2 - 1 (0 bit)
access : read-write
Enumeration:
#0 : 0
IVREF0
#1 : 1
internal reference voltage (Vref)
End of enumeration elements list.
C0MON : ACMPLP0 Monitor Flag
bits : 3 - 2 (0 bit)
access : read-only
Enumeration:
#0 : 0
CMPIN0 < CMPREF0, CMPIN0 < internal reference voltage, or ACMPLP0 operation disabled.(When the window function is disabled)/CMPIN0 < VRFL, CMPIN0 > VRFH, or ACMPLP0 operation disabled.(When the window function is enabled)
#1 : 1
CMPIN0 > CMPREF0, or CMPIN0 > internal reference voltage.(When the window function is disabled)/VRFL < CMPIN0 < VRFH.(When the window function is enabled)
End of enumeration elements list.
C1ENB : ACMPLP1 Operation Enable
bits : 4 - 3 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
C1WDE : ACMPLP1 Window Function Mode Enable
bits : 5 - 4 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
C1VRF : ACMPLP1 Reference Voltage Selection
bits : 6 - 5 (0 bit)
access : read-write
Enumeration:
#0 : 0
IVREF0 or IVREF1
#1 : 1
internal reference voltage (Vref)
End of enumeration elements list.
C1MON : ACMPLP1 Monitor Flag
bits : 7 - 6 (0 bit)
access : read-only
Enumeration:
#0 : 0
CMPIN1 < CMPREF1, CMPIN1 < internal reference voltage, or ACMPLP1 operation disabled.(When the window function is disabled)/CMPIN1 < VRFL, CMPIN1 > VRFH, or ACMPLP1 operation disabled.(When the window function is enabled)
#1 : 1
CMPIN1 > CMPREF1, or CMPIN1 > internal reference voltage.(When the window function is disabled)/VRFL < CMPIN1 < VRFH.(When the window function is enabled)
End of enumeration elements list.
ACMPLP Filter Control Register
address_offset : 0x1 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
C0FCK : ACMPLP0 Filter Select
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#00 : 00
No Sampling (bypass)
#01 : 01
Sampling at PCLK
#10 : 10
Sampling at PCLK/8
#11 : 11
Sampling at PCLK/32
End of enumeration elements list.
C0EPO : ACMPLP0 Edge Polarity Switching
bits : 2 - 1 (0 bit)
access : read-write
Enumeration:
#0 : 0
Interrupt and ELC event request at rising edge
#1 : 1
Interrupt and ELC event request at falling edge
End of enumeration elements list.
C0EDG : ACMPLP0 Edge Detection Selection
bits : 3 - 2 (0 bit)
access : read-write
Enumeration:
#0 : 0
Interrupt and ELC event request by one-edge detection
#1 : 1
Interrupt and ELC event request by both-edge detection
End of enumeration elements list.
C1FCK : ACMPLP1 Filter Select
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#00 : 00
No Sampling (bypass)
#01 : 01
Sampling at PCLK
#10 : 10
Sampling at PCLK/8
#11 : 11
Sampling at PCLK/32
End of enumeration elements list.
C1EPO : ACMPLP1 Edge Polarity Switching
bits : 6 - 5 (0 bit)
access : read-write
Enumeration:
#0 : 0
Interrupt and ELC event request at rising edge
#1 : 1
Interrupt and ELC event request at falling edge
End of enumeration elements list.
C1EDG : ACMPLP1 Edge Detection Selection
bits : 7 - 6 (0 bit)
access : read-write
Enumeration:
#0 : 0
Interrupt and ELC event request by one-edge detection
#1 : 1
Interrupt and ELC event request by both-edge detection
End of enumeration elements list.
ACMPLP Output Control Register
address_offset : 0x2 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
C0OE : ACMPLP0 VCOUT Pin Output Enable
bits : 1 - 0 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
C0OP : ACMPLP0 VCOUT Output Polarity Selection
bits : 2 - 1 (0 bit)
access : read-write
Enumeration:
#0 : 0
Non inverted
#1 : 1
Inverted
End of enumeration elements list.
Reserved : These bits are read as 00. The write value should be 00.
bits : 3 - 3 (1 bit)
access : read-write
Reserved : These bits are read as 00. The write value should be 00.
bits : 3 - 3 (1 bit)
access : read-write
C1OE : ACMPLP1 VCOUT Pin Output Enable
bits : 5 - 4 (0 bit)
access : read-write
Enumeration:
#0 : 0
Disabled
#1 : 1
Enabled
End of enumeration elements list.
C1OP : ACMPLP1 VCOUT Output Polarity Selection
bits : 6 - 5 (0 bit)
access : read-write
Enumeration:
#0 : 0
Non inverted
#1 : 1
Inverted
End of enumeration elements list.
SPDMD : ACMPLP0/ACMPLP1 Speed Selection
bits : 7 - 6 (0 bit)
access : read-write
Enumeration:
#0 : 0
Comparator low-speed mode
#1 : 1
Comparator high-speed mode
End of enumeration elements list.
Comparator Input Select Register
address_offset : 0x4 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CMPSEL20 : ACMPLP0 Input(IVCMP0) Selection
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
#000 : 000
No input
#001 : 001
CMPIN0 (P100)
#100 : 100
CMPIN0 (P503)
End of enumeration elements list.
CMPSEL64 : ACMPLP1 Input (IVCMP1) Selection
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#000 : 000
No input
#001 : 001
CMPIN1 (P102)
#100 : 100
CMPIN1 (P501)
End of enumeration elements list.
Reserved : This bit is read as 0. The write value should be 0.
bits : 7 - 6 (0 bit)
access : read-write
Reserved : This bit is read as 0. The write value should be 0.
bits : 7 - 6 (0 bit)
access : read-write
Comparator Reference Voltage Select Register
address_offset : 0x5 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CRVS20 : ACMPLP0 Reference Voltage(IVREF0) Selection*
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
#000 : 000
No input
#001 : 001
CMPREF0 (P101)
#010 : 010
DAC8 (ch0) output
#100 : 100
CMPREF0 (P502)
End of enumeration elements list.
Reserved : This bit is read as 0. The write value should be 0.
bits : 3 - 2 (0 bit)
access : read-write
CRVS64 : ACMPLP1 Reference Voltage(IVREF1) Selection
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
#000 : 000
No input
#001 : 001
CMPREF1 (P103)
#010 : 010
DAC8 (ch1) output
#100 : 100
CMPREF1 (P500)
End of enumeration elements list.
C1VRF2 : ACMPLP1 Reference Voltage Selection
bits : 7 - 6 (0 bit)
access : read-write
Enumeration:
#0 : 0
IVREF0 selected
#1 : 1
IVREF1 selected.
End of enumeration elements list.
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.