Embeetle, an IDE designed from scratch for embedded software developers.address_offset : 0x0 Bytes (0x0)
size : 0xC byte (0x0)
mem_usage : registers
protection : not protected
Module Stop Control Register B
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
Reserved : This bit is read as 1. The write value should be 1.
bits : 0 - -1 (0 bit)
access : read-write
MSTPB1 : RCAN1 Module Stop
bits : 1 - 0 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPB2 : RCAN0 Module Stop
bits : 2 - 1 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
Reserved : These bits are read as 11. The write value should be 11.
bits : 3 - 3 (1 bit)
access : read-write
MSTPB5 : IrDA Module Stop
bits : 5 - 4 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPB6 : Queued Serial Peripheral Interface Module Stop
bits : 6 - 5 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPB7 : I2C Bus Interface 2 Module Stop
bits : 7 - 6 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPB8 : I2C Bus Interface 1 Module Stop
bits : 8 - 7 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPB9 : I2C Bus Interface 0 Module Stop
bits : 9 - 8 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
Reserved : This bit is read as 1. The write value should be 1.
bits : 10 - 9 (0 bit)
access : read-write
MSTPB11 : Universal Serial Bus 2.0 FS Interface Module Stop
bits : 11 - 10 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPB12 : Universal Serial Bus 2.0 HS Interface Module Stop
bits : 12 - 11 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPB13 : EPTPC and PTPEDMAC Module Stop
bits : 13 - 12 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPB14 : ETHERC1 and EDMAC1 Module Stop
bits : 14 - 13 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPB15 : ETHERC0 and EDMAC0 Module Stop
bits : 15 - 14 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
Reserved : These bits are read as 11. The write value should be 11.
bits : 16 - 16 (1 bit)
access : read-write
MSTPB18 : Serial Peripheral Interface Module Stop
bits : 18 - 17 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPB19 : Serial Peripheral Interface 0 Module Stop
bits : 19 - 18 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
Reserved : These bits are read as 11. The write value should be 11.
bits : 20 - 20 (1 bit)
access : read-write
MSTPB22 : Serial Communication Interface 9 Module Stop
bits : 22 - 21 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPB23 : Serial Communication Interface 8 Module Stop
bits : 23 - 22 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPB24 : Serial Communication Interface 7 Module Stop
bits : 24 - 23 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPB25 : Serial Communication Interface 6 Module Stop
bits : 25 - 24 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPB26 : Serial Communication Interface 5 Module Stop
bits : 26 - 25 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPB27 : Serial Communication Interface 4 Module Stop
bits : 27 - 26 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPB28 : Serial Communication Interface 3 Module Stop
bits : 28 - 27 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPB29 : Serial Communication Interface 2 Module Stop
bits : 29 - 28 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPB30 : Serial Communication Interface 1 Module Stop
bits : 30 - 29 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPB31 : Serial Communication Interface 0 Module Stop
bits : 31 - 30 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
Module Stop Control Register C
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MSTPC0 : CAC Module Stop
bits : 0 - -1 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPC1 : CRC Calculator Module Stop
bits : 1 - 0 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPC3 : Capacitive Touch Sensing Unit Module Stop
bits : 3 - 2 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPC13 : Data Operation Circuit Module Stop
bits : 13 - 12 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPC14 : Event Link Controller Module Stop
bits : 14 - 13 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPC28 : Random Number Generator Module Stop
bits : 28 - 27 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state.
End of enumeration elements list.
MSTPC31 : AES Module Stop
bits : 31 - 30 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
Module Stop Control Register D
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MSTPD2 : AGT1 Module StopNote: AGT1 is in the module stop state when the count source is either of PCLKB, PCLKB/2 or PCLKB/8. In case the count source is sub-clock or LOCO, this bit should be set to 1 except when accessing the registers of AGT1.
bits : 2 - 1 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPD3 : AGT0 Module StopNote: AGT0 is in the module stop state when the count source is either of PCLKB, PCLKB/2 or PCLKB/8. In case the count source is sub-clock or LOCO, this bit should be set to 1 except when accessing the registers of AGT0.
bits : 3 - 2 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPD5 : GPT ch0 Module Stop
bits : 5 - 4 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPD6 : GPT ch6 - ch1 Module Stop
bits : 6 - 5 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPD14 : POEG Module Stop
bits : 14 - 13 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPD16 : 16-Bit A/D Converter Module Stop
bits : 16 - 15 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPD17 : 24-bit Sigma-Delta A/DConverter Module Stop
bits : 17 - 16 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPD19 : 8-Bit D/A Converter Module Stop
bits : 19 - 18 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPD20 : 12-bit D/A Converter Module Stop
bits : 20 - 19 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPD28 : ACMPHS0 Module Stop
bits : 28 - 27 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPD29 : Comparator-LP Module Stop
bits : 29 - 28 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
MSTPD31 : Operational Amplifier Module Stop
bits : 31 - 30 (0 bit)
access : read-write
Enumeration:
#0 : 0
Cancel the module-stop state
#1 : 1
Enter the module-stop state
End of enumeration elements list.
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.