\n

R_RTC

Peripheral Memory Blocks

address_offset : 0x0 Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x4 Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x14 Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x18 Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x28 Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x44 Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x54 Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x64 Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x8 Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0xC Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x5C Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x24 Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x40 Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x6C Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x74 Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x7C Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x2 Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x6 Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0xA Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0xE Bytes (0x0)
size : 0x3 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x12 Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x16 Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x1A Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x1C Bytes (0x0)
size : 0x3 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x22 Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x2A Bytes (0x0)
size : 0x5 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x52 Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x7A Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x42 Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x56 Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x5A Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x62 Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x66 Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x6A Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x72 Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

address_offset : 0x76 Bytes (0x0)
size : 0x1 byte (0x0)
mem_usage : registers
protection : not protected

Registers

R64CNT

RSECAR

BCNT0AR

RMINAR

BCNT1AR

CP[2]-CP[1]-CP[0]-RSEC

CP[2]-CP[1]-CP[0]-BCNT0

CP[2]-CP[1]-CP[0]-RMIN

CP[2]-CP[1]-CP[0]-BCNT1

CP[2]-CP[1]-CP[0]-RHR

CP[2]-CP[1]-CP[0]-BCNT2

CP[2]-CP[1]-CP[0]-RDAY

CP[2]-CP[1]-CP[0]-BCNT3

CP[2]-CP[1]-CP[0]-RMON

RHRAR

BCNT2AR

RWKAR

BCNT3AR

RDAYAR

BCNT0AER

RMONAR

BCNT1AER

RYRAR

BCNT2AER

RYRAREN

BCNT3AER

RSECCNT

BCNT0

RCR1

RCR2

RCR4

RFRH

RFRL

RADJ

RMINCNT

BCNT1

RTCCR[0]-RTCCR

CP[0]-RSEC

CP[0]-BCNT0

CP[0]-RMIN

CP[0]-BCNT1

CP[0]-RHR

CP[0]-BCNT2

CP[0]-RDAY

CP[0]-BCNT3

CP[0]-RMON

RHRCNT

BCNT2

RWKCNT

BCNT3

RTCCR[1]-RTCCR[0]-RTCCR

RDAYCNT

CP[1]-CP[0]-RSEC

CP[1]-CP[0]-BCNT0

CP[1]-CP[0]-RMIN

CP[1]-CP[0]-BCNT1

CP[1]-CP[0]-RHR

CP[1]-CP[0]-BCNT2

CP[1]-CP[0]-RDAY

CP[1]-CP[0]-BCNT3

CP[1]-CP[0]-RMON

RMONCNT

RTCCR[2]-RTCCR[1]-RTCCR[0]-RTCCR

RYRCNT


R64CNT

64-Hz Counter
address_offset : 0x0 Bytes (0x0)
size : 8 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0

R64CNT R64CNT read-only 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 F64HZ F32HZ F16HZ F8HZ F4HZ F2HZ F1HZ

F64HZ : 64Hz
bits : 0 - -1 (0 bit)
access : read-only

F32HZ : 32Hz
bits : 1 - 0 (0 bit)
access : read-only

F16HZ : 16Hz
bits : 2 - 1 (0 bit)
access : read-only

F8HZ : 8Hz
bits : 3 - 2 (0 bit)
access : read-only

F4HZ : 4Hz
bits : 4 - 3 (0 bit)
access : read-only

F2HZ : 2Hz
bits : 5 - 4 (0 bit)
access : read-only

F1HZ : 1Hz
bits : 6 - 5 (0 bit)
access : read-only


RSECAR

Second Alarm Register
address_offset : 0x10 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RSECAR RSECAR read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 SEC1 SEC10 ENB

SEC1 : 1-Second Value for the ones place of seconds
bits : 0 - 2 (3 bit)
access : write-only

SEC10 : 10-Seconds Value for the tens place of seconds
bits : 4 - 5 (2 bit)
access : read-write

ENB : Compare enable
bits : 7 - 6 (0 bit)
access : read-write

Enumeration:

#0 : 0

The register value is not compared with the RSECCNT counter value.

#1 : 1

The register value is compared with the RSECCNT counter value.

End of enumeration elements list.


BCNT0AR

Binary Counter 0 Alarm Register
address_offset : 0x10 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
alternate_register : RSECAR
reset_Mask : 0x0

BCNT0AR BCNT0AR read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 BCNT0AR

BCNT0AR : he BCNT0AR counter is a readable/writable alarm register corresponding to 32-bit binary counter b7 to b0.
bits : 0 - 6 (7 bit)
access : read-write


RMINAR

Minute Alarm Register
address_offset : 0x12 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RMINAR RMINAR read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 MIN1 MIN10 ENB

MIN1 : 1-Minute Count Value for the ones place of minutes
bits : 0 - 2 (3 bit)
access : read-write

MIN10 : 10-Minute Count Value for the tens place of minutes
bits : 4 - 5 (2 bit)
access : read-write

ENB : Compare enable
bits : 7 - 6 (0 bit)
access : read-write

Enumeration:

#0 : 0

The register value is not compared with the RMINCNT counter value.

#1 : 1

The register value is compared with the RMINCNT counter value.

End of enumeration elements list.


BCNT1AR

Binary Counter 1 Alarm Register
address_offset : 0x12 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
alternate_register : RMINAR
reset_Mask : 0x0

BCNT1AR BCNT1AR read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 BCNT1AR

BCNT1AR : he BCNT1AR counter is a readable/writable alarm register corresponding to 32-bit binary counter b15 to b8.
bits : 0 - 6 (7 bit)
access : read-write


CP[2]-CP[1]-CP[0]-RSEC

Second Capture Register
address_offset : 0x122 Bytes (0x0)
size : 8 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0

CP[2]-CP[1]-CP[0]-RSEC CP[2]-CP[1]-CP[0]-RSEC read-only 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 SEC1 SEC10

SEC1 : 1-Second Capture Capture value for the ones place of seconds
bits : 0 - 2 (3 bit)
access : read-only

SEC10 : 10-Second Capture Capture value for the tens place of seconds
bits : 4 - 5 (2 bit)
access : read-only


CP[2]-CP[1]-CP[0]-BCNT0

BCNT0 Capture Register
address_offset : 0x122 Bytes (0x0)
size : 8 bit
access : read-only
reset_value : 0x0
alternate_register : RSEC
reset_Mask : 0x0

CP[2]-CP[1]-CP[0]-BCNT0 CP[2]-CP[1]-CP[0]-BCNT0 read-only 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 BCNT0CP

BCNT0CP : BCNT0CP is a read-only register that captures the BCNT0 value when a time capture event is detected.
bits : 0 - 6 (7 bit)
access : read-only


CP[2]-CP[1]-CP[0]-RMIN

Minute Capture Register
address_offset : 0x124 Bytes (0x0)
size : 8 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0

CP[2]-CP[1]-CP[0]-RMIN CP[2]-CP[1]-CP[0]-RMIN read-only 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 MIN1 MIN10

MIN1 : 1-Minute Capture Capture value for the ones place of minutes
bits : 0 - 2 (3 bit)
access : read-only

MIN10 : 10-Minute Capture Capture value for the tens place of minutes
bits : 4 - 5 (2 bit)
access : read-only


CP[2]-CP[1]-CP[0]-BCNT1

BCNT1 Capture Register
address_offset : 0x124 Bytes (0x0)
size : 8 bit
access : read-only
reset_value : 0x0
alternate_register : RMIN
reset_Mask : 0x0

CP[2]-CP[1]-CP[0]-BCNT1 CP[2]-CP[1]-CP[0]-BCNT1 read-only 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 BCNT1CP

BCNT1CP : BCNT1CP is a read-only register that captures the BCNT1 value when a time capture event is detected.
bits : 0 - 6 (7 bit)
access : read-only


CP[2]-CP[1]-CP[0]-RHR

Hour Capture Register
address_offset : 0x126 Bytes (0x0)
size : 8 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0

CP[2]-CP[1]-CP[0]-RHR CP[2]-CP[1]-CP[0]-RHR read-only 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 HR1 HR10 PM

HR1 : 1-Minute Capture Capture value for the ones place of minutes
bits : 0 - 2 (3 bit)
access : read-only

HR10 : 10-Minute Capture Capture value for the tens place of minutes
bits : 4 - 4 (1 bit)
access : read-only

PM : A.m./p.m. select for time counter setting.
bits : 6 - 5 (0 bit)
access : read-only

Enumeration:

#0 : 0

a.m.

#1 : 1

p.m.

End of enumeration elements list.


CP[2]-CP[1]-CP[0]-BCNT2

BCNT2 Capture Register
address_offset : 0x126 Bytes (0x0)
size : 8 bit
access : read-only
reset_value : 0x0
alternate_register : RHR
reset_Mask : 0x0

CP[2]-CP[1]-CP[0]-BCNT2 CP[2]-CP[1]-CP[0]-BCNT2 read-only 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 BCNT2CP

BCNT2CP : BCNT2CP is a read-only register that captures the BCNT2 value when a time capture event is detected.
bits : 0 - 6 (7 bit)
access : read-only


CP[2]-CP[1]-CP[0]-RDAY

Date Capture Register
address_offset : 0x12A Bytes (0x0)
size : 8 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0

CP[2]-CP[1]-CP[0]-RDAY CP[2]-CP[1]-CP[0]-RDAY read-only 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 DATE1 DATE10

DATE1 : 1-Day Capture Capture value for the ones place of minutes
bits : 0 - 2 (3 bit)
access : read-only

DATE10 : 10-Day Capture Capture value for the tens place of minutes
bits : 4 - 4 (1 bit)
access : read-only


CP[2]-CP[1]-CP[0]-BCNT3

BCNT3 Capture Register
address_offset : 0x12A Bytes (0x0)
size : 8 bit
access : read-only
reset_value : 0x0
alternate_register : RDAY
reset_Mask : 0x0

CP[2]-CP[1]-CP[0]-BCNT3 CP[2]-CP[1]-CP[0]-BCNT3 read-only 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 BCNT3CP

BCNT3CP : BCNT3CP is a read-only register that captures the BCNT3 value when a time capture event is detected.
bits : 0 - 6 (7 bit)
access : read-only


CP[2]-CP[1]-CP[0]-RMON

Month Capture Register
address_offset : 0x12C Bytes (0x0)
size : 8 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0

CP[2]-CP[1]-CP[0]-RMON CP[2]-CP[1]-CP[0]-RMON read-only 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 MON1 MON10

MON1 : 1-Month Capture Capture value for the ones place of months
bits : 0 - 2 (3 bit)
access : read-only

MON10 : 10-Month Capture Capture value for the tens place of months
bits : 4 - 3 (0 bit)
access : read-only


RHRAR

Hour Alarm Register
address_offset : 0x14 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RHRAR RHRAR read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 HR1 HR10 PM ENB

HR1 : 1-Hour Count Value for the ones place of hours
bits : 0 - 2 (3 bit)
access : read-write

HR10 : 10-Hour Count Value for the tens place of hours
bits : 4 - 4 (1 bit)
access : read-write

PM : Time Counter Setting for a.m./p.m.
bits : 6 - 5 (0 bit)
access : read-write

Enumeration:

#0 : 0

a.m.

#1 : 1

p.m.

End of enumeration elements list.

ENB : Compare enable
bits : 7 - 6 (0 bit)
access : read-write

Enumeration:

#0 : 0

The register value is not compared with the RHRCNT counter value.

#1 : 1

The register value is compared with the RHRCNT counter value.

End of enumeration elements list.


BCNT2AR

Binary Counter 2 Alarm Register
address_offset : 0x14 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
alternate_register : RHRAR
reset_Mask : 0x0

BCNT2AR BCNT2AR read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 BCNT2AR

BCNT2AR : The BCNT2AR counter is a readable/writable 32-bit binary counter b23 to b16.
bits : 0 - 6 (7 bit)
access : read-write


RWKAR

Day-of-Week Alarm Register
address_offset : 0x16 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RWKAR RWKAR read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 DAYW ENB

DAYW : Day-of-Week Counting
bits : 0 - 1 (2 bit)
access : read-write

Enumeration:

#000 : 000

Sunday

#001 : 001

Monday

#010 : 010

Tuesday

#011 : 011

Wednesday

#100 : 100

Thursday

#101 : 101

Friday

#110 : 110

Saturday

#111 : 111

Setting Prohibited

End of enumeration elements list.

ENB : Compare enable
bits : 7 - 6 (0 bit)
access : read-write

Enumeration:

#0 : 0

The register value is not compared with the RWKCNT counter value.

#1 : 1

The register value is compared with the RWKCNT counter value.

End of enumeration elements list.


BCNT3AR

Binary Counter 3 Alarm Register
address_offset : 0x16 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
alternate_register : RWKAR
reset_Mask : 0x0

BCNT3AR BCNT3AR read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 BCNT3AR

BCNT3AR : The BCNT3AR counter is a readable/writable 32-bit binary counter b31 to b24.
bits : 0 - 6 (7 bit)
access : read-write


RDAYAR

Date Alarm Register
address_offset : 0x18 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RDAYAR RDAYAR read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 DATE1 DATE10 ENB

DATE1 : 1 Day Value for the ones place of days
bits : 0 - 2 (3 bit)
access : read-write

DATE10 : 10 Days Value for the tens place of days
bits : 4 - 4 (1 bit)
access : read-write

ENB : Compare enable
bits : 7 - 6 (0 bit)
access : read-write

Enumeration:

#0 : 0

The register value is not compared with the RDAYCNT counter value.

#1 : 1

The register value is compared with the RDAYCNT counter value.

End of enumeration elements list.


BCNT0AER

Binary Counter 0 Alarm Enable Register
address_offset : 0x18 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
alternate_register : RDAYAR
reset_Mask : 0x0

BCNT0AER BCNT0AER read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 ENB

ENB : The BCNT0AER register is a readable/writable register for setting the alarm enable corresponding to 32-bit binary counter b7 to b0.
bits : 0 - 6 (7 bit)
access : read-write


RMONAR

Month Alarm Register
address_offset : 0x1A Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RMONAR RMONAR read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 MON1 MON10 ENB

MON1 : 1 Month Value for the ones place of months
bits : 0 - 2 (3 bit)
access : read-write

MON10 : 10 Months Value for the tens place of months
bits : 4 - 3 (0 bit)
access : read-write

ENB : Compare enable
bits : 7 - 6 (0 bit)
access : read-write

Enumeration:

#0 : 0

The register value is not compared with the RMONCNT counter value.

#1 : 1

The register value is compared with the RMONCNT counter value.

End of enumeration elements list.


BCNT1AER

Binary Counter 1 Alarm Enable Register
address_offset : 0x1A Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
alternate_register : RMONAR
reset_Mask : 0x0

BCNT1AER BCNT1AER read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 ENB

ENB : The BCNT1AER register is a readable/writable register for setting the alarm enable corresponding to 32-bit binary counter b15 to b8.
bits : 0 - 6 (7 bit)
access : read-write


RYRAR

Year Alarm Register
address_offset : 0x1C Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RYRAR RYRAR read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 YR1 YR10

YR1 : 1 Year Value for the ones place of years
bits : 0 - 2 (3 bit)
access : read-write

YR10 : 10 Years Value for the tens place of years
bits : 4 - 6 (3 bit)
access : read-write


BCNT2AER

Binary Counter 2 Alarm Enable Register
address_offset : 0x1C Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
alternate_register : RYRAR
reset_Mask : 0x0

BCNT2AER BCNT2AER read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ENB

ENB : The BCNT2AER register is a readable/writable register for setting the alarm enable corresponding to 32-bit binary counter b23 to b16.
bits : 0 - 6 (7 bit)
access : read-write


RYRAREN

Year Alarm Enable Register
address_offset : 0x1E Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RYRAREN RYRAREN read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 ENB

ENB : Compare enable
bits : 7 - 6 (0 bit)
access : read-write

Enumeration:

#0 : 0

The register value is not compared with the RYRCNT counter value.

#1 : 1

The register value is compared with the RYRCNT counter value.

End of enumeration elements list.


BCNT3AER

Binary Counter 3 Alarm Enable Register
address_offset : 0x1E Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
alternate_register : RYRAREN
reset_Mask : 0x0

BCNT3AER BCNT3AER read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 ENB

ENB : The BCNT3AER register is a readable/writable register for setting the alarm enable corresponding to 32-bit binary counter b31 to b24.
bits : 0 - 6 (7 bit)
access : read-write


RSECCNT

Second Counter
address_offset : 0x2 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RSECCNT RSECCNT read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 SEC1 SEC10

SEC1 : 1-Second Count Counts from 0 to 9 every second. When a carry is generated, 1 is added to the tens place.
bits : 0 - 2 (3 bit)
access : read-write

SEC10 : 10-Second Count Counts from 0 to 5 for 60-second counting.
bits : 4 - 5 (2 bit)
access : read-write


BCNT0

Binary Counter 0
address_offset : 0x2 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
alternate_register : RSECCNT
reset_Mask : 0x0

BCNT0 BCNT0 read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 BCNT0

BCNT0 : The BCNT0 counter is a readable/writable 32-bit binary counter b7 to b0.
bits : 0 - 6 (7 bit)
access : read-write


RCR1

RTC Control Register 1
address_offset : 0x22 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RCR1 RCR1 read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 AIE CIE PIE RTCOS PES

AIE : Alarm Interrupt Enable
bits : 0 - -1 (0 bit)
access : read-write

Enumeration:

#0 : 0

An alarm interrupt request is disabled.

#1 : 1

An alarm interrupt request is enabled.

End of enumeration elements list.

CIE : Carry Interrupt Enable
bits : 1 - 0 (0 bit)
access : read-write

Enumeration:

#0 : 0

A carry interrupt request is disabled.

#1 : 1

A carry interrupt request is enabled.

End of enumeration elements list.

PIE : Periodic Interrupt Enable
bits : 2 - 1 (0 bit)
access : read-write

Enumeration:

#0 : 0

A periodic interrupt request is disabled.

#1 : 1

A periodic interrupt request is enabled.

End of enumeration elements list.

RTCOS : RTCOUT Output Select
bits : 3 - 2 (0 bit)
access : read-write

Enumeration:

#0 : 0

RTCOUT outputs 1 Hz.

#1 : 1

RTCOUT outputs 64 Hz.

End of enumeration elements list.

PES : Periodic Interrupt Select
bits : 4 - 6 (3 bit)
access : read-write

Enumeration:

#0110 : 0110

A periodic interrupt is generated every 1/256 second((RCR4.RCKSEL = 0)./A periodic interrupt is generated every 1/128 second((RCR4.RCKSEL = 1).

#0111 : 0111

A periodic interrupt is generated every 1/128 second.

#1000 : 1000

A periodic interrupt is generated every 1/64 second.

#1001 : 1001

A periodic interrupt is generated every 1/32 second.

#1010 : 1010

A periodic interrupt is generated every 1/16 second.

#1011 : 1011

A periodic interrupt is generated every 1/8 second.

#1100 : 1100

A periodic interrupt is generated every 1/4 second.

#1101 : 1101

A periodic interrupt is generated every 1/2 second.

#1110 : 1110

A periodic interrupt is generated every 1 second.

#1111 : 1111

A periodic interrupt is generated every 2 seconds.

End of enumeration elements list.


RCR2

RTC Control Register 2
address_offset : 0x24 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RCR2 RCR2 read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 START RESET ADJ30 RTCOE AADJE AADJP HR24 CNTMD

START : Start
bits : 0 - -1 (0 bit)
access : read-write

Enumeration:

#0 : 0

Prescaler and time counter are stopped.

#1 : 1

Prescaler and time counter operate normally.

End of enumeration elements list.

RESET : RTC Software Reset
bits : 1 - 0 (0 bit)
access : read-write

Enumeration:

#0 : 0

Writing is invalid.(write) / In normal time operation, or an RTC software reset has completed.(read)

#1 : 1

The prescaler and the target registers for RTC software reset *1 are initialized.(write) / During an RTC software reset.(read)

End of enumeration elements list.

ADJ30 : 30-Second Adjustment
bits : 2 - 1 (0 bit)
access : read-write

Enumeration:

#0 : 0

Writing is invalid.(write) / In normal time operation, or 30-second adjustment has completed.(read)

#1 : 1

30-second adjustment is executed.(write) / During 30-second adjustment.(read)

End of enumeration elements list.

RTCOE : RTCOUT Output Enable
bits : 3 - 2 (0 bit)
access : read-write

Enumeration:

#0 : 0

RTCOUT output disabled.

#1 : 1

RTCOUT output enabled.

End of enumeration elements list.

AADJE : Automatic Adjustment Enable (When the LOCO clock is selected, the setting of this bit is disabled.)
bits : 4 - 3 (0 bit)
access : read-write

Enumeration:

#0 : 0

Automatic adjustment is disabled.

#1 : 1

Automatic adjustment is enabled.

End of enumeration elements list.

AADJP : Automatic Adjustment Period Select (When the LOCO clock is selected, the setting of this bit is disabled.)
bits : 5 - 4 (0 bit)
access : read-write

Enumeration:

#0 : 0

The RADJ.ADJ[5:0] setting value is adjusted from the count value of the prescaler every minute.

#1 : 1

The RADJ.ADJ[5:0] setting value is adjusted from the count value of the prescaler every 10 seconds.

End of enumeration elements list.

HR24 : Hours Mode
bits : 6 - 5 (0 bit)
access : read-write

Enumeration:

#0 : 0

The RTC operates in 12-hour mode.

#1 : 1

The RTC operates in 24-hour mode.

End of enumeration elements list.

CNTMD : Count Mode Select
bits : 7 - 6 (0 bit)
access : read-write

Enumeration:

#0 : 0

The calendar count mode.

#1 : 1

The binary count mode.

End of enumeration elements list.


RCR4

RTC Control Register 4
address_offset : 0x28 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RCR4 RCR4 read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 RCKSEL ROPSEL

RCKSEL : Count Source Select
bits : 0 - -1 (0 bit)
access : read-write

Enumeration:

#0 : 0

Sub-clock oscillator is selected.

#1 : 1

LOCO clock oscillator is selected.

End of enumeration elements list.

ROPSEL : RTC Operation Mode Select
bits : 7 - 6 (0 bit)
access : read-write

Enumeration:

#0 : 0

Normal operation mode is selected.

#1 : 1

Low-consumption clock mode is selected.

End of enumeration elements list.


RFRH

Frequency Register H
address_offset : 0x2A Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RFRH RFRH read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 RFC16

RFC16 : Frequency Comparison Value (b16) To generate the operating clock from the LOCOclock, this bit sets the comparison value of the 128-Hz clock cycle.
bits : 0 - -1 (0 bit)
access : read-write


RFRL

Frequency Register L
address_offset : 0x2C Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RFRL RFRL read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 RFC

RFC : Frequency Comparison Value(b15-b0) To generate the operating clock from the main clock, this bit sets the comparison value of the 128-Hz clock cycle.
bits : 0 - 14 (15 bit)
access : read-write


RADJ

Time Error Adjustment Register
address_offset : 0x2E Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RADJ RADJ read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 ADJ PMADJ

ADJ : Adjustment Value These bits specify the adjustment value from the prescaler.
bits : 0 - 4 (5 bit)
access : read-write

PMADJ : Plus-Minus
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

#00 : 00

Adjustment is not performed.

#01 : 01

Adjustment is performed by the addition to the prescaler.

#10 : 10

Adjustment is performed by the subtraction from the prescaler.

#11 : 11

Setting prohibited

End of enumeration elements list.


RMINCNT

Minute Counter
address_offset : 0x4 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RMINCNT RMINCNT read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 MIN1 MIN10

MIN1 : 1-Minute Count Counts from 0 to 9 every minute. When a carry is generated, 1 is added to the tens place.
bits : 0 - 2 (3 bit)
access : read-write

MIN10 : 10-Minute Count Counts from 0 to 5 for 60-minute counting.
bits : 4 - 5 (2 bit)
access : read-write


BCNT1

Binary Counter 1
address_offset : 0x4 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
alternate_register : RMINCNT
reset_Mask : 0x0

BCNT1 BCNT1 read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 BCNT1

BCNT1 : The BCNT1 counter is a readable/writable 32-bit binary counter b15 to b8.
bits : 0 - 6 (7 bit)
access : read-write


RTCCR[0]-RTCCR

Time Capture Control Register
address_offset : 0x40 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RTCCR[0]-RTCCR RTCCR[0]-RTCCR read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 TCCT TCST TCNF

TCCT : Time Capture Control
bits : 0 - 0 (1 bit)
access : read-write

Enumeration:

#00 : 00

No event is detected.

#01 : 01

Rising edge is detected.

#10 : 10

Falling edge is detected.

#11 : 11

Both edges are detected.

End of enumeration elements list.

TCST : Time Capture Status
bits : 2 - 1 (0 bit)
access : read-only

Enumeration:

#0 : 0

No event is detected.

#1 : 1

An event is detected.

End of enumeration elements list.

TCNF : Time Capture Noise Filter Control
bits : 4 - 4 (1 bit)
access : read-write

Enumeration:

#00 : 00

The noise filter is off.

#01 : 01

Setting prohibited

#10 : 10

The noise filter is on (count source).

#11 : 11

The noise filter is on (count source by divided by 32).

End of enumeration elements list.


CP[0]-RSEC

Second Capture Register
address_offset : 0x52 Bytes (0x0)
size : 8 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0

CP[0]-RSEC CP[0]-RSEC read-only 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 SEC1 SEC10

SEC1 : 1-Second Capture Capture value for the ones place of seconds
bits : 0 - 2 (3 bit)
access : read-only

SEC10 : 10-Second Capture Capture value for the tens place of seconds
bits : 4 - 5 (2 bit)
access : read-only


CP[0]-BCNT0

BCNT0 Capture Register
address_offset : 0x52 Bytes (0x0)
size : 8 bit
access : read-only
reset_value : 0x0
alternate_register : RSEC
reset_Mask : 0x0

CP[0]-BCNT0 CP[0]-BCNT0 read-only 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 BCNT0CP

BCNT0CP : BCNT0CP is a read-only register that captures the BCNT0 value when a time capture event is detected.
bits : 0 - 6 (7 bit)
access : read-only


CP[0]-RMIN

Minute Capture Register
address_offset : 0x54 Bytes (0x0)
size : 8 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0

CP[0]-RMIN CP[0]-RMIN read-only 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 MIN1 MIN10

MIN1 : 1-Minute Capture Capture value for the ones place of minutes
bits : 0 - 2 (3 bit)
access : read-only

MIN10 : 10-Minute Capture Capture value for the tens place of minutes
bits : 4 - 5 (2 bit)
access : read-only


CP[0]-BCNT1

BCNT1 Capture Register
address_offset : 0x54 Bytes (0x0)
size : 8 bit
access : read-only
reset_value : 0x0
alternate_register : RMIN
reset_Mask : 0x0

CP[0]-BCNT1 CP[0]-BCNT1 read-only 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 BCNT1CP

BCNT1CP : BCNT1CP is a read-only register that captures the BCNT1 value when a time capture event is detected.
bits : 0 - 6 (7 bit)
access : read-only


CP[0]-RHR

Hour Capture Register
address_offset : 0x56 Bytes (0x0)
size : 8 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0

CP[0]-RHR CP[0]-RHR read-only 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 HR1 HR10 PM

HR1 : 1-Minute Capture Capture value for the ones place of minutes
bits : 0 - 2 (3 bit)
access : read-only

HR10 : 10-Minute Capture Capture value for the tens place of minutes
bits : 4 - 4 (1 bit)
access : read-only

PM : A.m./p.m. select for time counter setting.
bits : 6 - 5 (0 bit)
access : read-only

Enumeration:

#0 : 0

a.m.

#1 : 1

p.m.

End of enumeration elements list.


CP[0]-BCNT2

BCNT2 Capture Register
address_offset : 0x56 Bytes (0x0)
size : 8 bit
access : read-only
reset_value : 0x0
alternate_register : RHR
reset_Mask : 0x0

CP[0]-BCNT2 CP[0]-BCNT2 read-only 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 BCNT2CP

BCNT2CP : BCNT2CP is a read-only register that captures the BCNT2 value when a time capture event is detected.
bits : 0 - 6 (7 bit)
access : read-only


CP[0]-RDAY

Date Capture Register
address_offset : 0x5A Bytes (0x0)
size : 8 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0

CP[0]-RDAY CP[0]-RDAY read-only 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 DATE1 DATE10

DATE1 : 1-Day Capture Capture value for the ones place of minutes
bits : 0 - 2 (3 bit)
access : read-only

DATE10 : 10-Day Capture Capture value for the tens place of minutes
bits : 4 - 4 (1 bit)
access : read-only


CP[0]-BCNT3

BCNT3 Capture Register
address_offset : 0x5A Bytes (0x0)
size : 8 bit
access : read-only
reset_value : 0x0
alternate_register : RDAY
reset_Mask : 0x0

CP[0]-BCNT3 CP[0]-BCNT3 read-only 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 BCNT3CP

BCNT3CP : BCNT3CP is a read-only register that captures the BCNT3 value when a time capture event is detected.
bits : 0 - 6 (7 bit)
access : read-only


CP[0]-RMON

Month Capture Register
address_offset : 0x5C Bytes (0x0)
size : 8 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0

CP[0]-RMON CP[0]-RMON read-only 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 MON1 MON10

MON1 : 1-Month Capture Capture value for the ones place of months
bits : 0 - 2 (3 bit)
access : read-only

MON10 : 10-Month Capture Capture value for the tens place of months
bits : 4 - 3 (0 bit)
access : read-only


RHRCNT

Hour Counter
address_offset : 0x6 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RHRCNT RHRCNT read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 HR1 HR10 PM

HR1 : 1-Hour Count Counts from 0 to 9 once per hour. When a carry is generated, 1 is added to the tens place.
bits : 0 - 2 (3 bit)
access : read-write

HR10 : 10-Hour Count Counts from 0 to 2 once per carry from the ones place.
bits : 4 - 4 (1 bit)
access : read-write

PM : Time Counter Setting for a.m./p.m.
bits : 6 - 5 (0 bit)
access : read-write

Enumeration:

#0 : 0

a.m.

#1 : 1

p.m.

End of enumeration elements list.


BCNT2

Binary Counter 2
address_offset : 0x6 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
alternate_register : RHRCNT
reset_Mask : 0x0

BCNT2 BCNT2 read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 BCNT2

BCNT2 : The BCNT2 counter is a readable/writable 32-bit binary counter b23 to b16.
bits : 0 - 6 (7 bit)
access : read-write


RWKCNT

Day-of-Week Counter
address_offset : 0x8 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RWKCNT RWKCNT read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 DAYW

DAYW : Day-of-Week Counting
bits : 0 - 1 (2 bit)
access : read-write

Enumeration:

#000 : 000

Sunday

#001 : 001

Monday

#010 : 010

Tuesday

#011 : 011

Wednesday

#100 : 100

Thursday

#101 : 101

Friday

#110 : 110

Saturday

#111 : 111

Setting Prohibited

End of enumeration elements list.


BCNT3

Binary Counter 3
address_offset : 0x8 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
alternate_register : RWKCNT
reset_Mask : 0x0

BCNT3 BCNT3 read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 BCNT3

BCNT3 : The BCNT3 counter is a readable/writable 32-bit binary counter b31 to b24.
bits : 0 - 6 (7 bit)
access : read-write


RTCCR[1]-RTCCR[0]-RTCCR

Time Capture Control Register
address_offset : 0x82 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RTCCR[1]-RTCCR[0]-RTCCR RTCCR[1]-RTCCR[0]-RTCCR read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 TCCT TCST TCNF

TCCT : Time Capture Control
bits : 0 - 0 (1 bit)
access : read-write

Enumeration:

#00 : 00

No event is detected.

#01 : 01

Rising edge is detected.

#10 : 10

Falling edge is detected.

#11 : 11

Both edges are detected.

End of enumeration elements list.

TCST : Time Capture Status
bits : 2 - 1 (0 bit)
access : read-only

Enumeration:

#0 : 0

No event is detected.

#1 : 1

An event is detected.

End of enumeration elements list.

TCNF : Time Capture Noise Filter Control
bits : 4 - 4 (1 bit)
access : read-write

Enumeration:

#00 : 00

The noise filter is off.

#01 : 01

Setting prohibited

#10 : 10

The noise filter is on (count source).

#11 : 11

The noise filter is on (count source by divided by 32).

End of enumeration elements list.


RDAYCNT

Day Counter
address_offset : 0xA Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RDAYCNT RDAYCNT read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 DATE1 DATE10

DATE1 : 1-Day Count Counts from 0 to 9 once per day. When a carry is generated, 1 is added to the tens place.
bits : 0 - 2 (3 bit)
access : read-write

DATE10 : 10-Day Count Counts from 0 to 3 once per carry from the ones place.
bits : 4 - 4 (1 bit)
access : read-write


CP[1]-CP[0]-RSEC

Second Capture Register
address_offset : 0xB2 Bytes (0x0)
size : 8 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0

CP[1]-CP[0]-RSEC CP[1]-CP[0]-RSEC read-only 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 SEC1 SEC10

SEC1 : 1-Second Capture Capture value for the ones place of seconds
bits : 0 - 2 (3 bit)
access : read-only

SEC10 : 10-Second Capture Capture value for the tens place of seconds
bits : 4 - 5 (2 bit)
access : read-only


CP[1]-CP[0]-BCNT0

BCNT0 Capture Register
address_offset : 0xB2 Bytes (0x0)
size : 8 bit
access : read-only
reset_value : 0x0
alternate_register : RSEC
reset_Mask : 0x0

CP[1]-CP[0]-BCNT0 CP[1]-CP[0]-BCNT0 read-only 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 BCNT0CP

BCNT0CP : BCNT0CP is a read-only register that captures the BCNT0 value when a time capture event is detected.
bits : 0 - 6 (7 bit)
access : read-only


CP[1]-CP[0]-RMIN

Minute Capture Register
address_offset : 0xB4 Bytes (0x0)
size : 8 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0

CP[1]-CP[0]-RMIN CP[1]-CP[0]-RMIN read-only 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 MIN1 MIN10

MIN1 : 1-Minute Capture Capture value for the ones place of minutes
bits : 0 - 2 (3 bit)
access : read-only

MIN10 : 10-Minute Capture Capture value for the tens place of minutes
bits : 4 - 5 (2 bit)
access : read-only


CP[1]-CP[0]-BCNT1

BCNT1 Capture Register
address_offset : 0xB4 Bytes (0x0)
size : 8 bit
access : read-only
reset_value : 0x0
alternate_register : RMIN
reset_Mask : 0x0

CP[1]-CP[0]-BCNT1 CP[1]-CP[0]-BCNT1 read-only 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 BCNT1CP

BCNT1CP : BCNT1CP is a read-only register that captures the BCNT1 value when a time capture event is detected.
bits : 0 - 6 (7 bit)
access : read-only


CP[1]-CP[0]-RHR

Hour Capture Register
address_offset : 0xB6 Bytes (0x0)
size : 8 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0

CP[1]-CP[0]-RHR CP[1]-CP[0]-RHR read-only 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 HR1 HR10 PM

HR1 : 1-Minute Capture Capture value for the ones place of minutes
bits : 0 - 2 (3 bit)
access : read-only

HR10 : 10-Minute Capture Capture value for the tens place of minutes
bits : 4 - 4 (1 bit)
access : read-only

PM : A.m./p.m. select for time counter setting.
bits : 6 - 5 (0 bit)
access : read-only

Enumeration:

#0 : 0

a.m.

#1 : 1

p.m.

End of enumeration elements list.


CP[1]-CP[0]-BCNT2

BCNT2 Capture Register
address_offset : 0xB6 Bytes (0x0)
size : 8 bit
access : read-only
reset_value : 0x0
alternate_register : RHR
reset_Mask : 0x0

CP[1]-CP[0]-BCNT2 CP[1]-CP[0]-BCNT2 read-only 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 BCNT2CP

BCNT2CP : BCNT2CP is a read-only register that captures the BCNT2 value when a time capture event is detected.
bits : 0 - 6 (7 bit)
access : read-only


CP[1]-CP[0]-RDAY

Date Capture Register
address_offset : 0xBA Bytes (0x0)
size : 8 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0

CP[1]-CP[0]-RDAY CP[1]-CP[0]-RDAY read-only 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 DATE1 DATE10

DATE1 : 1-Day Capture Capture value for the ones place of minutes
bits : 0 - 2 (3 bit)
access : read-only

DATE10 : 10-Day Capture Capture value for the tens place of minutes
bits : 4 - 4 (1 bit)
access : read-only


CP[1]-CP[0]-BCNT3

BCNT3 Capture Register
address_offset : 0xBA Bytes (0x0)
size : 8 bit
access : read-only
reset_value : 0x0
alternate_register : RDAY
reset_Mask : 0x0

CP[1]-CP[0]-BCNT3 CP[1]-CP[0]-BCNT3 read-only 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 BCNT3CP

BCNT3CP : BCNT3CP is a read-only register that captures the BCNT3 value when a time capture event is detected.
bits : 0 - 6 (7 bit)
access : read-only


CP[1]-CP[0]-RMON

Month Capture Register
address_offset : 0xBC Bytes (0x0)
size : 8 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0

CP[1]-CP[0]-RMON CP[1]-CP[0]-RMON read-only 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 MON1 MON10

MON1 : 1-Month Capture Capture value for the ones place of months
bits : 0 - 2 (3 bit)
access : read-only

MON10 : 10-Month Capture Capture value for the tens place of months
bits : 4 - 3 (0 bit)
access : read-only


RMONCNT

Month Counter
address_offset : 0xC Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RMONCNT RMONCNT read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 MON1 MON10

MON1 : 1-Month Count Counts from 0 to 9 once per month. When a carry is generated, 1 is added to the tens place.
bits : 0 - 2 (3 bit)
access : read-write

MON10 : 10-Month Count Counts from 0 to 1 once per carry from the ones place.
bits : 4 - 3 (0 bit)
access : read-write


RTCCR[2]-RTCCR[1]-RTCCR[0]-RTCCR

Time Capture Control Register
address_offset : 0xC6 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RTCCR[2]-RTCCR[1]-RTCCR[0]-RTCCR RTCCR[2]-RTCCR[1]-RTCCR[0]-RTCCR read-write 0 1 2 3 4 5 6 7 Resets to 0 0 0 0 0 0 0 0 TCCT TCST TCNF

TCCT : Time Capture Control
bits : 0 - 0 (1 bit)
access : read-write

Enumeration:

#00 : 00

No event is detected.

#01 : 01

Rising edge is detected.

#10 : 10

Falling edge is detected.

#11 : 11

Both edges are detected.

End of enumeration elements list.

TCST : Time Capture Status
bits : 2 - 1 (0 bit)
access : read-only

Enumeration:

#0 : 0

No event is detected.

#1 : 1

An event is detected.

End of enumeration elements list.

TCNF : Time Capture Noise Filter Control
bits : 4 - 4 (1 bit)
access : read-write

Enumeration:

#00 : 00

The noise filter is off.

#01 : 01

Setting prohibited

#10 : 10

The noise filter is on (count source).

#11 : 11

The noise filter is on (count source by divided by 32).

End of enumeration elements list.


RYRCNT

Year Counter
address_offset : 0xE Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

RYRCNT RYRCNT read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 YR1 YR10

YR1 : 1-Year Count Counts from 0 to 9 once per year. When a carry is generated, 1 is added to the tens place.
bits : 0 - 2 (3 bit)
access : read-write

YR10 : 10-Year Count Counts from 0 to 9 once per carry from ones place. When a carry is generated in the tens place, 1 is added to the hundreds place.
bits : 4 - 6 (3 bit)
access : read-write



Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !

This website is sponsored by EmbeetleEmbeetle, an IDE designed from scratch for embedded software developers.