\n

ACMP0

Peripheral Memory Blocks

address_offset : 0x0 Bytes (0x0)
size : 0x400 byte (0x0)
mem_usage : registers
protection : not protected

Registers

CTRL

IFS

IFC

IEN

APORTREQ

APORTCONFLICT

HYSTERESIS0

HYSTERESIS1

INPUTSEL

ROUTEPEN

ROUTELOC0

EXTIFCTRL

STATUS

IF


CTRL

Control Register
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

CTRL CTRL read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 EN INACTVAL GPIOINV APORTXMASTERDIS APORTYMASTERDIS APORTVMASTERDIS PWRSEL ACCURACY INPUTRANGE IRISE IFALL BIASPROG FULLBIAS

EN : Analog Comparator Enable
bits : 0 - 0 (1 bit)
access : read-write

INACTVAL : Inactive Value
bits : 2 - 2 (1 bit)
access : read-write

GPIOINV : Comparator GPIO Output Invert
bits : 3 - 3 (1 bit)
access : read-write

APORTXMASTERDIS : APORT Bus X Master Disable
bits : 8 - 8 (1 bit)
access : read-write

APORTYMASTERDIS : APORT Bus Y Master Disable
bits : 9 - 9 (1 bit)
access : read-write

APORTVMASTERDIS : APORT Bus Master Disable for Bus Selected By VASEL
bits : 10 - 10 (1 bit)
access : read-write

PWRSEL : Power Select
bits : 12 - 14 (3 bit)
access : read-write

Enumeration:

0x00000000 : AVDD

AVDD supply

0x00000001 : DVDD

DVDD supply

0x00000002 : IOVDD0

IOVDD/IOVDD0 supply

0x00000004 : IOVDD1

IOVDD1 supply (if part has two I/O voltages)

End of enumeration elements list.

ACCURACY : ACMP Accuracy Mode
bits : 15 - 15 (1 bit)
access : read-write

INPUTRANGE : Input Range
bits : 18 - 19 (2 bit)
access : read-write

Enumeration:

0x00000000 : FULL

Setting when the input can be from 0 to ACMPVDD.

0x00000001 : GTVDDDIV2

Setting when the input will always be greater than ACMPVDD/2.

0x00000002 : LTVDDDIV2

Setting when the input will always be less than ACMPVDD/2.

End of enumeration elements list.

IRISE : Rising Edge Interrupt Sense
bits : 20 - 20 (1 bit)
access : read-write

IFALL : Falling Edge Interrupt Sense
bits : 21 - 21 (1 bit)
access : read-write

BIASPROG : Bias Configuration
bits : 24 - 29 (6 bit)
access : read-write

FULLBIAS : Full Bias Current
bits : 31 - 31 (1 bit)
access : read-write


IFS

Interrupt Flag Set Register
address_offset : 0x10 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0

IFS IFS write-only 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 EDGE WARMUP APORTCONFLICT

EDGE : Set EDGE Interrupt Flag
bits : 0 - 0 (1 bit)
access : write-only

WARMUP : Set WARMUP Interrupt Flag
bits : 1 - 1 (1 bit)
access : write-only

APORTCONFLICT : Set APORTCONFLICT Interrupt Flag
bits : 2 - 2 (1 bit)
access : write-only


IFC

Interrupt Flag Clear Register
address_offset : 0x14 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0

IFC IFC write-only 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 EDGE WARMUP APORTCONFLICT

EDGE : Clear EDGE Interrupt Flag
bits : 0 - 0 (1 bit)
access : write-only

WARMUP : Clear WARMUP Interrupt Flag
bits : 1 - 1 (1 bit)
access : write-only

APORTCONFLICT : Clear APORTCONFLICT Interrupt Flag
bits : 2 - 2 (1 bit)
access : write-only


IEN

Interrupt Enable Register
address_offset : 0x18 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

IEN IEN read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 EDGE WARMUP APORTCONFLICT

EDGE : EDGE Interrupt Enable
bits : 0 - 0 (1 bit)
access : read-write

WARMUP : WARMUP Interrupt Enable
bits : 1 - 1 (1 bit)
access : read-write

APORTCONFLICT : APORTCONFLICT Interrupt Enable
bits : 2 - 2 (1 bit)
access : read-write


APORTREQ

APORT Request Status Register
address_offset : 0x20 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0

APORTREQ APORTREQ read-only 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 APORT0XREQ APORT0YREQ APORT1XREQ APORT1YREQ APORT2XREQ APORT2YREQ APORT3XREQ APORT3YREQ APORT4XREQ APORT4YREQ

APORT0XREQ : 1 If the Bus Connected to APORT0X is Requested
bits : 0 - 0 (1 bit)
access : read-only

APORT0YREQ : 1 If the Bus Connected to APORT0Y is Requested
bits : 1 - 1 (1 bit)
access : read-only

APORT1XREQ : 1 If the Bus Connected to APORT2X is Requested
bits : 2 - 2 (1 bit)
access : read-only

APORT1YREQ : 1 If the Bus Connected to APORT1X is Requested
bits : 3 - 3 (1 bit)
access : read-only

APORT2XREQ : 1 If the Bus Connected to APORT2X is Requested
bits : 4 - 4 (1 bit)
access : read-only

APORT2YREQ : 1 If the Bus Connected to APORT2Y is Requested
bits : 5 - 5 (1 bit)
access : read-only

APORT3XREQ : 1 If the Bus Connected to APORT3X is Requested
bits : 6 - 6 (1 bit)
access : read-only

APORT3YREQ : 1 If the Bus Connected to APORT3Y is Requested
bits : 7 - 7 (1 bit)
access : read-only

APORT4XREQ : 1 If the Bus Connected to APORT4X is Requested
bits : 8 - 8 (1 bit)
access : read-only

APORT4YREQ : 1 If the Bus Connected to APORT4Y is Requested
bits : 9 - 9 (1 bit)
access : read-only


APORTCONFLICT

APORT Conflict Status Register
address_offset : 0x24 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0

APORTCONFLICT APORTCONFLICT read-only 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 APORT0XCONFLICT APORT0YCONFLICT APORT1XCONFLICT APORT1YCONFLICT APORT2XCONFLICT APORT2YCONFLICT APORT3XCONFLICT APORT3YCONFLICT APORT4XCONFLICT APORT4YCONFLICT

APORT0XCONFLICT : 1 If the Bus Connected to APORT0X is in Conflict With Another Peripheral
bits : 0 - 0 (1 bit)
access : read-only

APORT0YCONFLICT : 1 If the Bus Connected to APORT0Y is in Conflict With Another Peripheral
bits : 1 - 1 (1 bit)
access : read-only

APORT1XCONFLICT : 1 If the Bus Connected to APORT1X is in Conflict With Another Peripheral
bits : 2 - 2 (1 bit)
access : read-only

APORT1YCONFLICT : 1 If the Bus Connected to APORT1X is in Conflict With Another Peripheral
bits : 3 - 3 (1 bit)
access : read-only

APORT2XCONFLICT : 1 If the Bus Connected to APORT2X is in Conflict With Another Peripheral
bits : 4 - 4 (1 bit)
access : read-only

APORT2YCONFLICT : 1 If the Bus Connected to APORT2Y is in Conflict With Another Peripheral
bits : 5 - 5 (1 bit)
access : read-only

APORT3XCONFLICT : 1 If the Bus Connected to APORT3X is in Conflict With Another Peripheral
bits : 6 - 6 (1 bit)
access : read-only

APORT3YCONFLICT : 1 If the Bus Connected to APORT3Y is in Conflict With Another Peripheral
bits : 7 - 7 (1 bit)
access : read-only

APORT4XCONFLICT : 1 If the Bus Connected to APORT4X is in Conflict With Another Peripheral
bits : 8 - 8 (1 bit)
access : read-only

APORT4YCONFLICT : 1 If the Bus Connected to APORT4Y is in Conflict With Another Peripheral
bits : 9 - 9 (1 bit)
access : read-only


HYSTERESIS0

Hysteresis 0 Register
address_offset : 0x28 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

HYSTERESIS0 HYSTERESIS0 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 HYST DIVVA DIVVB

HYST : Hysteresis Select When ACMPOUT=0
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0x00000000 : HYST0

No hysteresis

0x00000001 : HYST1

14 mV hysteresis

0x00000002 : HYST2

25 mV hysteresis

0x00000003 : HYST3

30 mV hysteresis

0x00000004 : HYST4

35 mV hysteresis

0x00000005 : HYST5

39 mV hysteresis

0x00000006 : HYST6

42 mV hysteresis

0x00000007 : HYST7

45 mV hysteresis

0x00000008 : HYST8

No hysteresis

0x00000009 : HYST9

-14 mV hysteresis

0x0000000A : HYST10

-25 mV hysteresis

0x0000000B : HYST11

-30 mV hysteresis

0x0000000C : HYST12

-35 mV hysteresis

0x0000000D : HYST13

-39 mV hysteresis

0x0000000E : HYST14

-42 mV hysteresis

0x0000000F : HYST15

-45 mV hysteresis

End of enumeration elements list.

DIVVA : Divider for VA Voltage When ACMPOUT=0
bits : 16 - 21 (6 bit)
access : read-write

DIVVB : Divider for VB Voltage When ACMPOUT=0
bits : 24 - 29 (6 bit)
access : read-write


HYSTERESIS1

Hysteresis 1 Register
address_offset : 0x2C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

HYSTERESIS1 HYSTERESIS1 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 HYST DIVVA DIVVB

HYST : Hysteresis Select When ACMPOUT=1
bits : 0 - 3 (4 bit)
access : read-write

Enumeration:

0x00000000 : HYST0

No hysteresis

0x00000001 : HYST1

14 mV hysteresis

0x00000002 : HYST2

25 mV hysteresis

0x00000003 : HYST3

30 mV hysteresis

0x00000004 : HYST4

35 mV hysteresis

0x00000005 : HYST5

39 mV hysteresis

0x00000006 : HYST6

42 mV hysteresis

0x00000007 : HYST7

45 mV hysteresis

0x00000008 : HYST8

No hysteresis

0x00000009 : HYST9

-14 mV hysteresis

0x0000000A : HYST10

-25 mV hysteresis

0x0000000B : HYST11

-30 mV hysteresis

0x0000000C : HYST12

-35 mV hysteresis

0x0000000D : HYST13

-39 mV hysteresis

0x0000000E : HYST14

-42 mV hysteresis

0x0000000F : HYST15

-45 mV hysteresis

End of enumeration elements list.

DIVVA : Divider for VA Voltage When ACMPOUT=1
bits : 16 - 21 (6 bit)
access : read-write

DIVVB : Divider for VB Voltage When ACMPOUT=1
bits : 24 - 29 (6 bit)
access : read-write


INPUTSEL

Input Selection Register
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

INPUTSEL INPUTSEL read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 POSSEL NEGSEL VASEL VBSEL VLPSEL CSRESEN CSRESSEL

POSSEL : Positive Input Select
bits : 0 - 7 (8 bit)
access : read-write

NEGSEL : Negative Input Select
bits : 8 - 15 (8 bit)
access : read-write

VASEL : VA Selection
bits : 16 - 21 (6 bit)
access : read-write

Enumeration:

0x00000000 : VDD

ACMPVDD

0x00000001 : APORT2YCH0

APORT2Y Channel 0

0x00000003 : APORT2YCH2

APORT2Y Channel 2

0x00000005 : APORT2YCH4

APORT2Y Channel 4

0x00000007 : APORT2YCH6

APORT2Y Channel 6

0x00000009 : APORT2YCH8

APORT2Y Channel 8

0x0000000B : APORT2YCH10

APORT2Y Channel 10

0x0000000D : APORT2YCH12

APORT2Y Channel 12

0x0000000F : APORT2YCH14

APORT2Y Channel 14

0x00000011 : APORT2YCH16

APORT2Y Channel 16

0x00000013 : APORT2YCH18

APORT2Y Channel 18

0x00000015 : APORT2YCH20

APORT2Y Channel 20

0x00000017 : APORT2YCH22

APORT2Y Channel 22

0x00000019 : APORT2YCH24

APORT2Y Channel 24

0x0000001B : APORT2YCH26

APORT2Y Channel 26

0x0000001D : APORT2YCH28

APORT2Y Channel 28

0x0000001F : APORT2YCH30

APORT2Y Channel 30

0x00000020 : APORT1XCH0

APORT1X Channel 0

0x00000021 : APORT1YCH1

APORT1Y Channel 1

0x00000022 : APORT1XCH2

APORT1X Channel 2

0x00000023 : APORT1YCH3

APORT1Y Channel 3

0x00000024 : APORT1XCH4

APORT1X Channel 4

0x00000025 : APORT1YCH5

APORT1Y Channel 5

0x00000026 : APORT1XCH6

APORT1X Channel 6

0x00000027 : APORT1YCH7

APORT1Y Channel 7

0x00000028 : APORT1XCH8

APORT1X Channel 8

0x00000029 : APORT1YCH9

APORT1Y Channel 9

0x0000002A : APORT1XCH10

APORT1X Channel 10

0x0000002B : APORT1YCH11

APORT1Y Channel 11

0x0000002C : APORT1XCH12

APORT1X Channel 12

0x0000002D : APORT1YCH13

APORT1Y Channel 13

0x0000002E : APORT1XCH14

APORT1X Channel 14

0x0000002F : APORT1YCH15

APORT1Y Channel 15

0x00000030 : APORT1XCH16

APORT1X Channel 16

0x00000031 : APORT1YCH17

APORT1Y Channel 17

0x00000032 : APORT1XCH18

APORT1X Channel 18

0x00000033 : APORT1YCH19

APORT1Y Channel 19

0x00000034 : APORT1XCH20

APORT1X Channel 20

0x00000035 : APORT1YCH21

APORT1Y Channel 21

0x00000036 : APORT1XCH22

APORT1X Channel 22

0x00000037 : APORT1YCH23

APORT1Y Channel 23

0x00000038 : APORT1XCH24

APORT1X Channel 24

0x00000039 : APORT1YCH25

APORT1Y Channel 25

0x0000003A : APORT1XCH26

APORT1X Channel 26

0x0000003B : APORT1YCH27

APORT1Y Channel 27

0x0000003C : APORT1XCH28

APORT1X Channel 28

0x0000003D : APORT1YCH29

APORT1Y Channel 29

0x0000003E : APORT1XCH30

APORT1X Channel 30

0x0000003F : APORT1YCH31

APORT1Y Channel 31

End of enumeration elements list.

VBSEL : VB Selection
bits : 22 - 22 (1 bit)
access : read-write

VLPSEL : Low-Power Sampled Voltage Selection
bits : 24 - 24 (1 bit)
access : read-write

CSRESEN : Capacitive Sense Mode Internal Resistor Enable
bits : 26 - 26 (1 bit)
access : read-write

CSRESSEL : Capacitive Sense Mode Internal Resistor Select
bits : 28 - 30 (3 bit)
access : read-write

Enumeration:

0x00000000 : RES0

Internal capacitive sense resistor value 0

0x00000001 : RES1

Internal capacitive sense resistor value 1

0x00000002 : RES2

Internal capacitive sense resistor value 2

0x00000003 : RES3

Internal capacitive sense resistor value 3

0x00000004 : RES4

Internal capacitive sense resistor value 4

0x00000005 : RES5

Internal capacitive sense resistor value 5

0x00000006 : RES6

Internal capacitive sense resistor value 6

0x00000007 : RES7

Internal capacitive sense resistor value 7

End of enumeration elements list.


ROUTEPEN

I/O Routing Pine Enable Register
address_offset : 0x40 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

ROUTEPEN ROUTEPEN read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 OUTPEN

OUTPEN : ACMP Output Pin Enable
bits : 0 - 0 (1 bit)
access : read-write


ROUTELOC0

I/O Routing Location Register
address_offset : 0x44 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

ROUTELOC0 ROUTELOC0 read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 OUTLOC

OUTLOC : I/O Location
bits : 0 - 5 (6 bit)
access : read-write

Enumeration:

0x00000000 : LOC0

Location 0

0x00000001 : LOC1

Location 1

0x00000002 : LOC2

Location 2

0x00000003 : LOC3

Location 3

0x00000004 : LOC4

Location 4

0x00000005 : LOC5

Location 5

0x00000006 : LOC6

Location 6

0x00000007 : LOC7

Location 7

End of enumeration elements list.


EXTIFCTRL

External Override Interface Control
address_offset : 0x48 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

EXTIFCTRL EXTIFCTRL read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 EN APORTSEL

EN : Enable External Interface
bits : 0 - 0 (1 bit)
access : read-write

APORTSEL : APORT Selection for External Interface
bits : 4 - 7 (4 bit)
access : read-write

Enumeration:

0x00000000 : APORT0X

APORT0X used. EXT_BASE = ACMP_INPUTSEL_POSSEL_APORT0XCH0.

0x00000001 : APORT0Y

APORT0Y used. EXT_BASE = ACMP_INPUTSEL_POSSEL_APORT0YCH0.

0x00000002 : APORT1X

APORT1X used. EXT_BASE = ACMP_INPUTSEL_POSSEL_APORT1XCH0.

0x00000003 : APORT1Y

APORT1Y used. EXT_BASE = ACMP_INPUTSEL_POSSEL_APORT1XCH0.

0x00000004 : APORT1XY

APORT1X/Y used. EXT_BASE = ACMP_INPUTSEL_POSSEL_APORT1XCH0.

0x00000005 : APORT2X

APORT2X used. EXT_BASE = ACMP_INPUTSEL_POSSEL_APORT2YCH0.

0x00000006 : APORT2Y

APORT2Y used. EXT_BASE = ACMP_INPUTSEL_POSSEL_APORT2YCH0.

0x00000007 : APORT2YX

APORT2Y/X used. EXT_BASE = ACMP_INPUTSEL_POSSEL_APORT2YCH0.

0x00000008 : APORT3X

APORT3X used. EXT_BASE = ACMP_INPUTSEL_POSSEL_APORT3XCH0.

0x00000009 : APORT3Y

APORT3Y used. EXT_BASE = ACMP_INPUTSEL_POSSEL_APORT3XCH0.

0x0000000A : APORT3XY

APORT3X/Y used. EXT_BASE = ACMP_INPUTSEL_POSSEL_APORT3XCH0.

0x0000000B : APORT4X

APORT4X used. EXT_BASE = ACMP_INPUTSEL_POSSEL_APORT4YCH0.

0x0000000C : APORT4Y

APORT4Y used. EXT_BASE = ACMP_INPUTSEL_POSSEL_APORT4YCH0.

0x0000000D : APORT4YX

APORT4Y/X used. EXT_BASE = ACMP_INPUTSEL_POSSEL_APORT4YCH0.

End of enumeration elements list.


STATUS

Status Register
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0

STATUS STATUS read-only 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ACMPACT ACMPOUT APORTCONFLICT EXTIFACT

ACMPACT : Analog Comparator Active
bits : 0 - 0 (1 bit)
access : read-only

ACMPOUT : Analog Comparator Output
bits : 1 - 1 (1 bit)
access : read-only

APORTCONFLICT : APORT Conflict Output
bits : 2 - 2 (1 bit)
access : read-only

EXTIFACT : External Override Interface Active
bits : 3 - 3 (1 bit)
access : read-only


IF

Interrupt Flag Register
address_offset : 0xC Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0

IF IF read-only 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 EDGE WARMUP APORTCONFLICT

EDGE : Edge Triggered Interrupt Flag
bits : 0 - 0 (1 bit)
access : read-only

WARMUP : Warm-up Interrupt Flag
bits : 1 - 1 (1 bit)
access : read-only

APORTCONFLICT : APORT Conflict Interrupt Flag
bits : 2 - 2 (1 bit)
access : read-only



Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !

This website is sponsored by EmbeetleEmbeetle, an IDE designed from scratch for embedded software developers.