\n
address_offset : 0x0 Bytes (0x0)
size : 0x400 byte (0x0)
mem_usage : registers
protection : not protected
Control Register
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SCANMODE : Configure Scan Mode
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
0x00000000 : PERIODIC
A new scan is started each time the period counter overflows
0x00000001 : ONESHOT
A single scan is performed when START in CMD is set
0x00000002 : PRS
Pulse on PRS channel
End of enumeration elements list.
PRSSEL : Scan Start PRS Select
bits : 2 - 5 (4 bit)
access : read-write
Enumeration:
0x00000000 : PRSCH0
PRS Channel 0 selected as input
0x00000001 : PRSCH1
PRS Channel 1 selected as input
0x00000002 : PRSCH2
PRS Channel 2 selected as input
0x00000003 : PRSCH3
PRS Channel 3 selected as input
0x00000004 : PRSCH4
PRS Channel 4 selected as input
0x00000005 : PRSCH5
PRS Channel 5 selected as input
0x00000006 : PRSCH6
PRS Channel 6 selected as input
0x00000007 : PRSCH7
PRS Channel 7 selected as input
0x00000008 : PRSCH8
PRS Channel 8 selected as input
0x00000009 : PRSCH9
PRS Channel 9 selected as input
0x0000000A : PRSCH10
PRS Channel 10 selected as input
0x0000000B : PRSCH11
PRS Channel 11 selected as input
0x0000000C : PRSCH12
PRS Channel 12 selected as input
0x0000000D : PRSCH13
PRS Channel 13 selected as input
0x0000000E : PRSCH14
PRS Channel 14 selected as input
0x0000000F : PRSCH15
PRS Channel 15 selected as input
End of enumeration elements list.
SCANCONF : Select Scan Configuration
bits : 7 - 8 (2 bit)
access : read-write
Enumeration:
0x00000000 : DIRMAP
The channel configuration register registers used are directly mapped to the channel number.
0x00000001 : INVMAP
The channel configuration register registers used are CHX+8_CONF for channels 0-7 and CHX-8_CONF for channels 8-15.
0x00000002 : TOGGLE
The channel configuration register registers used toggles between CHX_CONF and CHX+8_CONF when channel x triggers
0x00000003 : DECDEF
The decoder state defines the CONF registers to be used.
End of enumeration elements list.
ALTEXMAP : Alternative Excitation Map
bits : 11 - 11 (1 bit)
access : read-write
DUALSAMPLE : Enable Dual Sample Mode
bits : 13 - 13 (1 bit)
access : read-write
BUFOW : Result Buffer Overwrite
bits : 16 - 16 (1 bit)
access : read-write
STRSCANRES : Enable Storing of SCANRES
bits : 17 - 17 (1 bit)
access : read-write
BUFIDL : Result Buffer Interrupt and DMA Trigger Level
bits : 19 - 19 (1 bit)
access : read-write
DMAWU : DMA Wake-up From EM2
bits : 20 - 21 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
No DMA wake-up from EM2
0x00000001 : BUFDATAV
DMA wake-up from EM2 when data is valid in the result buffer
0x00000002 : BUFLEVEL
DMA wake-up from EM2 when the result buffer is full/half-full depending on BUFIDL configuration
End of enumeration elements list.
DEBUGRUN : Debug Mode Run Enable
bits : 22 - 22 (1 bit)
access : read-write
Bias Control Register
address_offset : 0x10 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BIASMODE : Select Bias Mode
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
0x00000000 : DONTTOUCH
Bias module is controlled by the EMU and is not affected by LESENSE
0x00000001 : DUTYCYCLE
Bias module duty cycled between low power and high accuracy mode
0x00000002 : HIGHACC
Bias module always in high accuracy mode
End of enumeration elements list.
State Transition Configuration a
address_offset : 0x100 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x104 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x108 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x10C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x110 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x114 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x118 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x11C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x120 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x124 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x128 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x12C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x130 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x134 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x138 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x13C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
LESENSE Evaluation Control
address_offset : 0x14 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
WINSIZE : Sliding Window and Step Detection Size
bits : 0 - 15 (16 bit)
access : read-write
State Transition Configuration a
address_offset : 0x140 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x144 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x148 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x14C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x150 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x154 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x158 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x15C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x160 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x164 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x168 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x16C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x170 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x174 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x178 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x17C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
PRS Control Register
address_offset : 0x18 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DECCMPVAL : Decoder State Compare Value
bits : 0 - 4 (5 bit)
access : read-write
DECCMPMASK : Decoder State Compare Value Mask
bits : 8 - 12 (5 bit)
access : read-write
DECCMPEN : Enable PRS Output DECCMP
bits : 16 - 16 (1 bit)
access : read-write
State Transition Configuration a
address_offset : 0x180 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x184 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x188 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x18C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x190 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x194 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x198 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x19C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x1A0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x1A4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x1A8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x1AC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x1B0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x1B4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x1B8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x1BC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
Command Register
address_offset : 0x1C Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
START : Start Scanning of Sensors
bits : 0 - 0 (1 bit)
access : write-only
STOP : Stop Scanning of Sensors
bits : 1 - 1 (1 bit)
access : write-only
DECODE : Start Decoder
bits : 2 - 2 (1 bit)
access : write-only
CLEARBUF : Clear Result Buffer
bits : 3 - 3 (1 bit)
access : write-only
State Transition Configuration a
address_offset : 0x1C0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x1C4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x1C8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x1CC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x1D0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x1D4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x1D8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x1DC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x1E0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x1E4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x1E8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x1EC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x1F0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x1F4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration a
address_offset : 0x1F8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
CHAIN : Enable State Descriptor Chaining
bits : 14 - 14 (1 bit)
access : read-write
SETIF : Set Interrupt Flag Enable
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
State Transition Configuration B
address_offset : 0x1FC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMP : Sensor Compare Value
bits : 0 - 3 (4 bit)
access : read-write
MASK : Sensor Mask
bits : 4 - 7 (4 bit)
access : read-write
NEXTSTATE : Next State Index
bits : 8 - 12 (5 bit)
access : read-write
SETIF : Set Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-write
PRSACT : Configure Transition Action
bits : 16 - 18 (3 bit)
access : read-write
Channel Enable Register
address_offset : 0x20 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CHEN : Enable Scan Channel
bits : 0 - 15 (16 bit)
access : read-write
Scan Results
address_offset : 0x200 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA : Scan Result Buffer
bits : 0 - 15 (16 bit)
access : read-write
DATASRC : Result Data Source
bits : 16 - 19 (4 bit)
access : read-only
Scan Results
address_offset : 0x204 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA : Scan Result Buffer
bits : 0 - 15 (16 bit)
access : read-write
DATASRC : Result Data Source
bits : 16 - 19 (4 bit)
access : read-only
Scan Results
address_offset : 0x208 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA : Scan Result Buffer
bits : 0 - 15 (16 bit)
access : read-write
DATASRC : Result Data Source
bits : 16 - 19 (4 bit)
access : read-only
Scan Results
address_offset : 0x20C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA : Scan Result Buffer
bits : 0 - 15 (16 bit)
access : read-write
DATASRC : Result Data Source
bits : 16 - 19 (4 bit)
access : read-only
Scan Results
address_offset : 0x210 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA : Scan Result Buffer
bits : 0 - 15 (16 bit)
access : read-write
DATASRC : Result Data Source
bits : 16 - 19 (4 bit)
access : read-only
Scan Results
address_offset : 0x214 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA : Scan Result Buffer
bits : 0 - 15 (16 bit)
access : read-write
DATASRC : Result Data Source
bits : 16 - 19 (4 bit)
access : read-only
Scan Results
address_offset : 0x218 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA : Scan Result Buffer
bits : 0 - 15 (16 bit)
access : read-write
DATASRC : Result Data Source
bits : 16 - 19 (4 bit)
access : read-only
Scan Results
address_offset : 0x21C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA : Scan Result Buffer
bits : 0 - 15 (16 bit)
access : read-write
DATASRC : Result Data Source
bits : 16 - 19 (4 bit)
access : read-only
Scan Results
address_offset : 0x220 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA : Scan Result Buffer
bits : 0 - 15 (16 bit)
access : read-write
DATASRC : Result Data Source
bits : 16 - 19 (4 bit)
access : read-only
Scan Results
address_offset : 0x224 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA : Scan Result Buffer
bits : 0 - 15 (16 bit)
access : read-write
DATASRC : Result Data Source
bits : 16 - 19 (4 bit)
access : read-only
Scan Results
address_offset : 0x228 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA : Scan Result Buffer
bits : 0 - 15 (16 bit)
access : read-write
DATASRC : Result Data Source
bits : 16 - 19 (4 bit)
access : read-only
Scan Results
address_offset : 0x22C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA : Scan Result Buffer
bits : 0 - 15 (16 bit)
access : read-write
DATASRC : Result Data Source
bits : 16 - 19 (4 bit)
access : read-only
Scan Results
address_offset : 0x230 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA : Scan Result Buffer
bits : 0 - 15 (16 bit)
access : read-write
DATASRC : Result Data Source
bits : 16 - 19 (4 bit)
access : read-only
Scan Results
address_offset : 0x234 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA : Scan Result Buffer
bits : 0 - 15 (16 bit)
access : read-write
DATASRC : Result Data Source
bits : 16 - 19 (4 bit)
access : read-only
Scan Results
address_offset : 0x238 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA : Scan Result Buffer
bits : 0 - 15 (16 bit)
access : read-write
DATASRC : Result Data Source
bits : 16 - 19 (4 bit)
access : read-only
Scan Results
address_offset : 0x23C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DATA : Scan Result Buffer
bits : 0 - 15 (16 bit)
access : read-write
DATASRC : Result Data Source
bits : 16 - 19 (4 bit)
access : read-only
Scan Result Register
address_offset : 0x24 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SCANRES : Scan Results
bits : 0 - 15 (16 bit)
access : read-write
STEPDIR : Direction of Previous Step Detection
bits : 16 - 31 (16 bit)
access : read-write
Scan Configuration
address_offset : 0x240 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXTIME : Set Excitation Time
bits : 0 - 5 (6 bit)
access : read-write
SAMPLEDLY : Set Sample Delay
bits : 6 - 13 (8 bit)
access : read-write
MEASUREDLY : Set Measure Delay
bits : 14 - 23 (10 bit)
access : read-write
Scan Configuration
address_offset : 0x244 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
THRES : ACMP Threshold or VDAC Data
bits : 0 - 11 (12 bit)
access : read-write
SAMPLE : Select Sample Mode
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
0x00000000 : ACMPCOUNT
Counter output will be used in evaluation
0x00000001 : ACMP
ACMP output will be used in evaluation
0x00000002 : ADC
ADC output will be used in evaluation
0x00000003 : ADCDIFF
Differential ADC output will be used in evaluation
End of enumeration elements list.
SETIF : Enable Interrupt Generation
bits : 14 - 16 (3 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No interrupt is generated
0x00000001 : LEVEL
Set interrupt flag if the sensor triggers.
0x00000002 : POSEDGE
Set interrupt flag on positive edge of the sensor state
0x00000003 : NEGEDGE
Set interrupt flag on negative edge of the sensor state
0x00000004 : BOTHEDGES
Set interrupt flag on both edges of the sensor state
End of enumeration elements list.
EXMODE : Set GPIO Mode
bits : 17 - 18 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Disabled
0x00000001 : HIGH
Push Pull, GPIO is driven high
0x00000002 : LOW
Push Pull, GPIO is driven low
0x00000003 : DACOUT
VDAC output
End of enumeration elements list.
EXCLK : Select Clock Used for Excitation Timing
bits : 19 - 19 (1 bit)
access : read-write
SAMPLECLK : Select Clock Used for Timing of Sample Delay
bits : 20 - 20 (1 bit)
access : read-write
ALTEX : Use Alternative Excite Pin
bits : 21 - 21 (1 bit)
access : read-write
Scan Configuration
address_offset : 0x248 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMPTHRES : Decision Threshold for Sensor Data
bits : 0 - 15 (16 bit)
access : read-write
COMP : Select Mode for Threshold Comparison
bits : 16 - 16 (1 bit)
access : read-write
DECODE : Send Result to Decoder
bits : 17 - 17 (1 bit)
access : read-write
STRSAMPLE : Enable Storing of Sensor Sample in Result Buffer
bits : 18 - 19 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Nothing will be stored in the result buffer.
0x00000001 : DATA
The sensor sample data will be stored in the result buffer.
0x00000002 : DATASRC
The data source (i.e., the channel) will be stored alongside the sensor sample data.
End of enumeration elements list.
SCANRESINV : Enable Inversion of Result
bits : 20 - 20 (1 bit)
access : read-write
MODE : Configure Evaluation Mode
bits : 21 - 22 (2 bit)
access : read-write
Enumeration:
0x00000000 : THRES
Threshold comparison is used to evaluate sensor result
0x00000001 : SLIDINGWIN
Sliding window is used to evaluate sensor result
0x00000002 : STEPDET
Step detection is used to evaluate sensor result
End of enumeration elements list.
Scan Configuration
address_offset : 0x250 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXTIME : Set Excitation Time
bits : 0 - 5 (6 bit)
access : read-write
SAMPLEDLY : Set Sample Delay
bits : 6 - 13 (8 bit)
access : read-write
MEASUREDLY : Set Measure Delay
bits : 14 - 23 (10 bit)
access : read-write
Scan Configuration
address_offset : 0x254 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
THRES : ACMP Threshold or VDAC Data
bits : 0 - 11 (12 bit)
access : read-write
SAMPLE : Select Sample Mode
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
0x00000000 : ACMPCOUNT
Counter output will be used in evaluation
0x00000001 : ACMP
ACMP output will be used in evaluation
0x00000002 : ADC
ADC output will be used in evaluation
0x00000003 : ADCDIFF
Differential ADC output will be used in evaluation
End of enumeration elements list.
SETIF : Enable Interrupt Generation
bits : 14 - 16 (3 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No interrupt is generated
0x00000001 : LEVEL
Set interrupt flag if the sensor triggers.
0x00000002 : POSEDGE
Set interrupt flag on positive edge of the sensor state
0x00000003 : NEGEDGE
Set interrupt flag on negative edge of the sensor state
0x00000004 : BOTHEDGES
Set interrupt flag on both edges of the sensor state
End of enumeration elements list.
EXMODE : Set GPIO Mode
bits : 17 - 18 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Disabled
0x00000001 : HIGH
Push Pull, GPIO is driven high
0x00000002 : LOW
Push Pull, GPIO is driven low
0x00000003 : DACOUT
VDAC output
End of enumeration elements list.
EXCLK : Select Clock Used for Excitation Timing
bits : 19 - 19 (1 bit)
access : read-write
SAMPLECLK : Select Clock Used for Timing of Sample Delay
bits : 20 - 20 (1 bit)
access : read-write
ALTEX : Use Alternative Excite Pin
bits : 21 - 21 (1 bit)
access : read-write
Scan Configuration
address_offset : 0x258 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMPTHRES : Decision Threshold for Sensor Data
bits : 0 - 15 (16 bit)
access : read-write
COMP : Select Mode for Threshold Comparison
bits : 16 - 16 (1 bit)
access : read-write
DECODE : Send Result to Decoder
bits : 17 - 17 (1 bit)
access : read-write
STRSAMPLE : Enable Storing of Sensor Sample in Result Buffer
bits : 18 - 19 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Nothing will be stored in the result buffer.
0x00000001 : DATA
The sensor sample data will be stored in the result buffer.
0x00000002 : DATASRC
The data source (i.e., the channel) will be stored alongside the sensor sample data.
End of enumeration elements list.
SCANRESINV : Enable Inversion of Result
bits : 20 - 20 (1 bit)
access : read-write
MODE : Configure Evaluation Mode
bits : 21 - 22 (2 bit)
access : read-write
Enumeration:
0x00000000 : THRES
Threshold comparison is used to evaluate sensor result
0x00000001 : SLIDINGWIN
Sliding window is used to evaluate sensor result
0x00000002 : STEPDET
Step detection is used to evaluate sensor result
End of enumeration elements list.
Scan Configuration
address_offset : 0x260 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXTIME : Set Excitation Time
bits : 0 - 5 (6 bit)
access : read-write
SAMPLEDLY : Set Sample Delay
bits : 6 - 13 (8 bit)
access : read-write
MEASUREDLY : Set Measure Delay
bits : 14 - 23 (10 bit)
access : read-write
Scan Configuration
address_offset : 0x264 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
THRES : ACMP Threshold or VDAC Data
bits : 0 - 11 (12 bit)
access : read-write
SAMPLE : Select Sample Mode
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
0x00000000 : ACMPCOUNT
Counter output will be used in evaluation
0x00000001 : ACMP
ACMP output will be used in evaluation
0x00000002 : ADC
ADC output will be used in evaluation
0x00000003 : ADCDIFF
Differential ADC output will be used in evaluation
End of enumeration elements list.
SETIF : Enable Interrupt Generation
bits : 14 - 16 (3 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No interrupt is generated
0x00000001 : LEVEL
Set interrupt flag if the sensor triggers.
0x00000002 : POSEDGE
Set interrupt flag on positive edge of the sensor state
0x00000003 : NEGEDGE
Set interrupt flag on negative edge of the sensor state
0x00000004 : BOTHEDGES
Set interrupt flag on both edges of the sensor state
End of enumeration elements list.
EXMODE : Set GPIO Mode
bits : 17 - 18 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Disabled
0x00000001 : HIGH
Push Pull, GPIO is driven high
0x00000002 : LOW
Push Pull, GPIO is driven low
0x00000003 : DACOUT
VDAC output
End of enumeration elements list.
EXCLK : Select Clock Used for Excitation Timing
bits : 19 - 19 (1 bit)
access : read-write
SAMPLECLK : Select Clock Used for Timing of Sample Delay
bits : 20 - 20 (1 bit)
access : read-write
ALTEX : Use Alternative Excite Pin
bits : 21 - 21 (1 bit)
access : read-write
Scan Configuration
address_offset : 0x268 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMPTHRES : Decision Threshold for Sensor Data
bits : 0 - 15 (16 bit)
access : read-write
COMP : Select Mode for Threshold Comparison
bits : 16 - 16 (1 bit)
access : read-write
DECODE : Send Result to Decoder
bits : 17 - 17 (1 bit)
access : read-write
STRSAMPLE : Enable Storing of Sensor Sample in Result Buffer
bits : 18 - 19 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Nothing will be stored in the result buffer.
0x00000001 : DATA
The sensor sample data will be stored in the result buffer.
0x00000002 : DATASRC
The data source (i.e., the channel) will be stored alongside the sensor sample data.
End of enumeration elements list.
SCANRESINV : Enable Inversion of Result
bits : 20 - 20 (1 bit)
access : read-write
MODE : Configure Evaluation Mode
bits : 21 - 22 (2 bit)
access : read-write
Enumeration:
0x00000000 : THRES
Threshold comparison is used to evaluate sensor result
0x00000001 : SLIDINGWIN
Sliding window is used to evaluate sensor result
0x00000002 : STEPDET
Step detection is used to evaluate sensor result
End of enumeration elements list.
Scan Configuration
address_offset : 0x270 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXTIME : Set Excitation Time
bits : 0 - 5 (6 bit)
access : read-write
SAMPLEDLY : Set Sample Delay
bits : 6 - 13 (8 bit)
access : read-write
MEASUREDLY : Set Measure Delay
bits : 14 - 23 (10 bit)
access : read-write
Scan Configuration
address_offset : 0x274 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
THRES : ACMP Threshold or VDAC Data
bits : 0 - 11 (12 bit)
access : read-write
SAMPLE : Select Sample Mode
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
0x00000000 : ACMPCOUNT
Counter output will be used in evaluation
0x00000001 : ACMP
ACMP output will be used in evaluation
0x00000002 : ADC
ADC output will be used in evaluation
0x00000003 : ADCDIFF
Differential ADC output will be used in evaluation
End of enumeration elements list.
SETIF : Enable Interrupt Generation
bits : 14 - 16 (3 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No interrupt is generated
0x00000001 : LEVEL
Set interrupt flag if the sensor triggers.
0x00000002 : POSEDGE
Set interrupt flag on positive edge of the sensor state
0x00000003 : NEGEDGE
Set interrupt flag on negative edge of the sensor state
0x00000004 : BOTHEDGES
Set interrupt flag on both edges of the sensor state
End of enumeration elements list.
EXMODE : Set GPIO Mode
bits : 17 - 18 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Disabled
0x00000001 : HIGH
Push Pull, GPIO is driven high
0x00000002 : LOW
Push Pull, GPIO is driven low
0x00000003 : DACOUT
VDAC output
End of enumeration elements list.
EXCLK : Select Clock Used for Excitation Timing
bits : 19 - 19 (1 bit)
access : read-write
SAMPLECLK : Select Clock Used for Timing of Sample Delay
bits : 20 - 20 (1 bit)
access : read-write
ALTEX : Use Alternative Excite Pin
bits : 21 - 21 (1 bit)
access : read-write
Scan Configuration
address_offset : 0x278 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMPTHRES : Decision Threshold for Sensor Data
bits : 0 - 15 (16 bit)
access : read-write
COMP : Select Mode for Threshold Comparison
bits : 16 - 16 (1 bit)
access : read-write
DECODE : Send Result to Decoder
bits : 17 - 17 (1 bit)
access : read-write
STRSAMPLE : Enable Storing of Sensor Sample in Result Buffer
bits : 18 - 19 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Nothing will be stored in the result buffer.
0x00000001 : DATA
The sensor sample data will be stored in the result buffer.
0x00000002 : DATASRC
The data source (i.e., the channel) will be stored alongside the sensor sample data.
End of enumeration elements list.
SCANRESINV : Enable Inversion of Result
bits : 20 - 20 (1 bit)
access : read-write
MODE : Configure Evaluation Mode
bits : 21 - 22 (2 bit)
access : read-write
Enumeration:
0x00000000 : THRES
Threshold comparison is used to evaluate sensor result
0x00000001 : SLIDINGWIN
Sliding window is used to evaluate sensor result
0x00000002 : STEPDET
Step detection is used to evaluate sensor result
End of enumeration elements list.
Status Register
address_offset : 0x28 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
BUFDATAV : Result Data Valid
bits : 0 - 0 (1 bit)
access : read-only
BUFHALFFULL : Result Buffer Half Full
bits : 1 - 1 (1 bit)
access : read-only
BUFFULL : Result Buffer Full
bits : 2 - 2 (1 bit)
access : read-only
RUNNING : LESENSE Periodic Counter Running
bits : 3 - 3 (1 bit)
access : read-only
SCANACTIVE : LESENSE Scan Active
bits : 4 - 4 (1 bit)
access : read-only
DACACTIVE : LESENSE VDAC Interface is Active
bits : 5 - 5 (1 bit)
access : read-only
Scan Configuration
address_offset : 0x280 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXTIME : Set Excitation Time
bits : 0 - 5 (6 bit)
access : read-write
SAMPLEDLY : Set Sample Delay
bits : 6 - 13 (8 bit)
access : read-write
MEASUREDLY : Set Measure Delay
bits : 14 - 23 (10 bit)
access : read-write
Scan Configuration
address_offset : 0x284 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
THRES : ACMP Threshold or VDAC Data
bits : 0 - 11 (12 bit)
access : read-write
SAMPLE : Select Sample Mode
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
0x00000000 : ACMPCOUNT
Counter output will be used in evaluation
0x00000001 : ACMP
ACMP output will be used in evaluation
0x00000002 : ADC
ADC output will be used in evaluation
0x00000003 : ADCDIFF
Differential ADC output will be used in evaluation
End of enumeration elements list.
SETIF : Enable Interrupt Generation
bits : 14 - 16 (3 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No interrupt is generated
0x00000001 : LEVEL
Set interrupt flag if the sensor triggers.
0x00000002 : POSEDGE
Set interrupt flag on positive edge of the sensor state
0x00000003 : NEGEDGE
Set interrupt flag on negative edge of the sensor state
0x00000004 : BOTHEDGES
Set interrupt flag on both edges of the sensor state
End of enumeration elements list.
EXMODE : Set GPIO Mode
bits : 17 - 18 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Disabled
0x00000001 : HIGH
Push Pull, GPIO is driven high
0x00000002 : LOW
Push Pull, GPIO is driven low
0x00000003 : DACOUT
VDAC output
End of enumeration elements list.
EXCLK : Select Clock Used for Excitation Timing
bits : 19 - 19 (1 bit)
access : read-write
SAMPLECLK : Select Clock Used for Timing of Sample Delay
bits : 20 - 20 (1 bit)
access : read-write
ALTEX : Use Alternative Excite Pin
bits : 21 - 21 (1 bit)
access : read-write
Scan Configuration
address_offset : 0x288 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMPTHRES : Decision Threshold for Sensor Data
bits : 0 - 15 (16 bit)
access : read-write
COMP : Select Mode for Threshold Comparison
bits : 16 - 16 (1 bit)
access : read-write
DECODE : Send Result to Decoder
bits : 17 - 17 (1 bit)
access : read-write
STRSAMPLE : Enable Storing of Sensor Sample in Result Buffer
bits : 18 - 19 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Nothing will be stored in the result buffer.
0x00000001 : DATA
The sensor sample data will be stored in the result buffer.
0x00000002 : DATASRC
The data source (i.e., the channel) will be stored alongside the sensor sample data.
End of enumeration elements list.
SCANRESINV : Enable Inversion of Result
bits : 20 - 20 (1 bit)
access : read-write
MODE : Configure Evaluation Mode
bits : 21 - 22 (2 bit)
access : read-write
Enumeration:
0x00000000 : THRES
Threshold comparison is used to evaluate sensor result
0x00000001 : SLIDINGWIN
Sliding window is used to evaluate sensor result
0x00000002 : STEPDET
Step detection is used to evaluate sensor result
End of enumeration elements list.
Scan Configuration
address_offset : 0x290 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXTIME : Set Excitation Time
bits : 0 - 5 (6 bit)
access : read-write
SAMPLEDLY : Set Sample Delay
bits : 6 - 13 (8 bit)
access : read-write
MEASUREDLY : Set Measure Delay
bits : 14 - 23 (10 bit)
access : read-write
Scan Configuration
address_offset : 0x294 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
THRES : ACMP Threshold or VDAC Data
bits : 0 - 11 (12 bit)
access : read-write
SAMPLE : Select Sample Mode
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
0x00000000 : ACMPCOUNT
Counter output will be used in evaluation
0x00000001 : ACMP
ACMP output will be used in evaluation
0x00000002 : ADC
ADC output will be used in evaluation
0x00000003 : ADCDIFF
Differential ADC output will be used in evaluation
End of enumeration elements list.
SETIF : Enable Interrupt Generation
bits : 14 - 16 (3 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No interrupt is generated
0x00000001 : LEVEL
Set interrupt flag if the sensor triggers.
0x00000002 : POSEDGE
Set interrupt flag on positive edge of the sensor state
0x00000003 : NEGEDGE
Set interrupt flag on negative edge of the sensor state
0x00000004 : BOTHEDGES
Set interrupt flag on both edges of the sensor state
End of enumeration elements list.
EXMODE : Set GPIO Mode
bits : 17 - 18 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Disabled
0x00000001 : HIGH
Push Pull, GPIO is driven high
0x00000002 : LOW
Push Pull, GPIO is driven low
0x00000003 : DACOUT
VDAC output
End of enumeration elements list.
EXCLK : Select Clock Used for Excitation Timing
bits : 19 - 19 (1 bit)
access : read-write
SAMPLECLK : Select Clock Used for Timing of Sample Delay
bits : 20 - 20 (1 bit)
access : read-write
ALTEX : Use Alternative Excite Pin
bits : 21 - 21 (1 bit)
access : read-write
Scan Configuration
address_offset : 0x298 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMPTHRES : Decision Threshold for Sensor Data
bits : 0 - 15 (16 bit)
access : read-write
COMP : Select Mode for Threshold Comparison
bits : 16 - 16 (1 bit)
access : read-write
DECODE : Send Result to Decoder
bits : 17 - 17 (1 bit)
access : read-write
STRSAMPLE : Enable Storing of Sensor Sample in Result Buffer
bits : 18 - 19 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Nothing will be stored in the result buffer.
0x00000001 : DATA
The sensor sample data will be stored in the result buffer.
0x00000002 : DATASRC
The data source (i.e., the channel) will be stored alongside the sensor sample data.
End of enumeration elements list.
SCANRESINV : Enable Inversion of Result
bits : 20 - 20 (1 bit)
access : read-write
MODE : Configure Evaluation Mode
bits : 21 - 22 (2 bit)
access : read-write
Enumeration:
0x00000000 : THRES
Threshold comparison is used to evaluate sensor result
0x00000001 : SLIDINGWIN
Sliding window is used to evaluate sensor result
0x00000002 : STEPDET
Step detection is used to evaluate sensor result
End of enumeration elements list.
Scan Configuration
address_offset : 0x2A0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXTIME : Set Excitation Time
bits : 0 - 5 (6 bit)
access : read-write
SAMPLEDLY : Set Sample Delay
bits : 6 - 13 (8 bit)
access : read-write
MEASUREDLY : Set Measure Delay
bits : 14 - 23 (10 bit)
access : read-write
Scan Configuration
address_offset : 0x2A4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
THRES : ACMP Threshold or VDAC Data
bits : 0 - 11 (12 bit)
access : read-write
SAMPLE : Select Sample Mode
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
0x00000000 : ACMPCOUNT
Counter output will be used in evaluation
0x00000001 : ACMP
ACMP output will be used in evaluation
0x00000002 : ADC
ADC output will be used in evaluation
0x00000003 : ADCDIFF
Differential ADC output will be used in evaluation
End of enumeration elements list.
SETIF : Enable Interrupt Generation
bits : 14 - 16 (3 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No interrupt is generated
0x00000001 : LEVEL
Set interrupt flag if the sensor triggers.
0x00000002 : POSEDGE
Set interrupt flag on positive edge of the sensor state
0x00000003 : NEGEDGE
Set interrupt flag on negative edge of the sensor state
0x00000004 : BOTHEDGES
Set interrupt flag on both edges of the sensor state
End of enumeration elements list.
EXMODE : Set GPIO Mode
bits : 17 - 18 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Disabled
0x00000001 : HIGH
Push Pull, GPIO is driven high
0x00000002 : LOW
Push Pull, GPIO is driven low
0x00000003 : DACOUT
VDAC output
End of enumeration elements list.
EXCLK : Select Clock Used for Excitation Timing
bits : 19 - 19 (1 bit)
access : read-write
SAMPLECLK : Select Clock Used for Timing of Sample Delay
bits : 20 - 20 (1 bit)
access : read-write
ALTEX : Use Alternative Excite Pin
bits : 21 - 21 (1 bit)
access : read-write
Scan Configuration
address_offset : 0x2A8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMPTHRES : Decision Threshold for Sensor Data
bits : 0 - 15 (16 bit)
access : read-write
COMP : Select Mode for Threshold Comparison
bits : 16 - 16 (1 bit)
access : read-write
DECODE : Send Result to Decoder
bits : 17 - 17 (1 bit)
access : read-write
STRSAMPLE : Enable Storing of Sensor Sample in Result Buffer
bits : 18 - 19 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Nothing will be stored in the result buffer.
0x00000001 : DATA
The sensor sample data will be stored in the result buffer.
0x00000002 : DATASRC
The data source (i.e., the channel) will be stored alongside the sensor sample data.
End of enumeration elements list.
SCANRESINV : Enable Inversion of Result
bits : 20 - 20 (1 bit)
access : read-write
MODE : Configure Evaluation Mode
bits : 21 - 22 (2 bit)
access : read-write
Enumeration:
0x00000000 : THRES
Threshold comparison is used to evaluate sensor result
0x00000001 : SLIDINGWIN
Sliding window is used to evaluate sensor result
0x00000002 : STEPDET
Step detection is used to evaluate sensor result
End of enumeration elements list.
Scan Configuration
address_offset : 0x2B0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXTIME : Set Excitation Time
bits : 0 - 5 (6 bit)
access : read-write
SAMPLEDLY : Set Sample Delay
bits : 6 - 13 (8 bit)
access : read-write
MEASUREDLY : Set Measure Delay
bits : 14 - 23 (10 bit)
access : read-write
Scan Configuration
address_offset : 0x2B4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
THRES : ACMP Threshold or VDAC Data
bits : 0 - 11 (12 bit)
access : read-write
SAMPLE : Select Sample Mode
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
0x00000000 : ACMPCOUNT
Counter output will be used in evaluation
0x00000001 : ACMP
ACMP output will be used in evaluation
0x00000002 : ADC
ADC output will be used in evaluation
0x00000003 : ADCDIFF
Differential ADC output will be used in evaluation
End of enumeration elements list.
SETIF : Enable Interrupt Generation
bits : 14 - 16 (3 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No interrupt is generated
0x00000001 : LEVEL
Set interrupt flag if the sensor triggers.
0x00000002 : POSEDGE
Set interrupt flag on positive edge of the sensor state
0x00000003 : NEGEDGE
Set interrupt flag on negative edge of the sensor state
0x00000004 : BOTHEDGES
Set interrupt flag on both edges of the sensor state
End of enumeration elements list.
EXMODE : Set GPIO Mode
bits : 17 - 18 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Disabled
0x00000001 : HIGH
Push Pull, GPIO is driven high
0x00000002 : LOW
Push Pull, GPIO is driven low
0x00000003 : DACOUT
VDAC output
End of enumeration elements list.
EXCLK : Select Clock Used for Excitation Timing
bits : 19 - 19 (1 bit)
access : read-write
SAMPLECLK : Select Clock Used for Timing of Sample Delay
bits : 20 - 20 (1 bit)
access : read-write
ALTEX : Use Alternative Excite Pin
bits : 21 - 21 (1 bit)
access : read-write
Scan Configuration
address_offset : 0x2B8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMPTHRES : Decision Threshold for Sensor Data
bits : 0 - 15 (16 bit)
access : read-write
COMP : Select Mode for Threshold Comparison
bits : 16 - 16 (1 bit)
access : read-write
DECODE : Send Result to Decoder
bits : 17 - 17 (1 bit)
access : read-write
STRSAMPLE : Enable Storing of Sensor Sample in Result Buffer
bits : 18 - 19 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Nothing will be stored in the result buffer.
0x00000001 : DATA
The sensor sample data will be stored in the result buffer.
0x00000002 : DATASRC
The data source (i.e., the channel) will be stored alongside the sensor sample data.
End of enumeration elements list.
SCANRESINV : Enable Inversion of Result
bits : 20 - 20 (1 bit)
access : read-write
MODE : Configure Evaluation Mode
bits : 21 - 22 (2 bit)
access : read-write
Enumeration:
0x00000000 : THRES
Threshold comparison is used to evaluate sensor result
0x00000001 : SLIDINGWIN
Sliding window is used to evaluate sensor result
0x00000002 : STEPDET
Step detection is used to evaluate sensor result
End of enumeration elements list.
Result Buffer Pointers
address_offset : 0x2C Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
RD : Result Buffer Read Pointer
bits : 0 - 3 (4 bit)
access : read-only
WR : Result Buffer Write Pointer
bits : 4 - 7 (4 bit)
access : read-only
Scan Configuration
address_offset : 0x2C0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXTIME : Set Excitation Time
bits : 0 - 5 (6 bit)
access : read-write
SAMPLEDLY : Set Sample Delay
bits : 6 - 13 (8 bit)
access : read-write
MEASUREDLY : Set Measure Delay
bits : 14 - 23 (10 bit)
access : read-write
Scan Configuration
address_offset : 0x2C4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
THRES : ACMP Threshold or VDAC Data
bits : 0 - 11 (12 bit)
access : read-write
SAMPLE : Select Sample Mode
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
0x00000000 : ACMPCOUNT
Counter output will be used in evaluation
0x00000001 : ACMP
ACMP output will be used in evaluation
0x00000002 : ADC
ADC output will be used in evaluation
0x00000003 : ADCDIFF
Differential ADC output will be used in evaluation
End of enumeration elements list.
SETIF : Enable Interrupt Generation
bits : 14 - 16 (3 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No interrupt is generated
0x00000001 : LEVEL
Set interrupt flag if the sensor triggers.
0x00000002 : POSEDGE
Set interrupt flag on positive edge of the sensor state
0x00000003 : NEGEDGE
Set interrupt flag on negative edge of the sensor state
0x00000004 : BOTHEDGES
Set interrupt flag on both edges of the sensor state
End of enumeration elements list.
EXMODE : Set GPIO Mode
bits : 17 - 18 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Disabled
0x00000001 : HIGH
Push Pull, GPIO is driven high
0x00000002 : LOW
Push Pull, GPIO is driven low
0x00000003 : DACOUT
VDAC output
End of enumeration elements list.
EXCLK : Select Clock Used for Excitation Timing
bits : 19 - 19 (1 bit)
access : read-write
SAMPLECLK : Select Clock Used for Timing of Sample Delay
bits : 20 - 20 (1 bit)
access : read-write
ALTEX : Use Alternative Excite Pin
bits : 21 - 21 (1 bit)
access : read-write
Scan Configuration
address_offset : 0x2C8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMPTHRES : Decision Threshold for Sensor Data
bits : 0 - 15 (16 bit)
access : read-write
COMP : Select Mode for Threshold Comparison
bits : 16 - 16 (1 bit)
access : read-write
DECODE : Send Result to Decoder
bits : 17 - 17 (1 bit)
access : read-write
STRSAMPLE : Enable Storing of Sensor Sample in Result Buffer
bits : 18 - 19 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Nothing will be stored in the result buffer.
0x00000001 : DATA
The sensor sample data will be stored in the result buffer.
0x00000002 : DATASRC
The data source (i.e., the channel) will be stored alongside the sensor sample data.
End of enumeration elements list.
SCANRESINV : Enable Inversion of Result
bits : 20 - 20 (1 bit)
access : read-write
MODE : Configure Evaluation Mode
bits : 21 - 22 (2 bit)
access : read-write
Enumeration:
0x00000000 : THRES
Threshold comparison is used to evaluate sensor result
0x00000001 : SLIDINGWIN
Sliding window is used to evaluate sensor result
0x00000002 : STEPDET
Step detection is used to evaluate sensor result
End of enumeration elements list.
Scan Configuration
address_offset : 0x2D0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXTIME : Set Excitation Time
bits : 0 - 5 (6 bit)
access : read-write
SAMPLEDLY : Set Sample Delay
bits : 6 - 13 (8 bit)
access : read-write
MEASUREDLY : Set Measure Delay
bits : 14 - 23 (10 bit)
access : read-write
Scan Configuration
address_offset : 0x2D4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
THRES : ACMP Threshold or VDAC Data
bits : 0 - 11 (12 bit)
access : read-write
SAMPLE : Select Sample Mode
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
0x00000000 : ACMPCOUNT
Counter output will be used in evaluation
0x00000001 : ACMP
ACMP output will be used in evaluation
0x00000002 : ADC
ADC output will be used in evaluation
0x00000003 : ADCDIFF
Differential ADC output will be used in evaluation
End of enumeration elements list.
SETIF : Enable Interrupt Generation
bits : 14 - 16 (3 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No interrupt is generated
0x00000001 : LEVEL
Set interrupt flag if the sensor triggers.
0x00000002 : POSEDGE
Set interrupt flag on positive edge of the sensor state
0x00000003 : NEGEDGE
Set interrupt flag on negative edge of the sensor state
0x00000004 : BOTHEDGES
Set interrupt flag on both edges of the sensor state
End of enumeration elements list.
EXMODE : Set GPIO Mode
bits : 17 - 18 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Disabled
0x00000001 : HIGH
Push Pull, GPIO is driven high
0x00000002 : LOW
Push Pull, GPIO is driven low
0x00000003 : DACOUT
VDAC output
End of enumeration elements list.
EXCLK : Select Clock Used for Excitation Timing
bits : 19 - 19 (1 bit)
access : read-write
SAMPLECLK : Select Clock Used for Timing of Sample Delay
bits : 20 - 20 (1 bit)
access : read-write
ALTEX : Use Alternative Excite Pin
bits : 21 - 21 (1 bit)
access : read-write
Scan Configuration
address_offset : 0x2D8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMPTHRES : Decision Threshold for Sensor Data
bits : 0 - 15 (16 bit)
access : read-write
COMP : Select Mode for Threshold Comparison
bits : 16 - 16 (1 bit)
access : read-write
DECODE : Send Result to Decoder
bits : 17 - 17 (1 bit)
access : read-write
STRSAMPLE : Enable Storing of Sensor Sample in Result Buffer
bits : 18 - 19 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Nothing will be stored in the result buffer.
0x00000001 : DATA
The sensor sample data will be stored in the result buffer.
0x00000002 : DATASRC
The data source (i.e., the channel) will be stored alongside the sensor sample data.
End of enumeration elements list.
SCANRESINV : Enable Inversion of Result
bits : 20 - 20 (1 bit)
access : read-write
MODE : Configure Evaluation Mode
bits : 21 - 22 (2 bit)
access : read-write
Enumeration:
0x00000000 : THRES
Threshold comparison is used to evaluate sensor result
0x00000001 : SLIDINGWIN
Sliding window is used to evaluate sensor result
0x00000002 : STEPDET
Step detection is used to evaluate sensor result
End of enumeration elements list.
Scan Configuration
address_offset : 0x2E0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXTIME : Set Excitation Time
bits : 0 - 5 (6 bit)
access : read-write
SAMPLEDLY : Set Sample Delay
bits : 6 - 13 (8 bit)
access : read-write
MEASUREDLY : Set Measure Delay
bits : 14 - 23 (10 bit)
access : read-write
Scan Configuration
address_offset : 0x2E4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
THRES : ACMP Threshold or VDAC Data
bits : 0 - 11 (12 bit)
access : read-write
SAMPLE : Select Sample Mode
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
0x00000000 : ACMPCOUNT
Counter output will be used in evaluation
0x00000001 : ACMP
ACMP output will be used in evaluation
0x00000002 : ADC
ADC output will be used in evaluation
0x00000003 : ADCDIFF
Differential ADC output will be used in evaluation
End of enumeration elements list.
SETIF : Enable Interrupt Generation
bits : 14 - 16 (3 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No interrupt is generated
0x00000001 : LEVEL
Set interrupt flag if the sensor triggers.
0x00000002 : POSEDGE
Set interrupt flag on positive edge of the sensor state
0x00000003 : NEGEDGE
Set interrupt flag on negative edge of the sensor state
0x00000004 : BOTHEDGES
Set interrupt flag on both edges of the sensor state
End of enumeration elements list.
EXMODE : Set GPIO Mode
bits : 17 - 18 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Disabled
0x00000001 : HIGH
Push Pull, GPIO is driven high
0x00000002 : LOW
Push Pull, GPIO is driven low
0x00000003 : DACOUT
VDAC output
End of enumeration elements list.
EXCLK : Select Clock Used for Excitation Timing
bits : 19 - 19 (1 bit)
access : read-write
SAMPLECLK : Select Clock Used for Timing of Sample Delay
bits : 20 - 20 (1 bit)
access : read-write
ALTEX : Use Alternative Excite Pin
bits : 21 - 21 (1 bit)
access : read-write
Scan Configuration
address_offset : 0x2E8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMPTHRES : Decision Threshold for Sensor Data
bits : 0 - 15 (16 bit)
access : read-write
COMP : Select Mode for Threshold Comparison
bits : 16 - 16 (1 bit)
access : read-write
DECODE : Send Result to Decoder
bits : 17 - 17 (1 bit)
access : read-write
STRSAMPLE : Enable Storing of Sensor Sample in Result Buffer
bits : 18 - 19 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Nothing will be stored in the result buffer.
0x00000001 : DATA
The sensor sample data will be stored in the result buffer.
0x00000002 : DATASRC
The data source (i.e., the channel) will be stored alongside the sensor sample data.
End of enumeration elements list.
SCANRESINV : Enable Inversion of Result
bits : 20 - 20 (1 bit)
access : read-write
MODE : Configure Evaluation Mode
bits : 21 - 22 (2 bit)
access : read-write
Enumeration:
0x00000000 : THRES
Threshold comparison is used to evaluate sensor result
0x00000001 : SLIDINGWIN
Sliding window is used to evaluate sensor result
0x00000002 : STEPDET
Step detection is used to evaluate sensor result
End of enumeration elements list.
Scan Configuration
address_offset : 0x2F0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXTIME : Set Excitation Time
bits : 0 - 5 (6 bit)
access : read-write
SAMPLEDLY : Set Sample Delay
bits : 6 - 13 (8 bit)
access : read-write
MEASUREDLY : Set Measure Delay
bits : 14 - 23 (10 bit)
access : read-write
Scan Configuration
address_offset : 0x2F4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
THRES : ACMP Threshold or VDAC Data
bits : 0 - 11 (12 bit)
access : read-write
SAMPLE : Select Sample Mode
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
0x00000000 : ACMPCOUNT
Counter output will be used in evaluation
0x00000001 : ACMP
ACMP output will be used in evaluation
0x00000002 : ADC
ADC output will be used in evaluation
0x00000003 : ADCDIFF
Differential ADC output will be used in evaluation
End of enumeration elements list.
SETIF : Enable Interrupt Generation
bits : 14 - 16 (3 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No interrupt is generated
0x00000001 : LEVEL
Set interrupt flag if the sensor triggers.
0x00000002 : POSEDGE
Set interrupt flag on positive edge of the sensor state
0x00000003 : NEGEDGE
Set interrupt flag on negative edge of the sensor state
0x00000004 : BOTHEDGES
Set interrupt flag on both edges of the sensor state
End of enumeration elements list.
EXMODE : Set GPIO Mode
bits : 17 - 18 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Disabled
0x00000001 : HIGH
Push Pull, GPIO is driven high
0x00000002 : LOW
Push Pull, GPIO is driven low
0x00000003 : DACOUT
VDAC output
End of enumeration elements list.
EXCLK : Select Clock Used for Excitation Timing
bits : 19 - 19 (1 bit)
access : read-write
SAMPLECLK : Select Clock Used for Timing of Sample Delay
bits : 20 - 20 (1 bit)
access : read-write
ALTEX : Use Alternative Excite Pin
bits : 21 - 21 (1 bit)
access : read-write
Scan Configuration
address_offset : 0x2F8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMPTHRES : Decision Threshold for Sensor Data
bits : 0 - 15 (16 bit)
access : read-write
COMP : Select Mode for Threshold Comparison
bits : 16 - 16 (1 bit)
access : read-write
DECODE : Send Result to Decoder
bits : 17 - 17 (1 bit)
access : read-write
STRSAMPLE : Enable Storing of Sensor Sample in Result Buffer
bits : 18 - 19 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Nothing will be stored in the result buffer.
0x00000001 : DATA
The sensor sample data will be stored in the result buffer.
0x00000002 : DATASRC
The data source (i.e., the channel) will be stored alongside the sensor sample data.
End of enumeration elements list.
SCANRESINV : Enable Inversion of Result
bits : 20 - 20 (1 bit)
access : read-write
MODE : Configure Evaluation Mode
bits : 21 - 22 (2 bit)
access : read-write
Enumeration:
0x00000000 : THRES
Threshold comparison is used to evaluate sensor result
0x00000001 : SLIDINGWIN
Sliding window is used to evaluate sensor result
0x00000002 : STEPDET
Step detection is used to evaluate sensor result
End of enumeration elements list.
Result Buffer Data Register
address_offset : 0x30 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
BUFDATA : Result Data
bits : 0 - 15 (16 bit)
access : read-only
BUFDATASRC : Result Data Source
bits : 16 - 19 (4 bit)
access : read-only
Scan Configuration
address_offset : 0x300 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXTIME : Set Excitation Time
bits : 0 - 5 (6 bit)
access : read-write
SAMPLEDLY : Set Sample Delay
bits : 6 - 13 (8 bit)
access : read-write
MEASUREDLY : Set Measure Delay
bits : 14 - 23 (10 bit)
access : read-write
Scan Configuration
address_offset : 0x304 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
THRES : ACMP Threshold or VDAC Data
bits : 0 - 11 (12 bit)
access : read-write
SAMPLE : Select Sample Mode
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
0x00000000 : ACMPCOUNT
Counter output will be used in evaluation
0x00000001 : ACMP
ACMP output will be used in evaluation
0x00000002 : ADC
ADC output will be used in evaluation
0x00000003 : ADCDIFF
Differential ADC output will be used in evaluation
End of enumeration elements list.
SETIF : Enable Interrupt Generation
bits : 14 - 16 (3 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No interrupt is generated
0x00000001 : LEVEL
Set interrupt flag if the sensor triggers.
0x00000002 : POSEDGE
Set interrupt flag on positive edge of the sensor state
0x00000003 : NEGEDGE
Set interrupt flag on negative edge of the sensor state
0x00000004 : BOTHEDGES
Set interrupt flag on both edges of the sensor state
End of enumeration elements list.
EXMODE : Set GPIO Mode
bits : 17 - 18 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Disabled
0x00000001 : HIGH
Push Pull, GPIO is driven high
0x00000002 : LOW
Push Pull, GPIO is driven low
0x00000003 : DACOUT
VDAC output
End of enumeration elements list.
EXCLK : Select Clock Used for Excitation Timing
bits : 19 - 19 (1 bit)
access : read-write
SAMPLECLK : Select Clock Used for Timing of Sample Delay
bits : 20 - 20 (1 bit)
access : read-write
ALTEX : Use Alternative Excite Pin
bits : 21 - 21 (1 bit)
access : read-write
Scan Configuration
address_offset : 0x308 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMPTHRES : Decision Threshold for Sensor Data
bits : 0 - 15 (16 bit)
access : read-write
COMP : Select Mode for Threshold Comparison
bits : 16 - 16 (1 bit)
access : read-write
DECODE : Send Result to Decoder
bits : 17 - 17 (1 bit)
access : read-write
STRSAMPLE : Enable Storing of Sensor Sample in Result Buffer
bits : 18 - 19 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Nothing will be stored in the result buffer.
0x00000001 : DATA
The sensor sample data will be stored in the result buffer.
0x00000002 : DATASRC
The data source (i.e., the channel) will be stored alongside the sensor sample data.
End of enumeration elements list.
SCANRESINV : Enable Inversion of Result
bits : 20 - 20 (1 bit)
access : read-write
MODE : Configure Evaluation Mode
bits : 21 - 22 (2 bit)
access : read-write
Enumeration:
0x00000000 : THRES
Threshold comparison is used to evaluate sensor result
0x00000001 : SLIDINGWIN
Sliding window is used to evaluate sensor result
0x00000002 : STEPDET
Step detection is used to evaluate sensor result
End of enumeration elements list.
Scan Configuration
address_offset : 0x310 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXTIME : Set Excitation Time
bits : 0 - 5 (6 bit)
access : read-write
SAMPLEDLY : Set Sample Delay
bits : 6 - 13 (8 bit)
access : read-write
MEASUREDLY : Set Measure Delay
bits : 14 - 23 (10 bit)
access : read-write
Scan Configuration
address_offset : 0x314 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
THRES : ACMP Threshold or VDAC Data
bits : 0 - 11 (12 bit)
access : read-write
SAMPLE : Select Sample Mode
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
0x00000000 : ACMPCOUNT
Counter output will be used in evaluation
0x00000001 : ACMP
ACMP output will be used in evaluation
0x00000002 : ADC
ADC output will be used in evaluation
0x00000003 : ADCDIFF
Differential ADC output will be used in evaluation
End of enumeration elements list.
SETIF : Enable Interrupt Generation
bits : 14 - 16 (3 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No interrupt is generated
0x00000001 : LEVEL
Set interrupt flag if the sensor triggers.
0x00000002 : POSEDGE
Set interrupt flag on positive edge of the sensor state
0x00000003 : NEGEDGE
Set interrupt flag on negative edge of the sensor state
0x00000004 : BOTHEDGES
Set interrupt flag on both edges of the sensor state
End of enumeration elements list.
EXMODE : Set GPIO Mode
bits : 17 - 18 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Disabled
0x00000001 : HIGH
Push Pull, GPIO is driven high
0x00000002 : LOW
Push Pull, GPIO is driven low
0x00000003 : DACOUT
VDAC output
End of enumeration elements list.
EXCLK : Select Clock Used for Excitation Timing
bits : 19 - 19 (1 bit)
access : read-write
SAMPLECLK : Select Clock Used for Timing of Sample Delay
bits : 20 - 20 (1 bit)
access : read-write
ALTEX : Use Alternative Excite Pin
bits : 21 - 21 (1 bit)
access : read-write
Scan Configuration
address_offset : 0x318 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMPTHRES : Decision Threshold for Sensor Data
bits : 0 - 15 (16 bit)
access : read-write
COMP : Select Mode for Threshold Comparison
bits : 16 - 16 (1 bit)
access : read-write
DECODE : Send Result to Decoder
bits : 17 - 17 (1 bit)
access : read-write
STRSAMPLE : Enable Storing of Sensor Sample in Result Buffer
bits : 18 - 19 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Nothing will be stored in the result buffer.
0x00000001 : DATA
The sensor sample data will be stored in the result buffer.
0x00000002 : DATASRC
The data source (i.e., the channel) will be stored alongside the sensor sample data.
End of enumeration elements list.
SCANRESINV : Enable Inversion of Result
bits : 20 - 20 (1 bit)
access : read-write
MODE : Configure Evaluation Mode
bits : 21 - 22 (2 bit)
access : read-write
Enumeration:
0x00000000 : THRES
Threshold comparison is used to evaluate sensor result
0x00000001 : SLIDINGWIN
Sliding window is used to evaluate sensor result
0x00000002 : STEPDET
Step detection is used to evaluate sensor result
End of enumeration elements list.
Scan Configuration
address_offset : 0x320 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXTIME : Set Excitation Time
bits : 0 - 5 (6 bit)
access : read-write
SAMPLEDLY : Set Sample Delay
bits : 6 - 13 (8 bit)
access : read-write
MEASUREDLY : Set Measure Delay
bits : 14 - 23 (10 bit)
access : read-write
Scan Configuration
address_offset : 0x324 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
THRES : ACMP Threshold or VDAC Data
bits : 0 - 11 (12 bit)
access : read-write
SAMPLE : Select Sample Mode
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
0x00000000 : ACMPCOUNT
Counter output will be used in evaluation
0x00000001 : ACMP
ACMP output will be used in evaluation
0x00000002 : ADC
ADC output will be used in evaluation
0x00000003 : ADCDIFF
Differential ADC output will be used in evaluation
End of enumeration elements list.
SETIF : Enable Interrupt Generation
bits : 14 - 16 (3 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No interrupt is generated
0x00000001 : LEVEL
Set interrupt flag if the sensor triggers.
0x00000002 : POSEDGE
Set interrupt flag on positive edge of the sensor state
0x00000003 : NEGEDGE
Set interrupt flag on negative edge of the sensor state
0x00000004 : BOTHEDGES
Set interrupt flag on both edges of the sensor state
End of enumeration elements list.
EXMODE : Set GPIO Mode
bits : 17 - 18 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Disabled
0x00000001 : HIGH
Push Pull, GPIO is driven high
0x00000002 : LOW
Push Pull, GPIO is driven low
0x00000003 : DACOUT
VDAC output
End of enumeration elements list.
EXCLK : Select Clock Used for Excitation Timing
bits : 19 - 19 (1 bit)
access : read-write
SAMPLECLK : Select Clock Used for Timing of Sample Delay
bits : 20 - 20 (1 bit)
access : read-write
ALTEX : Use Alternative Excite Pin
bits : 21 - 21 (1 bit)
access : read-write
Scan Configuration
address_offset : 0x328 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMPTHRES : Decision Threshold for Sensor Data
bits : 0 - 15 (16 bit)
access : read-write
COMP : Select Mode for Threshold Comparison
bits : 16 - 16 (1 bit)
access : read-write
DECODE : Send Result to Decoder
bits : 17 - 17 (1 bit)
access : read-write
STRSAMPLE : Enable Storing of Sensor Sample in Result Buffer
bits : 18 - 19 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Nothing will be stored in the result buffer.
0x00000001 : DATA
The sensor sample data will be stored in the result buffer.
0x00000002 : DATASRC
The data source (i.e., the channel) will be stored alongside the sensor sample data.
End of enumeration elements list.
SCANRESINV : Enable Inversion of Result
bits : 20 - 20 (1 bit)
access : read-write
MODE : Configure Evaluation Mode
bits : 21 - 22 (2 bit)
access : read-write
Enumeration:
0x00000000 : THRES
Threshold comparison is used to evaluate sensor result
0x00000001 : SLIDINGWIN
Sliding window is used to evaluate sensor result
0x00000002 : STEPDET
Step detection is used to evaluate sensor result
End of enumeration elements list.
Scan Configuration
address_offset : 0x330 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
EXTIME : Set Excitation Time
bits : 0 - 5 (6 bit)
access : read-write
SAMPLEDLY : Set Sample Delay
bits : 6 - 13 (8 bit)
access : read-write
MEASUREDLY : Set Measure Delay
bits : 14 - 23 (10 bit)
access : read-write
Scan Configuration
address_offset : 0x334 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
THRES : ACMP Threshold or VDAC Data
bits : 0 - 11 (12 bit)
access : read-write
SAMPLE : Select Sample Mode
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
0x00000000 : ACMPCOUNT
Counter output will be used in evaluation
0x00000001 : ACMP
ACMP output will be used in evaluation
0x00000002 : ADC
ADC output will be used in evaluation
0x00000003 : ADCDIFF
Differential ADC output will be used in evaluation
End of enumeration elements list.
SETIF : Enable Interrupt Generation
bits : 14 - 16 (3 bit)
access : read-write
Enumeration:
0x00000000 : NONE
No interrupt is generated
0x00000001 : LEVEL
Set interrupt flag if the sensor triggers.
0x00000002 : POSEDGE
Set interrupt flag on positive edge of the sensor state
0x00000003 : NEGEDGE
Set interrupt flag on negative edge of the sensor state
0x00000004 : BOTHEDGES
Set interrupt flag on both edges of the sensor state
End of enumeration elements list.
EXMODE : Set GPIO Mode
bits : 17 - 18 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Disabled
0x00000001 : HIGH
Push Pull, GPIO is driven high
0x00000002 : LOW
Push Pull, GPIO is driven low
0x00000003 : DACOUT
VDAC output
End of enumeration elements list.
EXCLK : Select Clock Used for Excitation Timing
bits : 19 - 19 (1 bit)
access : read-write
SAMPLECLK : Select Clock Used for Timing of Sample Delay
bits : 20 - 20 (1 bit)
access : read-write
ALTEX : Use Alternative Excite Pin
bits : 21 - 21 (1 bit)
access : read-write
Scan Configuration
address_offset : 0x338 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
COMPTHRES : Decision Threshold for Sensor Data
bits : 0 - 15 (16 bit)
access : read-write
COMP : Select Mode for Threshold Comparison
bits : 16 - 16 (1 bit)
access : read-write
DECODE : Send Result to Decoder
bits : 17 - 17 (1 bit)
access : read-write
STRSAMPLE : Enable Storing of Sensor Sample in Result Buffer
bits : 18 - 19 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
Nothing will be stored in the result buffer.
0x00000001 : DATA
The sensor sample data will be stored in the result buffer.
0x00000002 : DATASRC
The data source (i.e., the channel) will be stored alongside the sensor sample data.
End of enumeration elements list.
SCANRESINV : Enable Inversion of Result
bits : 20 - 20 (1 bit)
access : read-write
MODE : Configure Evaluation Mode
bits : 21 - 22 (2 bit)
access : read-write
Enumeration:
0x00000000 : THRES
Threshold comparison is used to evaluate sensor result
0x00000001 : SLIDINGWIN
Sliding window is used to evaluate sensor result
0x00000002 : STEPDET
Step detection is used to evaluate sensor result
End of enumeration elements list.
Current Channel Index
address_offset : 0x34 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
CURCH : Current Channel Index
bits : 0 - 3 (4 bit)
access : read-only
Current Decoder State
address_offset : 0x38 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DECSTATE : Current Decoder State
bits : 0 - 4 (5 bit)
access : read-write
Decoder Input Register
address_offset : 0x3C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SENSORSTATE : Decoder Input Register
bits : 0 - 3 (4 bit)
access : read-write
Timing Control Register
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
AUXPRESC : Prescaling Factor for High Frequency Timer
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
0x00000000 : DIV1
High frequency timer is clocked with AUXHFRCO/1
0x00000001 : DIV2
High frequency timer is clocked with AUXHFRCO/2
0x00000002 : DIV4
High frequency timer is clocked with AUXHFRCO/4
0x00000003 : DIV8
High frequency timer is clocked with AUXHFRCO/8
End of enumeration elements list.
LFPRESC : Prescaling Factor for Low Frequency Timer
bits : 4 - 6 (3 bit)
access : read-write
Enumeration:
0x00000000 : DIV1
Low frequency timer is clocked with LFACLKLESENSE/1
0x00000001 : DIV2
Low frequency timer is clocked with LFACLKLESENSE/2
0x00000002 : DIV4
Low frequency timer is clocked with LFACLKLESENSE/4
0x00000003 : DIV8
Low frequency timer is clocked with LFACLKLESENSE/8
0x00000004 : DIV16
Low frequency timer is clocked with LFACLKLESENSE/16
0x00000005 : DIV32
Low frequency timer is clocked with LFACLKLESENSE/32
0x00000006 : DIV64
Low frequency timer is clocked with LFACLKLESENSE/64
0x00000007 : DIV128
Low frequency timer is clocked with LFACLKLESENSE/128
End of enumeration elements list.
PCPRESC : Period Counter Prescaling
bits : 8 - 10 (3 bit)
access : read-write
Enumeration:
0x00000000 : DIV1
The period counter clock frequency is LFACLKLESENSE/1
0x00000001 : DIV2
The period counter clock frequency is LFACLKLESENSE/2
0x00000002 : DIV4
The period counter clock frequency is LFACLKLESENSE/4
0x00000003 : DIV8
The period counter clock frequency is LFACLKLESENSE/8
0x00000004 : DIV16
The period counter clock frequency is LFACLKLESENSE/16
0x00000005 : DIV32
The period counter clock frequency is LFACLKLESENSE/32
0x00000006 : DIV64
The period counter clock frequency is LFACLKLESENSE/64
0x00000007 : DIV128
The period counter clock frequency is LFACLKLESENSE/128
End of enumeration elements list.
PCTOP : Period Counter Top Value
bits : 12 - 19 (8 bit)
access : read-write
STARTDLY : Start Delay Configuration
bits : 22 - 23 (2 bit)
access : read-write
AUXSTARTUP : AUXHFRCO Startup Configuration
bits : 28 - 28 (1 bit)
access : read-write
GPIO Idle Phase Configuration
address_offset : 0x40 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CH0 : Channel 0 Idle Phase Configuration
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
CH0 output is disabled in idle phase
0x00000001 : HIGH
CH0 output is high in idle phase
0x00000002 : LOW
CH0 output is low in idle phase
0x00000003 : DAC
CH0 output is connected to VDAC output in idle phase. Note that this mode is only available on channels 0, 1, 2, 3, 12, 13, 14, 15
End of enumeration elements list.
CH1 : Channel 1 Idle Phase Configuration
bits : 2 - 3 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
CH1 output is disabled in idle phase
0x00000001 : HIGH
CH1 output is high in idle phase
0x00000002 : LOW
CH1 output is low in idle phase
0x00000003 : DAC
CH1 output is connected to VDAC output in idle phase. Note that this mode is only available on channels 0, 1, 2, 3, 12, 13, 14, 15
End of enumeration elements list.
CH2 : Channel 2 Idle Phase Configuration
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
CH2 output is disabled in idle phase
0x00000001 : HIGH
CH2 output is high in idle phase
0x00000002 : LOW
CH2 output is low in idle phase
0x00000003 : DAC
CH2 output is connected to VDAC output in idle phase. Note that this mode is only available on channels 0, 1, 2, 3, 12, 13, 14, 15
End of enumeration elements list.
CH3 : Channel 3 Idle Phase Configuration
bits : 6 - 7 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
CH3 output is disabled in idle phase
0x00000001 : HIGH
CH3 output is high in idle phase
0x00000002 : LOW
CH3 output is low in idle phase
0x00000003 : DAC
CH3 output is connected to VDAC output in idle phase. Note that this mode is only available on channels 0, 1, 2, 3, 12, 13, 14, 15
End of enumeration elements list.
CH4 : Channel 4 Idle Phase Configuration
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
CH4 output is disabled in idle phase
0x00000001 : HIGH
CH4 output is high in idle phase
0x00000002 : LOW
CH4 output is low in idle phase
0x00000003 : DAC
CH4 output is connected to VDAC output in idle phase. Note that this mode is only available on channels 0, 1, 2, 3, 12, 13, 14, 15
End of enumeration elements list.
CH5 : Channel 5 Idle Phase Configuration
bits : 10 - 11 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
CH5 output is disabled in idle phase
0x00000001 : HIGH
CH5 output is high in idle phase
0x00000002 : LOW
CH5 output is low in idle phase
0x00000003 : DAC
CH5 output is connected to VDAC output in idle phase. Note that this mode is only available on channels 0, 1, 2, 3, 12, 13, 14, 15
End of enumeration elements list.
CH6 : Channel 6 Idle Phase Configuration
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
CH6 output is disabled in idle phase
0x00000001 : HIGH
CH6 output is high in idle phase
0x00000002 : LOW
CH6 output is low in idle phase
0x00000003 : DAC
CH6 output is connected to VDAC output in idle phase. Note that this mode is only available on channels 0, 1, 2, 3, 12, 13, 14, 15
End of enumeration elements list.
CH7 : Channel 7 Idle Phase Configuration
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
CH7 output is disabled in idle phase
0x00000001 : HIGH
CH7 output is high in idle phase
0x00000002 : LOW
CH7 output is low in idle phase
0x00000003 : DAC
CH7 output is connected to VDAC output in idle phase. Note that this mode is only available on channels 0, 1, 2, 3, 12, 13, 14, 15
End of enumeration elements list.
CH8 : Channel 8 Idle Phase Configuration
bits : 16 - 17 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
CH8 output is disabled in idle phase
0x00000001 : HIGH
CH8 output is high in idle phase
0x00000002 : LOW
CH8 output is low in idle phase
0x00000003 : DAC
CH8 output is connected to VDAC output in idle phase. Note that this mode is only available on channels 0, 1, 2, 3, 12, 13, 14, 15
End of enumeration elements list.
CH9 : Channel 9 Idle Phase Configuration
bits : 18 - 19 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
CH9 output is disabled in idle phase
0x00000001 : HIGH
CH9 output is high in idle phase
0x00000002 : LOW
CH9 output is low in idle phase
0x00000003 : DAC
CH9 output is connected to VDAC output in idle phase. Note that this mode is only available on channels 0, 1, 2, 3, 12, 13, 14, 15
End of enumeration elements list.
CH10 : Channel 10 Idle Phase Configuration
bits : 20 - 21 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
CH10 output is disabled in idle phase
0x00000001 : HIGH
CH10 output is high in idle phase
0x00000002 : LOW
CH10 output is low in idle phase
0x00000003 : DAC
CH10 output is connected to VDAC output in idle phase. Note that this mode is only available on channels 0, 1, 2, 3, 12, 13, 14, 15
End of enumeration elements list.
CH11 : Channel 11 Idle Phase Configuration
bits : 22 - 23 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
CH11 output is disabled in idle phase
0x00000001 : HIGH
CH11 output is high in idle phase
0x00000002 : LOW
CH11 output is low in idle phase
0x00000003 : DAC
CH11 output is connected to VDAC output in idle phase. Note that this mode is only available on channels 0, 1, 2, 3, 12, 13, 14, 15
End of enumeration elements list.
CH12 : Channel 12 Idle Phase Configuration
bits : 24 - 25 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
CH12 output is disabled in idle phase
0x00000001 : HIGH
CH12 output is high in idle phase
0x00000002 : LOW
CH12 output is low in idle phase
0x00000003 : DAC
CH12 output is connected to VDAC output in idle phase. Note that this mode is only available on channels 0, 1, 2, 3, 12, 13, 14, 15
End of enumeration elements list.
CH13 : Channel 13 Idle Phase Configuration
bits : 26 - 27 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
CH13 output is disabled in idle phase
0x00000001 : HIGH
CH13 output is high in idle phase
0x00000002 : LOW
CH13 output is low in idle phase
0x00000003 : DAC
CH13 output is connected to VDAC output in idle phase. Note that this mode is only available on channels 0, 1, 2, 3, 12, 13, 14, 15
End of enumeration elements list.
CH14 : Channel 14 Idle Phase Configuration
bits : 28 - 29 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
CH14 output is disabled in idle phase
0x00000001 : HIGH
CH14 output is high in idle phase
0x00000002 : LOW
CH14 output is low in idle phase
0x00000003 : DAC
CH14 output is connected to VDAC output in idle phase. Note that this mode is only available on channels 0, 1, 2, 3, 12, 13, 14, 15
End of enumeration elements list.
CH15 : Channel 15 Idle Phase Configuration
bits : 30 - 31 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
CH15 output is disabled in idle phase
0x00000001 : HIGH
CH15 output is high in idle phase
0x00000002 : LOW
CH15 output is low in idle phase
0x00000003 : DAC
CH15 output is connected to VDAC output in idle phase. Note that this mode is only available on channels 0, 1, 2, 3, 12, 13, 14, 15
End of enumeration elements list.
Alternative Excite Pin Configuration
address_offset : 0x44 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
IDLECONF0 : ALTEX0 Idle Phase Configuration
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
ALTEX0 output is disabled in idle phase
0x00000001 : HIGH
ALTEX0 output is high in idle phase
0x00000002 : LOW
ALTEX0 output is low in idle phase
End of enumeration elements list.
IDLECONF1 : ALTEX1 Idle Phase Configuration
bits : 2 - 3 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
ALTEX1 output is disabled in idle phase
0x00000001 : HIGH
ALTEX1 output is high in idle phase
0x00000002 : LOW
ALTEX1 output is low in idle phase
End of enumeration elements list.
IDLECONF2 : ALTEX2 Idle Phase Configuration
bits : 4 - 5 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
ALTEX2 output is disabled in idle phase
0x00000001 : HIGH
ALTEX2 output is high in idle phase
0x00000002 : LOW
ALTEX2 output is low in idle phase
End of enumeration elements list.
IDLECONF3 : ALTEX3 Idle Phase Configuration
bits : 6 - 7 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
ALTEX3 output is disabled in idle phase
0x00000001 : HIGH
ALTEX3 output is high in idle phase
0x00000002 : LOW
ALTEX3 output is low in idle phase
End of enumeration elements list.
IDLECONF4 : ALTEX4 Idle Phase Configuration
bits : 8 - 9 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
ALTEX4 output is disabled in idle phase
0x00000001 : HIGH
ALTEX4 output is high in idle phase
0x00000002 : LOW
ALTEX4 output is low in idle phase
End of enumeration elements list.
IDLECONF5 : ALTEX5 Idle Phase Configuration
bits : 10 - 11 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
ALTEX5 output is disabled in idle phase
0x00000001 : HIGH
ALTEX5 output is high in idle phase
0x00000002 : LOW
ALTEX5 output is low in idle phase
End of enumeration elements list.
IDLECONF6 : ALTEX6 Idle Phase Configuration
bits : 12 - 13 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
ALTEX6 output is disabled in idle phase
0x00000001 : HIGH
ALTEX6 output is high in idle phase
0x00000002 : LOW
ALTEX6 output is low in idle phase
End of enumeration elements list.
IDLECONF7 : ALTEX7 Idle Phase Configuration
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
ALTEX7 output is disabled in idle phase
0x00000001 : HIGH
ALTEX7 output is high in idle phase
0x00000002 : LOW
ALTEX7 output is low in idle phase
End of enumeration elements list.
AEX0 : ALTEX0 Always Excite Enable
bits : 16 - 16 (1 bit)
access : read-write
AEX1 : ALTEX1 Always Excite Enable
bits : 17 - 17 (1 bit)
access : read-write
AEX2 : ALTEX2 Always Excite Enable
bits : 18 - 18 (1 bit)
access : read-write
AEX3 : ALTEX3 Always Excite Enable
bits : 19 - 19 (1 bit)
access : read-write
AEX4 : ALTEX4 Always Excite Enable
bits : 20 - 20 (1 bit)
access : read-write
AEX5 : ALTEX5 Always Excite Enable
bits : 21 - 21 (1 bit)
access : read-write
AEX6 : ALTEX6 Always Excite Enable
bits : 22 - 22 (1 bit)
access : read-write
AEX7 : ALTEX7 Always Excite Enable
bits : 23 - 23 (1 bit)
access : read-write
Interrupt Flag Register
address_offset : 0x50 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
CH0 : CH0 Interrupt Flag
bits : 0 - 0 (1 bit)
access : read-only
CH1 : CH1 Interrupt Flag
bits : 1 - 1 (1 bit)
access : read-only
CH2 : CH2 Interrupt Flag
bits : 2 - 2 (1 bit)
access : read-only
CH3 : CH3 Interrupt Flag
bits : 3 - 3 (1 bit)
access : read-only
CH4 : CH4 Interrupt Flag
bits : 4 - 4 (1 bit)
access : read-only
CH5 : CH5 Interrupt Flag
bits : 5 - 5 (1 bit)
access : read-only
CH6 : CH6 Interrupt Flag
bits : 6 - 6 (1 bit)
access : read-only
CH7 : CH7 Interrupt Flag
bits : 7 - 7 (1 bit)
access : read-only
CH8 : CH8 Interrupt Flag
bits : 8 - 8 (1 bit)
access : read-only
CH9 : CH9 Interrupt Flag
bits : 9 - 9 (1 bit)
access : read-only
CH10 : CH10 Interrupt Flag
bits : 10 - 10 (1 bit)
access : read-only
CH11 : CH11 Interrupt Flag
bits : 11 - 11 (1 bit)
access : read-only
CH12 : CH12 Interrupt Flag
bits : 12 - 12 (1 bit)
access : read-only
CH13 : CH13 Interrupt Flag
bits : 13 - 13 (1 bit)
access : read-only
CH14 : CH14 Interrupt Flag
bits : 14 - 14 (1 bit)
access : read-only
CH15 : CH15 Interrupt Flag
bits : 15 - 15 (1 bit)
access : read-only
SCANCOMPLETE : SCANCOMPLETE Interrupt Flag
bits : 16 - 16 (1 bit)
access : read-only
DEC : DEC Interrupt Flag
bits : 17 - 17 (1 bit)
access : read-only
DECERR : DECERR Interrupt Flag
bits : 18 - 18 (1 bit)
access : read-only
BUFDATAV : BUFDATAV Interrupt Flag
bits : 19 - 19 (1 bit)
access : read-only
BUFLEVEL : BUFLEVEL Interrupt Flag
bits : 20 - 20 (1 bit)
access : read-only
BUFOF : BUFOF Interrupt Flag
bits : 21 - 21 (1 bit)
access : read-only
CNTOF : CNTOF Interrupt Flag
bits : 22 - 22 (1 bit)
access : read-only
Interrupt Flag Set Register
address_offset : 0x54 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
CH0 : Set CH0 Interrupt Flag
bits : 0 - 0 (1 bit)
access : write-only
CH1 : Set CH1 Interrupt Flag
bits : 1 - 1 (1 bit)
access : write-only
CH2 : Set CH2 Interrupt Flag
bits : 2 - 2 (1 bit)
access : write-only
CH3 : Set CH3 Interrupt Flag
bits : 3 - 3 (1 bit)
access : write-only
CH4 : Set CH4 Interrupt Flag
bits : 4 - 4 (1 bit)
access : write-only
CH5 : Set CH5 Interrupt Flag
bits : 5 - 5 (1 bit)
access : write-only
CH6 : Set CH6 Interrupt Flag
bits : 6 - 6 (1 bit)
access : write-only
CH7 : Set CH7 Interrupt Flag
bits : 7 - 7 (1 bit)
access : write-only
CH8 : Set CH8 Interrupt Flag
bits : 8 - 8 (1 bit)
access : write-only
CH9 : Set CH9 Interrupt Flag
bits : 9 - 9 (1 bit)
access : write-only
CH10 : Set CH10 Interrupt Flag
bits : 10 - 10 (1 bit)
access : write-only
CH11 : Set CH11 Interrupt Flag
bits : 11 - 11 (1 bit)
access : write-only
CH12 : Set CH12 Interrupt Flag
bits : 12 - 12 (1 bit)
access : write-only
CH13 : Set CH13 Interrupt Flag
bits : 13 - 13 (1 bit)
access : write-only
CH14 : Set CH14 Interrupt Flag
bits : 14 - 14 (1 bit)
access : write-only
CH15 : Set CH15 Interrupt Flag
bits : 15 - 15 (1 bit)
access : write-only
SCANCOMPLETE : Set SCANCOMPLETE Interrupt Flag
bits : 16 - 16 (1 bit)
access : write-only
DEC : Set DEC Interrupt Flag
bits : 17 - 17 (1 bit)
access : write-only
DECERR : Set DECERR Interrupt Flag
bits : 18 - 18 (1 bit)
access : write-only
BUFDATAV : Set BUFDATAV Interrupt Flag
bits : 19 - 19 (1 bit)
access : write-only
BUFLEVEL : Set BUFLEVEL Interrupt Flag
bits : 20 - 20 (1 bit)
access : write-only
BUFOF : Set BUFOF Interrupt Flag
bits : 21 - 21 (1 bit)
access : write-only
CNTOF : Set CNTOF Interrupt Flag
bits : 22 - 22 (1 bit)
access : write-only
Interrupt Flag Clear Register
address_offset : 0x58 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
CH0 : Clear CH0 Interrupt Flag
bits : 0 - 0 (1 bit)
access : write-only
CH1 : Clear CH1 Interrupt Flag
bits : 1 - 1 (1 bit)
access : write-only
CH2 : Clear CH2 Interrupt Flag
bits : 2 - 2 (1 bit)
access : write-only
CH3 : Clear CH3 Interrupt Flag
bits : 3 - 3 (1 bit)
access : write-only
CH4 : Clear CH4 Interrupt Flag
bits : 4 - 4 (1 bit)
access : write-only
CH5 : Clear CH5 Interrupt Flag
bits : 5 - 5 (1 bit)
access : write-only
CH6 : Clear CH6 Interrupt Flag
bits : 6 - 6 (1 bit)
access : write-only
CH7 : Clear CH7 Interrupt Flag
bits : 7 - 7 (1 bit)
access : write-only
CH8 : Clear CH8 Interrupt Flag
bits : 8 - 8 (1 bit)
access : write-only
CH9 : Clear CH9 Interrupt Flag
bits : 9 - 9 (1 bit)
access : write-only
CH10 : Clear CH10 Interrupt Flag
bits : 10 - 10 (1 bit)
access : write-only
CH11 : Clear CH11 Interrupt Flag
bits : 11 - 11 (1 bit)
access : write-only
CH12 : Clear CH12 Interrupt Flag
bits : 12 - 12 (1 bit)
access : write-only
CH13 : Clear CH13 Interrupt Flag
bits : 13 - 13 (1 bit)
access : write-only
CH14 : Clear CH14 Interrupt Flag
bits : 14 - 14 (1 bit)
access : write-only
CH15 : Clear CH15 Interrupt Flag
bits : 15 - 15 (1 bit)
access : write-only
SCANCOMPLETE : Clear SCANCOMPLETE Interrupt Flag
bits : 16 - 16 (1 bit)
access : write-only
DEC : Clear DEC Interrupt Flag
bits : 17 - 17 (1 bit)
access : write-only
DECERR : Clear DECERR Interrupt Flag
bits : 18 - 18 (1 bit)
access : write-only
BUFDATAV : Clear BUFDATAV Interrupt Flag
bits : 19 - 19 (1 bit)
access : write-only
BUFLEVEL : Clear BUFLEVEL Interrupt Flag
bits : 20 - 20 (1 bit)
access : write-only
BUFOF : Clear BUFOF Interrupt Flag
bits : 21 - 21 (1 bit)
access : write-only
CNTOF : Clear CNTOF Interrupt Flag
bits : 22 - 22 (1 bit)
access : write-only
Interrupt Enable Register
address_offset : 0x5C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CH0 : CH0 Interrupt Enable
bits : 0 - 0 (1 bit)
access : read-write
CH1 : CH1 Interrupt Enable
bits : 1 - 1 (1 bit)
access : read-write
CH2 : CH2 Interrupt Enable
bits : 2 - 2 (1 bit)
access : read-write
CH3 : CH3 Interrupt Enable
bits : 3 - 3 (1 bit)
access : read-write
CH4 : CH4 Interrupt Enable
bits : 4 - 4 (1 bit)
access : read-write
CH5 : CH5 Interrupt Enable
bits : 5 - 5 (1 bit)
access : read-write
CH6 : CH6 Interrupt Enable
bits : 6 - 6 (1 bit)
access : read-write
CH7 : CH7 Interrupt Enable
bits : 7 - 7 (1 bit)
access : read-write
CH8 : CH8 Interrupt Enable
bits : 8 - 8 (1 bit)
access : read-write
CH9 : CH9 Interrupt Enable
bits : 9 - 9 (1 bit)
access : read-write
CH10 : CH10 Interrupt Enable
bits : 10 - 10 (1 bit)
access : read-write
CH11 : CH11 Interrupt Enable
bits : 11 - 11 (1 bit)
access : read-write
CH12 : CH12 Interrupt Enable
bits : 12 - 12 (1 bit)
access : read-write
CH13 : CH13 Interrupt Enable
bits : 13 - 13 (1 bit)
access : read-write
CH14 : CH14 Interrupt Enable
bits : 14 - 14 (1 bit)
access : read-write
CH15 : CH15 Interrupt Enable
bits : 15 - 15 (1 bit)
access : read-write
SCANCOMPLETE : SCANCOMPLETE Interrupt Enable
bits : 16 - 16 (1 bit)
access : read-write
DEC : DEC Interrupt Enable
bits : 17 - 17 (1 bit)
access : read-write
DECERR : DECERR Interrupt Enable
bits : 18 - 18 (1 bit)
access : read-write
BUFDATAV : BUFDATAV Interrupt Enable
bits : 19 - 19 (1 bit)
access : read-write
BUFLEVEL : BUFLEVEL Interrupt Enable
bits : 20 - 20 (1 bit)
access : read-write
BUFOF : BUFOF Interrupt Enable
bits : 21 - 21 (1 bit)
access : read-write
CNTOF : CNTOF Interrupt Enable
bits : 22 - 22 (1 bit)
access : read-write
Synchronization Busy Register
address_offset : 0x60 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
CMD : CMD Register Busy
bits : 7 - 7 (1 bit)
access : read-only
I/O Routing Register
address_offset : 0x64 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CH0PEN : CH0 Pin Enable
bits : 0 - 0 (1 bit)
access : read-write
CH1PEN : CH1 Pin Enable
bits : 1 - 1 (1 bit)
access : read-write
CH2PEN : CH2 Pin Enable
bits : 2 - 2 (1 bit)
access : read-write
CH3PEN : CH3 Pin Enable
bits : 3 - 3 (1 bit)
access : read-write
CH4PEN : CH4 Pin Enable
bits : 4 - 4 (1 bit)
access : read-write
CH5PEN : CH5 Pin Enable
bits : 5 - 5 (1 bit)
access : read-write
CH6PEN : CH6 Pin Enable
bits : 6 - 6 (1 bit)
access : read-write
CH7PEN : CH7 Pin Enable
bits : 7 - 7 (1 bit)
access : read-write
CH8PEN : CH8 Pin Enable
bits : 8 - 8 (1 bit)
access : read-write
CH9PEN : CH9 Pin Enable
bits : 9 - 9 (1 bit)
access : read-write
CH10PEN : CH10 Pin Enable
bits : 10 - 10 (1 bit)
access : read-write
CH11PEN : CH11 Pin Enable
bits : 11 - 11 (1 bit)
access : read-write
CH12PEN : CH12 Pin Enable
bits : 12 - 12 (1 bit)
access : read-write
CH13PEN : CH13 Pin Enable
bits : 13 - 13 (1 bit)
access : read-write
CH14PEN : CH14 Pin Enable
bits : 14 - 14 (1 bit)
access : read-write
CH15PEN : CH15 Pin Enable
bits : 15 - 15 (1 bit)
access : read-write
ALTEX0PEN : ALTEX0 Pin Enable
bits : 16 - 16 (1 bit)
access : read-write
ALTEX1PEN : ALTEX1 Pin Enable
bits : 17 - 17 (1 bit)
access : read-write
ALTEX2PEN : ALTEX2 Pin Enable
bits : 18 - 18 (1 bit)
access : read-write
ALTEX3PEN : ALTEX3 Pin Enable
bits : 19 - 19 (1 bit)
access : read-write
ALTEX4PEN : ALTEX4 Pin Enable
bits : 20 - 20 (1 bit)
access : read-write
ALTEX5PEN : ALTEX5 Pin Enable
bits : 21 - 21 (1 bit)
access : read-write
ALTEX6PEN : ALTEX6 Pin Enable
bits : 22 - 22 (1 bit)
access : read-write
ALTEX7PEN : ALTEX7 Pin Enable
bits : 23 - 23 (1 bit)
access : read-write
Peripheral Control Register
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DACCH0EN : VDAC CH0 Enable
bits : 0 - 0 (1 bit)
access : read-write
DACCH1EN : VDAC CH1 Enable
bits : 1 - 1 (1 bit)
access : read-write
DACCH0DATA : VDAC CH0 Data Selection
bits : 2 - 2 (1 bit)
access : read-write
DACCH1DATA : VDAC CH1 Data Selection
bits : 3 - 3 (1 bit)
access : read-write
DACSTARTUP : VDAC Startup Configuration
bits : 6 - 6 (1 bit)
access : read-write
DACCONVTRIG : VDAC Conversion Trigger Configuration
bits : 8 - 8 (1 bit)
access : read-write
ACMP0MODE : ACMP0 Mode
bits : 20 - 21 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
LESENSE does not control ACMP0
0x00000001 : MUX
LESENSE controls the input mux (POSSEL) of ACMP0
0x00000002 : MUXTHRES
LESENSE controls the input mux (POSSEL) and the threshold value (VDDLEVEL) of ACMP0
End of enumeration elements list.
ACMP1MODE : ACMP1 Mode
bits : 22 - 23 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
LESENSE does not control ACMP1
0x00000001 : MUX
LESENSE controls the input mux (POSSEL) of ACMP1
0x00000002 : MUXTHRES
LESENSE controls the input mux and the threshold value (VDDLEVEL) of ACMP1
End of enumeration elements list.
ACMP0INV : Invert Analog Comparator 0 Output
bits : 24 - 24 (1 bit)
access : read-write
ACMP1INV : Invert Analog Comparator 1 Output
bits : 25 - 25 (1 bit)
access : read-write
ACMP0HYSTEN : ACMP0 Hysteresis Enable
bits : 26 - 26 (1 bit)
access : read-write
ACMP1HYSTEN : ACMP1 Hysteresis Enable
bits : 27 - 27 (1 bit)
access : read-write
WARMUPMODE : ACMP and VDAC Duty Cycle Mode
bits : 28 - 29 (2 bit)
access : read-write
Enumeration:
0x00000000 : NORMAL
The analog comparators and VDAC are shut down when LESENSE is idle
0x00000001 : KEEPACMPWARM
The analog comparators are kept powered up when LESENSE is idle
0x00000002 : KEEPDACWARM
The VDAC is kept powered up when LESENSE is idle
0x00000003 : KEEPACMPDACWARM
The analog comparators and VDAC are kept powered up when LESENSE is idle
End of enumeration elements list.
Decoder Control Register
address_offset : 0xC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DISABLE : Disable the Decoder
bits : 0 - 0 (1 bit)
access : read-write
ERRCHK : Enable Check of Current State
bits : 1 - 1 (1 bit)
access : read-write
INTMAP : Enable Decoder to Channel Interrupt Mapping
bits : 2 - 2 (1 bit)
access : read-write
HYSTPRS0 : Enable Decoder Hysteresis on PRS0 Output
bits : 3 - 3 (1 bit)
access : read-write
HYSTPRS1 : Enable Decoder Hysteresis on PRS1 Output
bits : 4 - 4 (1 bit)
access : read-write
HYSTPRS2 : Enable Decoder Hysteresis on PRS2 Output
bits : 5 - 5 (1 bit)
access : read-write
HYSTIRQ : Enable Decoder Hysteresis on Interrupt Requests
bits : 6 - 6 (1 bit)
access : read-write
PRSCNT : Enable Count Mode on Decoder PRS Channels 0 and 1
bits : 7 - 7 (1 bit)
access : read-write
INPUT : LESENSE Decoder Input Configuration
bits : 8 - 8 (1 bit)
access : read-write
PRSSEL0 : LESENSE Decoder PRS Input 0 Configuration
bits : 10 - 13 (4 bit)
access : read-write
Enumeration:
0x00000000 : PRSCH0
PRS Channel 0 selected as input
0x00000001 : PRSCH1
PRS Channel 1 selected as input
0x00000002 : PRSCH2
PRS Channel 2 selected as input
0x00000003 : PRSCH3
PRS Channel 3 selected as input
0x00000004 : PRSCH4
PRS Channel 4 selected as input
0x00000005 : PRSCH5
PRS Channel 5 selected as input
0x00000006 : PRSCH6
PRS Channel 6 selected as input
0x00000007 : PRSCH7
PRS Channel 7 selected as input
0x00000008 : PRSCH8
PRS Channel 8 selected as input
0x00000009 : PRSCH9
PRS Channel 9 selected as input
0x0000000A : PRSCH10
PRS Channel 10 selected as input
0x0000000B : PRSCH11
PRS Channel 11 selected as input
0x0000000C : PRSCH12
PRS Channel 12 selected as input
0x0000000D : PRSCH13
PRS Channel 13 selected as input
0x0000000E : PRSCH14
PRS Channel 14 selected as input
0x0000000F : PRSCH15
PRS Channel 15 selected as input
End of enumeration elements list.
PRSSEL1 : LESENSE Decoder PRS Input 1 Configuration
bits : 15 - 18 (4 bit)
access : read-write
Enumeration:
0x00000000 : PRSCH0
PRS Channel 0 selected as input
0x00000001 : PRSCH1
PRS Channel 1 selected as input
0x00000002 : PRSCH2
PRS Channel 2 selected as input
0x00000003 : PRSCH3
PRS Channel 3 selected as input
0x00000004 : PRSCH4
PRS Channel 4 selected as input
0x00000005 : PRSCH5
PRS Channel 5 selected as input
0x00000006 : PRSCH6
PRS Channel 6 selected as input
0x00000007 : PRSCH7
PRS Channel 7 selected as input
0x00000008 : PRSCH8
PRS Channel 8 selected as input
0x00000009 : PRSCH9
PRS Channel 9 selected as input
0x0000000A : PRSCH10
PRS Channel 10 selected as input
0x0000000B : PRSCH11
PRS Channel 11 selected as input
0x0000000C : PRSCH12
PRS Channel 12 selected as input
0x0000000D : PRSCH13
PRS Channel 13 selected as input
0x0000000E : PRSCH14
PRS Channel 14 selected as input
0x0000000F : PRSCH15
PRS Channel 15 selected as input
End of enumeration elements list.
PRSSEL2 : LESENSE Decoder PRS Input 2 Configuration
bits : 20 - 23 (4 bit)
access : read-write
Enumeration:
0x00000000 : PRSCH0
PRS Channel 0 selected as input
0x00000001 : PRSCH1
PRS Channel 1 selected as input
0x00000002 : PRSCH2
PRS Channel 2 selected as input
0x00000003 : PRSCH3
PRS Channel 3 selected as input
0x00000004 : PRSCH4
PRS Channel 4 selected as input
0x00000005 : PRSCH5
PRS Channel 5 selected as input
0x00000006 : PRSCH6
PRS Channel 6 selected as input
0x00000007 : PRSCH7
PRS Channel 7 selected as input
0x00000008 : PRSCH8
PRS Channel 8 selected as input
0x00000009 : PRSCH9
PRS Channel 9 selected as input
0x0000000A : PRSCH10
PRS Channel 10 selected as input
0x0000000B : PRSCH11
PRS Channel 11 selected as input
0x0000000C : PRSCH12
PRS Channel 12 selected as input
0x0000000D : PRSCH13
PRS Channel 13 selected as input
0x0000000E : PRSCH14
PRS Channel 14 selected as input
0x0000000F : PRSCH15
PRS Channel 15 selected as input
End of enumeration elements list.
PRSSEL3 : LESENSE Decoder PRS Input 3 Configuration
bits : 25 - 28 (4 bit)
access : read-write
Enumeration:
0x00000000 : PRSCH0
PRS Channel 0 selected as input
0x00000001 : PRSCH1
PRS Channel 1 selected as input
0x00000002 : PRSCH2
PRS Channel 2 selected as input
0x00000003 : PRSCH3
PRS Channel 3 selected as input
0x00000004 : PRSCH4
PRS Channel 4 selected as input
0x00000005 : PRSCH5
PRS Channel 5 selected as input
0x00000006 : PRSCH6
PRS Channel 6 selected as input
0x00000007 : PRSCH7
PRS Channel 7 selected as input
0x00000008 : PRSCH8
PRS Channel 8 selected as input
0x00000009 : PRSCH9
PRS Channel 9 selected as input
0x0000000A : PRSCH10
PRS Channel 10 selected as input
0x0000000B : PRSCH11
PRS Channel 11 selected as input
0x0000000C : PRSCH12
PRS Channel 12 selected as input
0x0000000D : PRSCH13
PRS Channel 13 selected as input
0x0000000E : PRSCH14
PRS Channel 14 selected as input
0x0000000F : PRSCH15
PRS Channel 15 selected as input
End of enumeration elements list.
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.