Embeetle, an IDE designed from scratch for embedded software developers.address_offset : 0x0 Bytes (0x0)
size : 0x400 byte (0x0)
mem_usage : registers
protection : not protected
control register 1
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CEN : Counter enable Note: Gated mode can work only if the CEN bit has been previously set by software. However trigger mode can set the CEN bit automatically by hardware. CEN is cleared automatically in one-pulse mode, when an update event occurs.
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
0x0 : B_0x0
Counter disabled
0x1 : B_0x1
Counter enabled
End of enumeration elements list.
UDIS : Update disable This bit is set and cleared by software to enable/disable UEV event generation. Counter overflow/underflow Setting the UG bit Update generation through the slave mode controller Buffered registers are then loaded with their preload values.
bits : 1 - 1 (1 bit)
access : read-write
Enumeration:
0x0 : B_0x0
UEV enabled. The Update (UEV) event is generated by one of the following events:
0x1 : B_0x1
UEV disabled. The Update event is not generated, shadow registers keep their value (ARR, PSC). However the counter and the prescaler are reinitialized if the UG bit is set or if a hardware reset is received from the slave mode controller.
End of enumeration elements list.
URS : Update request source This bit is set and cleared by software to select the UEV event sources. Counter overflow/underflow Setting the UG bit Update generation through the slave mode controller
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
0x0 : B_0x0
Any of the following events generates an update interrupt or DMA request if enabled. These events can be:
0x1 : B_0x1
Only counter overflow/underflow generates an update interrupt or DMA request if enabled.
End of enumeration elements list.
OPM : One-pulse mode
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
0x0 : B_0x0
Counter is not stopped at update event
0x1 : B_0x1
Counter stops counting at the next update event (clearing the CEN bit).
End of enumeration elements list.
ARPE : Auto-reload preload enable
bits : 7 - 7 (1 bit)
access : read-write
Enumeration:
0x0 : B_0x0
TIMx_ARR register is not buffered.
0x1 : B_0x1
TIMx_ARR register is buffered.
End of enumeration elements list.
UIFREMAP : UIF status bit remapping
bits : 11 - 11 (1 bit)
access : read-write
Enumeration:
0x0 : B_0x0
No remapping. UIF status bit is not copied to TIMx_CNT register bit 31.
0x1 : B_0x1
Remapping enabled. UIF status bit is copied to TIMx_CNT register bit 31.
End of enumeration elements list.
status register
address_offset : 0x10 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
UIF : Update interrupt flag This bit is set by hardware on an update event. It is cleared by software. At overflow or underflow regarding the repetition counter value and if UDIS = 0 in the TIMx_CR1 register. When CNT is reinitialized by software using the UG bit in the TIMx_EGR register, if URS = 0 and UDIS = 0 in the TIMx_CR1 register.
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
0x0 : B_0x0
No update occurred.
0x1 : B_0x1
Update interrupt pending. This bit is set by hardware when the registers are updated:
End of enumeration elements list.
event generation register
address_offset : 0x14 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
UG : Update generation This bit can be set by software, it is automatically cleared by hardware.
bits : 0 - 0 (1 bit)
access : write-only
Enumeration:
0x0 : B_0x0
No action.
0x1 : B_0x1
Re-initializes the timer counter and generates an update of the registers. Note that the prescaler counter is cleared too (but the prescaler ratio is not affected).
End of enumeration elements list.
counter
address_offset : 0x24 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
CNT : Counter value
bits : 0 - 15 (16 bit)
access : read-write
UIFCPY : UIF Copy This bit is a read-only copy of the UIF bit of the TIMx_ISR register. If the UIFREMAP bit in TIMx_CR1 is reset, bit 31 is reserved and read as 0.
bits : 31 - 31 (1 bit)
access : read-only
prescaler
address_offset : 0x28 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PSC : Prescaler value
bits : 0 - 15 (16 bit)
auto-reload register
address_offset : 0x2C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ARR : Prescaler value
bits : 0 - 15 (16 bit)
control register 2
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MMS : Master mode selection These bits are used to select the information to be sent in master mode to slave timers for synchronization (TRGO). The combination is as follows: When the Counter Enable signal is controlled by the trigger input, there is a delay on TRGO, except if the master/slave mode is selected (see the MSM bit description in the TIMx_SMCR register). Note: The clock of the slave timer or ADC must be enabled prior to receive events from the master timer, and must not be changed on-the-fly while triggers are received from the master timer.
bits : 4 - 6 (3 bit)
access : read-write
Enumeration:
0x0 : B_0x0
Reset - the UG bit from the TIMx_EGR register is used as a trigger output (TRGO). If reset is generated by the trigger input (slave mode controller configured in reset mode) then the signal on TRGO is delayed compared to the actual reset.
0x1 : B_0x1
Enable - the Counter enable signal, CNT_EN, is used as a trigger output (TRGO). It is useful to start several timers at the same time or to control a window in which a slave timer is enabled. The Counter Enable signal is generated by a logic OR between CEN control bit and the trigger input when configured in gated mode.
0x2 : B_0x2
Update - The update event is selected as a trigger output (TRGO). For instance a master timer can then be used as a prescaler for a slave timer.
End of enumeration elements list.
DMA/Interrupt enable register
address_offset : 0xC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
UIE : Update interrupt enable
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
0x0 : B_0x0
Update interrupt disabled.
0x1 : B_0x1
Update interrupt enabled.
End of enumeration elements list.
UDE : Update DMA request enable
bits : 8 - 8 (1 bit)
access : read-write
Enumeration:
0x0 : B_0x0
Update DMA request disabled.
0x1 : B_0x1
Update DMA request enabled.
End of enumeration elements list.
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.