\n
address_offset : 0x0 Bytes (0x0)
size : 0x400 byte (0x0)
mem_usage : registers
protection : not protected
Control Register
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
MODE : Mode Select
bits : 0 - 1 (2 bit)
access : read-write
Enumeration:
0x00000000 : DISABLE
The module is disabled.
0x00000001 : OVSSINGLE
Single input LFACLK oversampling mode (available in EM0-EM2).
0x00000002 : EXTCLKSINGLE
Externally clocked single input counter mode (available in EM0-EM3).
0x00000003 : EXTCLKQUAD
Externally clocked quadrature decoder mode (available in EM0-EM3).
End of enumeration elements list.
CNTDIR : Non-Quadrature Mode Counter Direction Control
bits : 2 - 2 (1 bit)
access : read-write
EDGE : Edge Select
bits : 3 - 3 (1 bit)
access : read-write
FILT : Enable Digital Pulse Width Filter
bits : 4 - 4 (1 bit)
access : read-write
RSTEN : Enable PCNT Clock Domain Reset
bits : 5 - 5 (1 bit)
access : read-write
HYST : Enable Hysteresis
bits : 8 - 8 (1 bit)
access : read-write
S1CDIR : Count direction determined by S1
bits : 9 - 9 (1 bit)
access : read-write
CNTEV : Controls when the counter counts
bits : 10 - 11 (2 bit)
access : read-write
Enumeration:
0x00000000 : BOTH
Counts up on up-count and down on down-count events.
0x00000001 : UP
Only counts up on up-count events.
0x00000002 : DOWN
Only counts down on down-count events.
0x00000003 : NONE
Never counts.
End of enumeration elements list.
AUXCNTEV : Controls when the auxiliary counter counts
bits : 14 - 15 (2 bit)
access : read-write
Enumeration:
0x00000000 : NONE
Never counts.
0x00000001 : UP
Counts up on up-count events.
0x00000002 : DOWN
Counts up on down-count events.
0x00000003 : BOTH
Counts up on both up-count and down-count events.
End of enumeration elements list.
Top Value Register
address_offset : 0x10 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
TOP : Counter Top Value
bits : 0 - 15 (16 bit)
access : read-only
Top Value Buffer Register
address_offset : 0x14 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TOPB : Counter Top Buffer
bits : 0 - 15 (16 bit)
access : read-write
Interrupt Flag Register
address_offset : 0x18 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
UF : Underflow Interrupt Read Flag
bits : 0 - 0 (1 bit)
access : read-only
OF : Overflow Interrupt Read Flag
bits : 1 - 1 (1 bit)
access : read-only
DIRCNG : Direction Change Detect Interrupt Flag
bits : 2 - 2 (1 bit)
access : read-only
AUXOF : Overflow Interrupt Read Flag
bits : 3 - 3 (1 bit)
access : read-only
Interrupt Flag Set Register
address_offset : 0x1C Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
UF : Underflow interrupt set
bits : 0 - 0 (1 bit)
access : write-only
OF : Overflow Interrupt Set
bits : 1 - 1 (1 bit)
access : write-only
DIRCNG : Direction Change Detect Interrupt Set
bits : 2 - 2 (1 bit)
access : write-only
AUXOF : Auxiliary Overflow Interrupt Set
bits : 3 - 3 (1 bit)
access : write-only
Interrupt Flag Clear Register
address_offset : 0x20 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
UF : Underflow Interrupt Clear
bits : 0 - 0 (1 bit)
access : write-only
OF : Overflow Interrupt Clear
bits : 1 - 1 (1 bit)
access : write-only
DIRCNG : Direction Change Detect Interrupt Clear
bits : 2 - 2 (1 bit)
access : write-only
AUXOF : Auxiliary Overflow Interrupt Clear
bits : 3 - 3 (1 bit)
access : write-only
Interrupt Enable Register
address_offset : 0x24 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
UF : Underflow Interrupt Enable
bits : 0 - 0 (1 bit)
access : read-write
OF : Overflow Interrupt Enable
bits : 1 - 1 (1 bit)
access : read-write
DIRCNG : Direction Change Detect Interrupt Enable
bits : 2 - 2 (1 bit)
access : read-write
AUXOF : Auxiliary Overflow Interrupt Enable
bits : 3 - 3 (1 bit)
access : read-write
I/O Routing Register
address_offset : 0x28 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
LOCATION : I/O Location
bits : 8 - 10 (3 bit)
access : read-write
Enumeration:
0x00000000 : LOC0
Location 0
0x00000001 : LOC1
Location 1
0x00000002 : LOC2
Location 2
0x00000003 : LOC3
Location 3
End of enumeration elements list.
Freeze Register
address_offset : 0x2C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
REGFREEZE : Register Update Freeze
bits : 0 - 0 (1 bit)
access : read-write
Synchronization Busy Register
address_offset : 0x30 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
CTRL : CTRL Register Busy
bits : 0 - 0 (1 bit)
access : read-only
CMD : CMD Register Busy
bits : 1 - 1 (1 bit)
access : read-only
TOPB : TOPB Register Busy
bits : 2 - 2 (1 bit)
access : read-only
Auxiliary Counter Value Register
address_offset : 0x38 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
AUXCNT : Auxiliary Counter Value
bits : 0 - 15 (16 bit)
access : read-write
PCNT Input Register
address_offset : 0x3C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
S0PRSSEL : S0IN PRS Channel Select
bits : 0 - 3 (4 bit)
access : read-write
Enumeration:
0x00000000 : PRSCH0
PRS Channel 0 selected.
0x00000001 : PRSCH1
PRS Channel 1 selected.
0x00000002 : PRSCH2
PRS Channel 2 selected.
0x00000003 : PRSCH3
PRS Channel 3 selected.
0x00000004 : PRSCH4
PRS Channel 4 selected.
0x00000005 : PRSCH5
PRS Channel 5 selected.
0x00000006 : PRSCH6
PRS Channel 6 selected.
0x00000007 : PRSCH7
PRS Channel 7 selected.
0x00000008 : PRSCH8
PRS Channel 8 selected.
0x00000009 : PRSCH9
PRS Channel 9 selected.
0x0000000A : PRSCH10
PRS Channel 10 selected.
0x0000000B : PRSCH11
PRS Channel 11 selected.
End of enumeration elements list.
S0PRSEN : S0IN PRS Enable
bits : 4 - 4 (1 bit)
access : read-write
S1PRSSEL : S1IN PRS Channel Select
bits : 6 - 9 (4 bit)
access : read-write
Enumeration:
0x00000000 : PRSCH0
PRS Channel 0 selected.
0x00000001 : PRSCH1
PRS Channel 1 selected.
0x00000002 : PRSCH2
PRS Channel 2 selected.
0x00000003 : PRSCH3
PRS Channel 3 selected.
0x00000004 : PRSCH4
PRS Channel 4 selected.
0x00000005 : PRSCH5
PRS Channel 5 selected.
0x00000006 : PRSCH6
PRS Channel 6 selected.
0x00000007 : PRSCH7
PRS Channel 7 selected.
0x00000008 : PRSCH8
PRS Channel 8 selected.
0x00000009 : PRSCH9
PRS Channel 9 selected.
0x0000000A : PRSCH10
PRS Channel 10 selected.
0x0000000B : PRSCH11
PRS Channel 11 selected.
End of enumeration elements list.
S1PRSEN : S1IN PRS Enable
bits : 10 - 10 (1 bit)
access : read-write
Command Register
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0
LCNTIM : Load CNT Immediately
bits : 0 - 0 (1 bit)
access : write-only
LTOPBIM : Load TOPB Immediately
bits : 1 - 1 (1 bit)
access : write-only
Status Register
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
DIR : Current Counter Direction
bits : 0 - 0 (1 bit)
access : read-only
Counter Value Register
address_offset : 0xC Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0
CNT : Counter Value
bits : 0 - 15 (16 bit)
access : read-only
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.