\n

DAC0

Peripheral Memory Blocks

address_offset : 0x0 Bytes (0x0)
size : 0x400 byte (0x0)
mem_usage : registers
protection : not protected

Registers

CTRL

IEN

IF

IFS

IFC

CH0DATA

CH1DATA

COMBDATA

CAL

BIASPROG

STATUS

OPACTRL

OPAOFFSET

OPA0MUX

OPA1MUX

OPA2MUX

CH0CTRL

CH1CTRL


CTRL

Control Register
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

CTRL CTRL read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 DIFF SINEMODE CONVMODE OUTMODE OUTENPRS CH0PRESCRST REFSEL PRESC REFRSEL

DIFF : Differential Mode
bits : 0 - 0 (1 bit)
access : read-write

SINEMODE : Sine Mode
bits : 1 - 1 (1 bit)
access : read-write

CONVMODE : Conversion Mode
bits : 2 - 3 (2 bit)
access : read-write

Enumeration:

0x00000000 : CONTINUOUS

DAC is set in continuous mode

0x00000001 : SAMPLEHOLD

DAC is set in sample/hold mode

0x00000002 : SAMPLEOFF

DAC is set in sample/shut off mode

End of enumeration elements list.

OUTMODE : Output Mode
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0x00000000 : DISABLE

DAC output to pin and ADC disabled

0x00000001 : PIN

DAC output to pin enabled. DAC output to ADC and ACMP disabled

0x00000002 : ADC

DAC output to pin disabled. DAC output to ADC and ACMP enabled

0x00000003 : PINADC

DAC output to pin, ADC, and ACMP enabled

End of enumeration elements list.

OUTENPRS : PRS Controlled Output Enable
bits : 6 - 6 (1 bit)
access : read-write

CH0PRESCRST : Channel 0 Start Reset Prescaler
bits : 7 - 7 (1 bit)
access : read-write

REFSEL : Reference Selection
bits : 8 - 9 (2 bit)
access : read-write

Enumeration:

0x00000000 : 1V25

Internal 1.25 V bandgap reference

0x00000001 : 2V5

Internal 2.5 V bandgap reference

0x00000002 : VDD

VDD reference

End of enumeration elements list.

PRESC : Prescaler Setting
bits : 16 - 18 (3 bit)
access : read-write

Enumeration:

0x00000000 : NODIVISION

None

End of enumeration elements list.

REFRSEL : Refresh Interval Select
bits : 20 - 21 (2 bit)
access : read-write

Enumeration:

0x00000000 : 8CYCLES

All channels with enabled refresh are refreshed every 8 prescaled cycles

0x00000001 : 16CYCLES

All channels with enabled refresh are refreshed every 16 prescaled cycles

0x00000002 : 32CYCLES

All channels with enabled refresh are refreshed every 32 prescaled cycles

0x00000003 : 64CYCLES

All channels with enabled refresh are refreshed every 64 prescaled cycles

End of enumeration elements list.


IEN

Interrupt Enable Register
address_offset : 0x10 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

IEN IEN read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 CH0 CH1 CH0UF CH1UF

CH0 : Channel 0 Conversion Complete Interrupt Enable
bits : 0 - 0 (1 bit)
access : read-write

CH1 : Channel 1 Conversion Complete Interrupt Enable
bits : 1 - 1 (1 bit)
access : read-write

CH0UF : Channel 0 Conversion Data Underflow Interrupt Enable
bits : 4 - 4 (1 bit)
access : read-write

CH1UF : Channel 1 Conversion Data Underflow Interrupt Enable
bits : 5 - 5 (1 bit)
access : read-write


IF

Interrupt Flag Register
address_offset : 0x14 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0

IF IF read-only 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 CH0 CH1 CH0UF CH1UF

CH0 : Channel 0 Conversion Complete Interrupt Flag
bits : 0 - 0 (1 bit)
access : read-only

CH1 : Channel 1 Conversion Complete Interrupt Flag
bits : 1 - 1 (1 bit)
access : read-only

CH0UF : Channel 0 Data Underflow Interrupt Flag
bits : 4 - 4 (1 bit)
access : read-only

CH1UF : Channel 1 Data Underflow Interrupt Flag
bits : 5 - 5 (1 bit)
access : read-only


IFS

Interrupt Flag Set Register
address_offset : 0x18 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0

IFS IFS write-only 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 CH0 CH1 CH0UF CH1UF

CH0 : Channel 0 Conversion Complete Interrupt Flag Set
bits : 0 - 0 (1 bit)
access : write-only

CH1 : Channel 1 Conversion Complete Interrupt Flag Set
bits : 1 - 1 (1 bit)
access : write-only

CH0UF : Channel 0 Data Underflow Interrupt Flag Set
bits : 4 - 4 (1 bit)
access : write-only

CH1UF : Channel 1 Data Underflow Interrupt Flag Set
bits : 5 - 5 (1 bit)
access : write-only


IFC

Interrupt Flag Clear Register
address_offset : 0x1C Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0

IFC IFC write-only 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 CH0 CH1 CH0UF CH1UF

CH0 : Channel 0 Conversion Complete Interrupt Flag Clear
bits : 0 - 0 (1 bit)
access : write-only

CH1 : Channel 1 Conversion Complete Interrupt Flag Clear
bits : 1 - 1 (1 bit)
access : write-only

CH0UF : Channel 0 Data Underflow Interrupt Flag Clear
bits : 4 - 4 (1 bit)
access : write-only

CH1UF : Channel 1 Data Underflow Interrupt Flag Clear
bits : 5 - 5 (1 bit)
access : write-only


CH0DATA

Channel 0 Data Register
address_offset : 0x20 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

CH0DATA CH0DATA read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 DATA

DATA : Channel 0 Data
bits : 0 - 11 (12 bit)
access : read-write


CH1DATA

Channel 1 Data Register
address_offset : 0x24 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

CH1DATA CH1DATA read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 DATA

DATA : Channel 1 Data
bits : 0 - 11 (12 bit)
access : read-write


COMBDATA

Combined Data Register
address_offset : 0x28 Bytes (0x0)
size : 32 bit
access : write-only
reset_value : 0x0
reset_Mask : 0x0

COMBDATA COMBDATA write-only 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 CH0DATA CH1DATA

CH0DATA : Channel 0 Data
bits : 0 - 11 (12 bit)
access : write-only

CH1DATA : Channel 1 Data
bits : 16 - 27 (12 bit)
access : write-only


CAL

Calibration Register
address_offset : 0x2C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

CAL CAL read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 CH0OFFSET CH1OFFSET GAIN

CH0OFFSET : Channel 0 Offset Calibration Value
bits : 0 - 5 (6 bit)
access : read-write

CH1OFFSET : Channel 1 Offset Calibration Value
bits : 8 - 13 (6 bit)
access : read-write

GAIN : Gain Calibration Value
bits : 16 - 22 (7 bit)
access : read-write


BIASPROG

Bias Programming Register
address_offset : 0x30 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

BIASPROG BIASPROG read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 BIASPROG HALFBIAS OPA2BIASPROG OPA2HALFBIAS

BIASPROG : Bias Programming Value
bits : 0 - 3 (4 bit)
access : read-write

HALFBIAS : Half Bias Current
bits : 6 - 6 (1 bit)
access : read-write

OPA2BIASPROG : Bias Programming Value for OPA2
bits : 8 - 11 (4 bit)
access : read-write

OPA2HALFBIAS : Half Bias Current
bits : 14 - 14 (1 bit)
access : read-write


STATUS

Status Register
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : read-only
reset_value : 0x0
reset_Mask : 0x0

STATUS STATUS read-only 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 CH0DV CH1DV

CH0DV : Channel 0 Data Valid
bits : 0 - 0 (1 bit)
access : read-only

CH1DV : Channel 1 Data Valid
bits : 1 - 1 (1 bit)
access : read-only


OPACTRL

Operational Amplifier Control Register
address_offset : 0x54 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

OPACTRL OPACTRL read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 OPA0EN OPA1EN OPA2EN OPA0HCMDIS OPA1HCMDIS OPA2HCMDIS OPA0LPFDIS OPA1LPFDIS OPA2LPFDIS OPA0SHORT OPA1SHORT OPA2SHORT

OPA0EN : OPA0 Enable
bits : 0 - 0 (1 bit)
access : read-write

OPA1EN : OPA1 Enable
bits : 1 - 1 (1 bit)
access : read-write

OPA2EN : OPA2 Enable
bits : 2 - 2 (1 bit)
access : read-write

OPA0HCMDIS : High Common Mode Disable.
bits : 6 - 6 (1 bit)
access : read-write

OPA1HCMDIS : High Common Mode Disable.
bits : 7 - 7 (1 bit)
access : read-write

OPA2HCMDIS : High Common Mode Disable.
bits : 8 - 8 (1 bit)
access : read-write

OPA0LPFDIS : Disables Low Pass Filter.
bits : 12 - 13 (2 bit)
access : read-write

Enumeration:

0x00000001 : PLPFDIS

Disables the LPF between positive pad and positive input.

0x00000002 : NLPFDIS

Disables the LPF between negative pad and negative input.

End of enumeration elements list.

OPA1LPFDIS : Disables Low Pass Filter.
bits : 14 - 15 (2 bit)
access : read-write

Enumeration:

0x00000001 : PLPFDIS

Disables the LPF between positive pad and positive input.

0x00000002 : NLPFDIS

Disables the LPF between negative pad and negative input.

End of enumeration elements list.

OPA2LPFDIS : Disables Low Pass Filter.
bits : 16 - 17 (2 bit)
access : read-write

Enumeration:

0x00000001 : PLPFDIS

Disables the LPF between positive pad and positive input.

0x00000002 : NLPFDIS

Disables the LPF between negative pad and negative input.

End of enumeration elements list.

OPA0SHORT : Short the non-inverting and inverting input.
bits : 22 - 22 (1 bit)
access : read-write

OPA1SHORT : Short the non-inverting and inverting input.
bits : 23 - 23 (1 bit)
access : read-write

OPA2SHORT : Short the non-inverting and inverting input.
bits : 24 - 24 (1 bit)
access : read-write


OPAOFFSET

Operational Amplifier Offset Register
address_offset : 0x58 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

OPAOFFSET OPAOFFSET read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 OPA2OFFSET

OPA2OFFSET : OPA2 Offset Configuration Value
bits : 0 - 5 (6 bit)
access : read-write


OPA0MUX

Operational Amplifier Mux Configuration Register
address_offset : 0x5C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

OPA0MUX OPA0MUX read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 POSSEL NEGSEL RESINMUX PPEN NPEN OUTPEN OUTMODE NEXTOUT RESSEL

POSSEL : OPA0 non-inverting Input Mux
bits : 0 - 2 (3 bit)
access : read-write

Enumeration:

0x00000000 : DISABLE

Input disabled

0x00000001 : DAC

DAC as input

0x00000002 : POSPAD

POS PAD as input

0x00000003 : OPA0INP

OPA0 as input

0x00000004 : OPATAP

OPA0 Resistor ladder as input

End of enumeration elements list.

NEGSEL : OPA0 inverting Input Mux
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0x00000000 : DISABLE

Input disabled

0x00000001 : UG

Unity Gain feedback path

0x00000002 : OPATAP

OPA0 Resistor ladder as input

0x00000003 : NEGPAD

Input from NEG PAD

End of enumeration elements list.

RESINMUX : OPA0 Resistor Ladder Input Mux
bits : 8 - 10 (3 bit)
access : read-write

Enumeration:

0x00000000 : DISABLE

Set for Unity Gain

0x00000001 : OPA0INP

Set for OPA0 input

0x00000002 : NEGPAD

NEG pad connected

0x00000003 : POSPAD

POS pad connected

0x00000004 : VSS

VSS connected

End of enumeration elements list.

PPEN : OPA0 Positive Pad Input Enable
bits : 12 - 12 (1 bit)
access : read-write

NPEN : OPA0 Negative Pad Input Enable
bits : 13 - 13 (1 bit)
access : read-write

OUTPEN : OPA0 Output Enable Value
bits : 14 - 18 (5 bit)
access : read-write

Enumeration:

0x00000001 : OUT0

Alternate Output 0

0x00000002 : OUT1

Alternate Output 1

0x00000004 : OUT2

Alternate Output 2

0x00000008 : OUT3

Alternate Output 3

0x00000010 : OUT4

Alternate Output 4

End of enumeration elements list.

OUTMODE : Output Select
bits : 22 - 23 (2 bit)
access : read-write

Enumeration:

0x00000000 : DISABLE

OPA0 output is disabled

0x00000001 : MAIN

Main OPA0 output to pin enabled

0x00000002 : ALT

OPA0 alternative output enabled.

0x00000003 : ALL

Main OPA0 output drives both main and alternative outputs.

End of enumeration elements list.

NEXTOUT : OPA0 Next Enable
bits : 26 - 26 (1 bit)
access : read-write

RESSEL : OPA0 Resistor Ladder Select
bits : 28 - 30 (3 bit)
access : read-write

Enumeration:

0x00000000 : RES0

Gain of 1/3

0x00000001 : RES1

Gain of 1

0x00000002 : RES2

Gain of 1 2/3

0x00000003 : RES3

Gain of 2

0x00000004 : RES4

Gain of 3

0x00000005 : RES5

Gain of 4 1/3

0x00000006 : RES6

Gain of 7

0x00000007 : RES7

Gain of 15

End of enumeration elements list.


OPA1MUX

Operational Amplifier Mux Configuration Register
address_offset : 0x60 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

OPA1MUX OPA1MUX read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 POSSEL NEGSEL RESINMUX PPEN NPEN OUTPEN OUTMODE NEXTOUT RESSEL

POSSEL : OPA1 non-inverting Input Mux
bits : 0 - 2 (3 bit)
access : read-write

Enumeration:

0x00000000 : DISABLE

Input disabled

0x00000001 : DAC

DAC as input

0x00000002 : POSPAD

POS PAD as input

0x00000003 : OPA0INP

OPA0 as input

0x00000004 : OPATAP

OPA 1 Resistor ladder as input

End of enumeration elements list.

NEGSEL : OPA1 inverting Input Mux
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0x00000000 : DISABLE

Input disabled

0x00000001 : UG

Unity Gain feedback path

0x00000002 : OPATAP

OPA1 Resistor ladder as input

0x00000003 : NEGPAD

Input from NEG PAD

End of enumeration elements list.

RESINMUX : OPA1 Resistor Ladder Input Mux
bits : 8 - 10 (3 bit)
access : read-write

Enumeration:

0x00000000 : DISABLE

Set for Unity Gain

0x00000001 : OPA0INP

Set for OPA0 input

0x00000002 : NEGPAD

NEG PAD connected

0x00000003 : POSPAD

POS PAD connected

0x00000004 : VSS

VSS connected

End of enumeration elements list.

PPEN : OPA1 Positive Pad Input Enable
bits : 12 - 12 (1 bit)
access : read-write

NPEN : OPA1 Negative Pad Input Enable
bits : 13 - 13 (1 bit)
access : read-write

OUTPEN : OPA1 Output Enable Value
bits : 14 - 18 (5 bit)
access : read-write

Enumeration:

0x00000001 : OUT0

Alternate Output 0

0x00000002 : OUT1

Alternate Output 1

0x00000004 : OUT2

Alternate Output 2

0x00000008 : OUT3

Alternate Output 3

0x00000010 : OUT4

Alternate Output 4

End of enumeration elements list.

OUTMODE : Output Select
bits : 22 - 23 (2 bit)
access : read-write

Enumeration:

0x00000000 : DISABLE

OPA0 output is disabled

0x00000001 : MAIN

Main OPA1 output to pin enabled

0x00000002 : ALT

OPA1 alternative output enabled.

0x00000003 : ALL

Main OPA1 output drives both main and alternative outputs.

End of enumeration elements list.

NEXTOUT : OPA1 Next Enable
bits : 26 - 26 (1 bit)
access : read-write

RESSEL : OPA1 Resistor Ladder Select
bits : 28 - 30 (3 bit)
access : read-write

Enumeration:

0x00000000 : RES0

Gain of 1/3

0x00000001 : RES1

Gain of 1

0x00000002 : RES2

Gain of 1 2/3

0x00000003 : RES3

Gain of 2

0x00000004 : RES4

Gain of 3

0x00000005 : RES5

Gain of 4 1/3

0x00000006 : RES6

Gain of 7

0x00000007 : RES7

Gain of 15

End of enumeration elements list.


OPA2MUX

Operational Amplifier Mux Configuration Register
address_offset : 0x64 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

OPA2MUX OPA2MUX read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 POSSEL NEGSEL RESINMUX PPEN NPEN OUTPEN OUTMODE NEXTOUT RESSEL

POSSEL : OPA2 non-inverting Input Mux
bits : 0 - 2 (3 bit)
access : read-write

Enumeration:

0x00000000 : DISABLE

Input disabled

0x00000002 : POSPAD

POS PAD as input

0x00000003 : OPA1INP

OPA1 as input

0x00000004 : OPATAP

OPA0 Resistor ladder as input

End of enumeration elements list.

NEGSEL : OPA2 inverting Input Mux
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

0x00000000 : DISABLE

Input disabled

0x00000001 : UG

Unity Gain feedback path

0x00000002 : OPATAP

OPA2 Resistor ladder as input

0x00000003 : NEGPAD

Input from NEG PAD

End of enumeration elements list.

RESINMUX : OPA2 Resistor Ladder Input Mux
bits : 8 - 10 (3 bit)
access : read-write

Enumeration:

0x00000000 : DISABLE

Set for Unity Gain

0x00000001 : OPA1INP

Set for OPA1 input

0x00000002 : NEGPAD

NEG PAD connected

0x00000003 : POSPAD

POS PAD connected

0x00000004 : VSS

VSS connected

End of enumeration elements list.

PPEN : OPA2 Positive Pad Input Enable
bits : 12 - 12 (1 bit)
access : read-write

NPEN : OPA2 Negative Pad Input Enable
bits : 13 - 13 (1 bit)
access : read-write

OUTPEN : OPA2 Output Location
bits : 14 - 15 (2 bit)
access : read-write

Enumeration:

0x00000001 : OUT0

Main Output 0

0x00000002 : OUT1

Main Output 1

End of enumeration elements list.

OUTMODE : Output Select
bits : 22 - 22 (1 bit)
access : read-write

NEXTOUT : OPA2 Next Enable
bits : 26 - 26 (1 bit)
access : read-write

RESSEL : OPA2 Resistor Ladder Select
bits : 28 - 30 (3 bit)
access : read-write

Enumeration:

0x00000000 : RES0

Gain of 1/3

0x00000001 : RES1

Gain of 1

0x00000002 : RES2

Gain of 1 2/3

0x00000003 : RES3

Gain of 2

0x00000004 : RES4

Gain of 3

0x00000005 : RES5

Gain of 4 1/3

0x00000006 : RES6

Gain of 7

0x00000007 : RES7

Gain of 15

End of enumeration elements list.


CH0CTRL

Channel 0 Control Register
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

CH0CTRL CH0CTRL read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 EN REFREN PRSEN PRSSEL

EN : Channel 0 Enable
bits : 0 - 0 (1 bit)
access : read-write

REFREN : Channel 0 Automatic Refresh Enable
bits : 1 - 1 (1 bit)
access : read-write

PRSEN : Channel 0 PRS Trigger Enable
bits : 2 - 2 (1 bit)
access : read-write

PRSSEL : Channel 0 PRS Trigger Select
bits : 4 - 7 (4 bit)
access : read-write

Enumeration:

0x00000000 : PRSCH0

PRS ch 0 triggers channel 0 conversion.

0x00000001 : PRSCH1

PRS ch 1 triggers channel 0 conversion.

0x00000002 : PRSCH2

PRS ch 2 triggers channel 0 conversion.

0x00000003 : PRSCH3

PRS ch 3 triggers channel 0 conversion.

0x00000004 : PRSCH4

PRS ch 4 triggers channel 0 conversion.

0x00000005 : PRSCH5

PRS ch 5 triggers channel 0 conversion.

0x00000006 : PRSCH6

PRS ch 6 triggers channel 0 conversion.

0x00000007 : PRSCH7

PRS ch 7 triggers channel 0 conversion.

0x00000008 : PRSCH8

PRS ch 8 triggers channel 0 conversion.

0x00000009 : PRSCH9

PRS ch 9 triggers channel 0 conversion.

0x0000000A : PRSCH10

PRS ch 10 triggers channel 0 conversion.

0x0000000B : PRSCH11

PRS ch 11 triggers channel 0 conversion.

End of enumeration elements list.


CH1CTRL

Channel 1 Control Register
address_offset : 0xC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0

CH1CTRL CH1CTRL read-write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Resets to Resets to 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 EN REFREN PRSEN PRSSEL

EN : Channel 1 Enable
bits : 0 - 0 (1 bit)
access : read-write

REFREN : Channel 1 Automatic Refresh Enable
bits : 1 - 1 (1 bit)
access : read-write

PRSEN : Channel 1 PRS Trigger Enable
bits : 2 - 2 (1 bit)
access : read-write

PRSSEL : Channel 1 PRS Trigger Select
bits : 4 - 7 (4 bit)
access : read-write

Enumeration:

0x00000000 : PRSCH0

PRS ch 0 triggers channel 1 conversion.

0x00000001 : PRSCH1

PRS ch 1 triggers channel 1 conversion.

0x00000002 : PRSCH2

PRS ch 2 triggers channel 1 conversion.

0x00000003 : PRSCH3

PRS ch 3 triggers channel 1 conversion.

0x00000004 : PRSCH4

PRS ch 4 triggers channel 1 conversion.

0x00000005 : PRSCH5

PRS ch 5 triggers channel 1 conversion.

0x00000006 : PRSCH6

PRS ch 6 triggers channel 1 conversion.

0x00000007 : PRSCH7

PRS ch 7 triggers channel 1 conversion.

0x00000008 : PRSCH8

PRS ch 8 triggers channel 1 conversion.

0x00000009 : PRSCH9

PRS ch 9 triggers channel 1 conversion.

0x0000000A : PRSCH10

PRS ch 10 triggers channel 1 conversion.

0x0000000B : PRSCH11

PRS ch 11 triggers channel 1 conversion.

End of enumeration elements list.



Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !

This website is sponsored by EmbeetleEmbeetle, an IDE designed from scratch for embedded software developers.