\n
address_offset : 0x0 Bytes (0x0)
size : 0x200 byte (0x0)
mem_usage : registers
protection : not protected
XOSC trimming register
address_offset : 0x118 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
Reserved1 : Do not change this value
bits : 0 - 3 (4 bit)
access : read-write
XO_FREQ_TUNE : Frequency tune value (eFuse)
bits : 4 - 14 (11 bit)
access : read-write
Reserved0 : Do not change this value
bits : 11 - 42 (32 bit)
access : read-write
OSC32K trimming register
address_offset : 0x11C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
Reserved0 : Do not change this value
bits : 0 - 15 (16 bit)
access : read-write
FREQTUNE_OSC32K : Freqency tune value. (eFuse)
bits : 16 - 36 (21 bit)
access : read-write
Sleep clock status
address_offset : 0x160 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SLPSLKTOGLE : Status toggling 1/2 of Sleep clock
bits : 0 - 0 (1 bit)
access : read-write
HL Status of Sleep Clock
address_offset : 0x164 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
SLPSLKHLSTATUS : Sleep Clock Status
bits : 0 - 0 (1 bit)
access : read-write
RTC wakeup config register
address_offset : 0x5C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RTCWAKEUPEN : RTC wakeup config. 1: Enable wakeup by RTC. 0: Disable wakeup by RTC
bits : 0 - 0 (1 bit)
access : read-write
GPIO input standby
address_offset : 0x78 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
GPIO0InputStandbyRelease : Input standby release on GPIO0. 1: Release standby. 0: Standby
bits : 0 - 0 (1 bit)
access : read-write
GPIO1InputStandbyRelease : Input standby release on GPIO1. 1: Release standby. 0: Standby
bits : 1 - 2 (2 bit)
access : read-write
GPIO2InputStandbyRelease : Input standby release on GPIO2. 1: Release standby. 0: Standby
bits : 2 - 4 (3 bit)
access : read-write
GPIO3InputStandbyRelease : Input standby release on GPIO3. 1: Release standby. 0: Standby
bits : 3 - 6 (4 bit)
access : read-write
GPIO4InputStandbyRelease : Input standby release on GPIO4. 1: Release standby. 0: Standby
bits : 4 - 8 (5 bit)
access : read-write
GPIO5InputStandbyRelease : Input standby release on GPIO5. 1: Release standby. 0: Standby
bits : 5 - 10 (6 bit)
access : read-write
GPIO6InputStandbyRelease : Input standby release on GPIO6. 1: Release standby. 0: Standby
bits : 6 - 12 (7 bit)
access : read-write
GPIO7InputStandbyRelease : Input standby release on GPIO7. 1: Release standby. 0: Standby
bits : 7 - 14 (8 bit)
access : read-write
GPIO8InputStandbyRelease : Input standby release on GPIO8. 1: Release standby. 0: Standby
bits : 8 - 16 (9 bit)
access : read-write
GPIO9InputStandbyRelease : Input standby release on GPIO9. 1: Release standby. 0: Standby
bits : 9 - 18 (10 bit)
access : read-write
GPIO10InputStandbyRelease : Input standby release on GPIO10. 1: Release standby. 0: Standby
bits : 10 - 20 (11 bit)
access : read-write
GPIO11InputStandbyRelease : Input standby release on GPIO11. 1: Release standby. 0: Standby
bits : 11 - 22 (12 bit)
access : read-write
GPIO12InputStandbyRelease : Input standby release on GPIO12. 1: Release standby. 0: Standby
bits : 12 - 24 (13 bit)
access : read-write
GPIO13InputStandbyRelease : Input standby release on GPIO13. 1: Release standby. 0: Standby
bits : 13 - 26 (14 bit)
access : read-write
GPIO14InputStandbyRelease : Input standby release on GPIO14. 1: Release standby. 0: Standby
bits : 14 - 28 (15 bit)
access : read-write
GPIO15InputStandbyRelease : Input standby release on GPIO15. 1: Release standby. 0: Standby
bits : 15 - 30 (16 bit)
access : read-write
GPIO16InputStandbyRelease : Input standby release on GPIO16. 1: Release standby. 0: Standby
bits : 16 - 32 (17 bit)
access : read-write
GPIO17InputStandbyRelease : Input standby release on GPIO17. 1: Release standby. 0: Standby
bits : 17 - 34 (18 bit)
access : read-write
RTC time register
address_offset : 0xB0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RTCSECONDSET : RTC time config of second. (Binary Coded Decimal). Min: 0. Max: 59
bits : 0 - 6 (7 bit)
access : read-write
RTCMINUTESET : RTC time config of minute. (Binary Coded Decimal). Min: 0. Max: 59
bits : 8 - 22 (15 bit)
access : read-write
RTCHOURSET : RTC time config of hour. (Binary Coded Decimal). Min: 0. Max: 23
bits : 16 - 37 (22 bit)
access : read-write
RTCDAYSET : RTC time config of day. (Binary Coded Decimal). Min=1. Max=31
bits : 24 - 53 (30 bit)
access : read-write
RTC date register
address_offset : 0xB4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RTCWEEK : RTC date config of week. (Binary Coded Decimal)
bits : 0 - 2 (3 bit)
access : read-write
RTCMONTH : RTC date config of month. (Binary Coded Decimal)
bits : 16 - 36 (21 bit)
access : read-write
RTCYEAR : RTC date config of year. (Binary Coded Decimal)
bits : 24 - 55 (32 bit)
access : read-write
RTC control config register
address_offset : 0xB8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PAGE : Set Page config. 0: Choose Page0. 1: Choose Page1
bits : 0 - 0 (1 bit)
access : read-write
ENAALM : Set alarm config. 0: Disable. 1: Enable
bits : 2 - 4 (3 bit)
access : read-write
ENATMR : Set clock config. 0: Disable. 1: Enable
bits : 3 - 6 (4 bit)
access : read-write
INTENA : Set interrupt config. 0: Disable. 1: Enable
bits : 7 - 14 (8 bit)
access : read-write
RTC reset register
address_offset : 0xBC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
Reserved1 : Do not change the values.
bits : 0 - 3 (4 bit)
access : read-write
RSTALM : Reset alarm. 0: Not reset. 1: Reset. If you wan to reset an alarm, please set 1 to this value and wait to become 0.
bits : 4 - 8 (5 bit)
access : read-write
RSTTMR : Reset clock. 0: Not reset. 1: Reset. If you wan to reset a clock, please set 1 to this value and wait to become 0.
bits : 5 - 10 (6 bit)
access : read-write
Reserved0 : Always set 0b0000_0000_1100_0001_0000_0000_11
bits : 6 - 37 (32 bit)
access : read-write
RTC time register2
address_offset : 0xC4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RTCMINUTESET : RTC time config of minute. (Binary Coded Decimal). Min: 0. Max: 59
bits : 8 - 22 (15 bit)
access : read-write
RTCHOURSET : RTC time config of hour. (Binary Coded Decimal). Min: 0. Max: 23
bits : 16 - 37 (22 bit)
access : read-write
RTCDAYSET : RTC time config of day. (Binary Coded Decimal). Min: 1. Max: 31
bits : 24 - 53 (30 bit)
access : read-write
RTC Adjust 1 Sec register
address_offset : 0xCC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
Reserved1 : Reserved (Set 0 to all the bits)
bits : 0 - 7 (8 bit)
access : read-write
SCUT : 1Hz Short Cut
bits : 8 - 16 (9 bit)
access : read-write
RTC interrupt clear register
address_offset : 0xD0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RTCINTclr : Clear RTC interrupt. 1: Clear. 0: Don't care
bits : 0 - 0 (1 bit)
access : read-write
RTC interrupt enable register
address_offset : 0xD4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RTCINTEN : Enable RTC interrupt. 1: Enable interrupt request. 0: Disable interrupt request
bits : 0 - 0 (1 bit)
access : read-write
RTC count cnofig register
address_offset : 0xD8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RTCNTCFG : Set RTC config. 1: Enable RTC config. 0: Disable RTC config
bits : 0 - 0 (1 bit)
access : read-write
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.