ADC_ADDR0 (ADDR0)

ADC_ADDR4 (ADDR4)

ADC_ADPDMA (ADPDMA)

ADC_ADDR5 (ADDR5)

ADC_ADDR6 (ADDR6)

ADC_ADDR7 (ADDR7)

ADC_ADDR1 (ADDR1)

ADC_ADDR29 (ADDR29)

ADC_ADDR30 (ADDR30)

ADC_ADDR2 (ADDR2)

ADC_ADCR (ADCR)

ADC_ADCHER (ADCHER)

ADC_ADCMPR0 (ADCMPR0)

ADC_ADCMPR1 (ADCMPR1)

ADC_ADSR0 (ADSR0)

ADC_ADSR1 (ADSR1)

ADC_ADSR2 (ADSR2)

ADC_ADTDCR (ADTDCR)

ADC_ADDR3 (ADDR3)

RSLT : A/D Conversion Result (Read Only) This field contains conversion result of ADC.
bits : 0 - 15 (16 bit)
access : read-only

OVERRUN : Overrun Flag (Read Only) If converted data in RSLT bits has not been read before new conversion result is loaded to this register, OVERRUN bit is set to 1. It is cleared by hardware after ADC_ADDR register is read.
bits : 16 - 16 (1 bit)
access : read-only

Enumeration:

End of enumeration elements list.

VALID : Valid Flag (Read Only) This bit will be set to 1 when the conversion of the corresponding channel is completed. This bit will be cleared to 0 by hardware after ADC_ADDR register is read.
bits : 17 - 17 (1 bit)
access : read-only

Enumeration:

End of enumeration elements list.

CURDAT : ADC PDMA Current Transfer Data Register (Read Only) When PDMA transferring, reading this register can monitor current PDMA transfer data. The current PDMA transfer data could be the content of ADC_ADDR0 ~ ADC_ADDR7 and ADC_ADDR29 ~ ADC_ADDR30 registers.
bits : 0 - 17 (18 bit)
access : read-only

ADEN : A/D Converter Enable Bit Note: Before starting A/D conversion function, this bit should be set to 1. Clear it to 0 to disable A/D converter analog circuit to save power consumption.
bits : 0 - 0 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

ADIE : A/D Interrupt Enable Bit A/D conversion end interrupt request is generated if ADIE bit is set to 1.
bits : 1 - 1 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

ADMD : A/D Converter Operation Mode Control Note 1: When changing the operation mode, software should clear ADST bit first. Note 2: In Burst mode, the A/D result data is always at ADC Data Register 0.
bits : 2 - 3 (2 bit)
access : read-write

Enumeration:

End of enumeration elements list.

TRGS : Hardware Trigger Source Note: Software should clear TRGEN bit and ADST bit to 0 before changing TRGS bits.
bits : 4 - 5 (2 bit)
access : read-write

Enumeration:

End of enumeration elements list.

TRGCOND : External Trigger Condition These two bits decide external pin STADC trigger event is level or edge. The signal must be kept at stable state at least 8 PCLKs for level trigger. If edge trigger condition is selected, the STADC pin must be kept original state at least 4 PCLKs, and the state after edge transition also must be kept at least 4 PCLKs.
bits : 6 - 7 (2 bit)
access : read-write

Enumeration:

End of enumeration elements list.

TRGEN : External Trigger Enable Bit Enable or disable triggering of A/D conversion by external STADC pin, PWM trigger and Timer trigger. If external trigger is enabled, the ADST bit can be set to 1 by the selected hardware trigger source. Note: The ADC external trigger function is only supported in Single-cycle Scan mode.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

PTEN : PDMA Transfer Enable Bit When A/D conversion is completed, the converted data is loaded into ADC_ADDR0~7, ADC_ADDR29~ADC_ADDR30 registers. Software can enable this bit to generate a PDMA data transfer request.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

DIFFEN : Differential Input Mode Control Note 1: In Differential Input mode, only the even number of the two corresponding channels needs to be enabled in ADC_ADCHER register. The conversion result will be placed to the corresponding data register of the enabled channel.
bits : 10 - 10 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

ADST : A/D Conversion Start ADST bit can be set to 1 from four sources: software, external pin STADC, PWM trigger and Timer trigger. ADST bit will be cleared to 0 by hardware automatically at the ends of Single mode and Single-cycle Scan mode. In Continuous Scan mode and Burst mode, A/D conversion is continuously performed until software writes 0 to this bit or chip is reset.
bits : 11 - 11 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

SMPTSEL : ADC Internal Sampling Time Selection
bits : 16 - 18 (3 bit)
access : read-write

Enumeration:

End of enumeration elements list.

DMOF : Differential Input Mode Output Format If user enables differential input mode, the conversion result can be expressed with binary straight format (unsigned format) or 2's complement format (signed format).
bits : 31 - 31 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CHEN : Analog Input Channel Enable Control Set ADC_ADCHER[7:0] bits to enable the corresponding analog input channel 7 ~ 0. If DIFFEN (ADC_ADCR[10]) bit is set to 1, only the even number channel needs to be enabled. Besides, setting ADC_ADCHER[29] to ADC_ADCHER[30] bits will enable internal channel for band-gap voltage and temperature sensor respectively. Other bits are reserved. Note 1: If the internal channel for band-gap voltage (CHEN[29]) is active, the maximum sampling rate will be 300 KSPS. Note 2: If the internal channel for temperature sensor (CHEN[30]) is active, the maximum sampling rate will be 300 KSPS.
bits : 0 - 31 (32 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CMPEN : Compare Enable Bit Set this bit to 1 to enable ADC controller to compare CMPD with specified channel conversion result when converted data is loaded into ADC_ADDRx register.
bits : 0 - 0 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CMPIE : Compare Interrupt Enable Bit
bits : 1 - 1 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CMPCOND : Compare Condition
bits : 2 - 2 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CMPCH : Compare Channel Selection
bits : 3 - 7 (5 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CMPMATCNT : Compare Match Count
bits : 8 - 11 (4 bit)
access : read-write

CMPWEN : Compare Window Mode Enable Bit Note: This bit is only presented in ADC_ADCMPR0 register.
bits : 15 - 15 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CMPD : Comparison Data The 12-bit data is used to compare with conversion result of specified channel. Note: CMPD bits should be filled in unsigned format (straight binary format).
bits : 16 - 27 (12 bit)
access : read-write

ADF : A/D Conversion End Flag A status flag that indicates the end of A/D conversion. Software can write 1 to clear this bit. ADF bit is set to 1 at the following three conditions: When A/D conversion ends in Single mode. When A/D conversion ends on all specified channels in Single-cycle Scan mode and Continuous Scan mode. When more than or equal to 9 data in FIFO in Burst mode.
bits : 0 - 0 (1 bit)
access : read-write

CMPF0 : Compare Flag 0 When the A/D conversion result of the selected channel meets setting condition in ADC_ADCMPR0 register then this bit is set to 1. This bit is cleared by writing 1 to it.
bits : 1 - 1 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

CMPF1 : Compare Flag 1 When the A/D conversion result of the selected channel meets setting condition in ADC_ADCMPR1 register then this bit is set to 1 it is cleared by writing 1 to it
bits : 2 - 2 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

BUSY : BUSY/IDLE (Read Only) This bit is a mirror of ADST bit in ADC_ADCR register.
bits : 7 - 7 (1 bit)
access : read-only

Enumeration:

End of enumeration elements list.

VALIDF : Data Valid Flag (Read Only) If any of VALID (ADC_ADDRx[17]) is set, this flag will be set to 1. Note: When ADC is in burst mode and any conversion result is valid, this flag will be set to 1.
bits : 8 - 8 (1 bit)
access : read-only

OVERRUNF : Overrun Flag (Read Only) If any of OVERRUN (ADC_ADDRx[16]) is set, this flag will be set to 1. Note: When ADC is in burst mode and the FIFO is overrun, this flag will be set to 1.
bits : 16 - 16 (1 bit)
access : read-only

CHANNEL : Current Conversion Channel (Read Only)
bits : 27 - 31 (5 bit)
access : read-only

VALID : Data Valid Flag (Read Only) VALID[30:29], VALID[7:0] are the mirror of the VALID bits in ADC_ADDR30[17] ~ ADC_ADDR29[17], ADC_ADDR7[17]~ ADC_ADDR0[17]. The other bits are reserved. Note: When ADC is in burst mode and any conversion result is valid, VALID[30:29], VALID[7:0] will be set to 1.
bits : 0 - 31 (32 bit)
access : read-only

OVERRUN : Overrun Flag (Read Only) OVERRUN[30:29], VALID[7:0] are the mirror of the OVERRUN bit in ADC_ADDR30[16] ~ADC_ADDR29[16], ADC_ADDR7[16] ~ ADC_ADDR0[16]. The other bits are reserved. Note: When ADC is in burst mode and the FIFO is overrun, OVERRUN[30:29], OVERRUN[7:0] will be set to 1.
bits : 0 - 31 (32 bit)
access : read-only

PTDT : BPWM Trigger Delay Time Set this field will delay ADC start conversion time after BPWM trigger. BPWM trigger delay time is (4 * PTDT) * system clock
bits : 0 - 7 (8 bit)
access : read-write