\n
address_offset : 0x0 Bytes (0x0)
size : 0xE4 byte (0x0)
mem_usage : registers
protection :
Rewriting Enable Register
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
FEWEN : Setup enable/disable the flash memory to be rewritten
bits : 0 - 7 (8 bit)
access : read-write
KEY_CODE : Register Key
bits : 8 - 23 (16 bit)
access : write
__reserve0 : 0 is always read out.
bits : 16 - 47 (32 bit)
access : read
Writing Data Register 0
address_offset : 0x10 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
WDATA0 : Set the data to be written to the flash memory. This is the lower 4 bytes of the data to be rewritten (8 bytes).
bits : 0 - 31 (32 bit)
access : read-write
Writing Data Register 1
address_offset : 0x14 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
WDATA1 : Set the data to be written to the flash memory. This is the upper 4 bytes of the data to be rewritten (8 bytes).
bits : 0 - 31 (32 bit)
access : read-write
SW Protect Start Address
address_offset : 0x18 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
SPROSTR : SW protect start address
bits : 0 - 31 (32 bit)
access : read-write
SW Protect End Address
address_offset : 0x1C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
SPROEND : SW protect end address
bits : 0 - 31 (32 bit)
access : read-write
I-Flash HW Protect 0 Start Address
address_offset : 0x20 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
HPRO0STRI : I-Flash HW protect 0 start address
bits : 0 - 31 (32 bit)
access : read
I-Flash HW Protect 0 End Address
address_offset : 0x24 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
HPRO0ENDI : I-Flash HW protect 0 end address
bits : 0 - 31 (32 bit)
access : read
I-Flash HW Protect 1 Start Address
address_offset : 0x28 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
HPRO1STRI : I-Flash HW protect 1 start address
bits : 0 - 31 (32 bit)
access : read
I-Flash HW Protect 1 End Address
address_offset : 0x2C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
HPRO1ENDI : I-Flash HW protect 1 end address
bits : 0 - 31 (32 bit)
access : read
D-Flash HW Protect 0 Start Address
address_offset : 0x30 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
HPRO0STRD : D-Flash HW protect 0 start address
bits : 0 - 31 (32 bit)
access : read
D-Flash HW Protect 0 End Address
address_offset : 0x34 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
HPRO0ENDD : D-Flash HW protect 0 end address
bits : 0 - 31 (32 bit)
access : read
D-Flash HW Protect 1 Start Address
address_offset : 0x38 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
HPRO1STRD : D-Flash HW protect 1 start address
bits : 0 - 31 (32 bit)
access : read
D-Flash HW Protect 1 End Address
address_offset : 0x3C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
HPRO1ENDD : D-Flash HW protect 1 end address
bits : 0 - 31 (32 bit)
access : read
Rewriting Start Register
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
START : Start Program/Erase function
bits : 0 - 0 (1 bit)
access : read-write
ERASEMD : Select Program/Erase function
bits : 1 - 2 (2 bit)
access : read-write
__reserve0 : 0 is always read out.
bits : 2 - 33 (32 bit)
access : read
Rewriting Status Register
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
WBUSY : Rewriting execution flag
bits : 0 - 0 (1 bit)
access : read
__reserve0 : Undefined value will be read
bits : 1 - 3 (3 bit)
access : read
__reserve1 : 0 is always read out.
bits : 3 - 10 (8 bit)
access : read
NBRANK : Writing blank error flag
bits : 8 - 16 (9 bit)
access : read
OUTADR : Rewriting address error flag
bits : 9 - 18 (10 bit)
access : read
SPRO : Rewriting SW protect error flag
bits : 10 - 20 (11 bit)
access : read
HPROI0 : I-Flash HW protect 0 error flag
bits : 11 - 22 (12 bit)
access : read
HPROI1 : I-Flash HW protect 1 error flag
bits : 12 - 24 (13 bit)
access : read
HPROD0 : D-Flash HW protect 0 error flag
bits : 13 - 26 (14 bit)
access : read
HPROD1 : D-Flash HW protect 1 error flag
bits : 14 - 28 (15 bit)
access : read
__reserve2 : 0 is always read out.
bits : 15 - 30 (16 bit)
access : read
__reserve3 : 0 is always read out.
bits : 16 - 47 (32 bit)
access : read
I-Flash ECC Control Register
address_offset : 0x80 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
ECCMOD : I-Flash ECC enable
bits : 0 - 0 (1 bit)
access : read-write
__reserve0 : This bit must be set to 0 .
bits : 1 - 2 (2 bit)
access : read-write
__reserve1 : 0 is always read out.
bits : 2 - 9 (8 bit)
access : read
KEY_CODE : Register Key
bits : 8 - 23 (16 bit)
access : read-write
__reserve2 : 0 is always read out.
bits : 16 - 47 (32 bit)
access : read
I-Flash 1-bit Error Address
address_offset : 0x88 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
SBEA : I-Flash ECC 1-bit error interrupt target address
bits : 0 - 31 (32 bit)
access : read
I-Flash 1-bit Error Detection Register
address_offset : 0x8C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
SBDET : I-Flash ECC 1-bit error interrupt target address
bits : 0 - 0 (1 bit)
access : read
__reserve0 : 0 is always read out.
bits : 1 - 8 (8 bit)
access : read
SBMASTER : I-Flash ECC 1-bit error interrupt generation master information
bits : 8 - 19 (12 bit)
access : read
__reserve1 : 0 is always read out.
bits : 12 - 43 (32 bit)
access : read
I-Flash 1-bit Error Interrupt Clear Register
address_offset : 0x90 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
SBECLRI : [Write]
bits : 0 - 0 (1 bit)
access : read-write
__reserve0 : 0 is always read out.
bits : 1 - 32 (32 bit)
access : read
I-Flash 2-bit or more Error Address
address_offset : 0x94 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
MBEA : I-Flash ECC 2-bit error interrupt target address
bits : 0 - 31 (32 bit)
access : read
I-Flash 2-bit or more Error Detection Register
address_offset : 0x98 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
MBDET : I-Flash ECC 2-bit error interrupt target address
bits : 0 - 0 (1 bit)
access : read
__reserve0 : 0 is always read out.
bits : 1 - 8 (8 bit)
access : read
MBMASTER : I-Flash ECC 2-bit error interrupt generation master information
bits : 8 - 19 (12 bit)
access : read
__reserve1 : 0 is always read out.
bits : 12 - 43 (32 bit)
access : read
I-Flash 2-bit or more Error Interrupt Clear Register
address_offset : 0x9C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
MBECLRI : [Write]
bits : 0 - 0 (1 bit)
access : read-write
__reserve0 : 0 is always read out.
bits : 1 - 32 (32 bit)
access : read
I-Flash Access Wait Control Register
address_offset : 0xA0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
WAITREG : I-Flash Read access wait setting
bits : 0 - 3 (4 bit)
access : read-write
__reserve0 : 0 is always read out.
bits : 4 - 11 (8 bit)
access : read
KEY_CODE : Register Key
bits : 8 - 23 (16 bit)
access : read-write
__reserve1 : 0 is always read out.
bits : 16 - 47 (32 bit)
access : read
I-Flash Debug Access Error Detection Register
address_offset : 0xA8 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
DBGSDET : I-Flash 1-bit error detection at debugger access
bits : 0 - 0 (1 bit)
access : read
DBGMDET : I-Flash 2-bit or more error detection at debugger access
bits : 1 - 2 (2 bit)
access : read
__reserve0 : 0 is always read out.
bits : 2 - 9 (8 bit)
access : read
I-Flash Debug Access Error Detection Clear Register
address_offset : 0xAC Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
DBGSCLR : I-Flash 1-bit error detection at debugger access clear
bits : 0 - 0 (1 bit)
access : read-write
DBGMCLR : I-Flash 2-bit or more error detection at debugger access clear
bits : 1 - 2 (2 bit)
access : read-write
__reserve0 : 0 is always read out.
bits : 2 - 9 (8 bit)
access : read
D-Flash ECC Control Register
address_offset : 0xB0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
ECCMOD : D-Flash ECC enable
bits : 0 - 0 (1 bit)
access : read-write
__reserve0 : This bit must be set to 0 .
bits : 1 - 2 (2 bit)
access : read-write
__reserve1 : 0 is always read out.
bits : 2 - 9 (8 bit)
access : read
KEY_CODE : Register Key
bits : 8 - 23 (16 bit)
access : read-write
__reserve2 : 0 is always read out.
bits : 16 - 47 (32 bit)
access : read
D-Flash 1-bit Error Address
address_offset : 0xB8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
SBEA : D-Flash ECC 1-bit error interrupt target address
bits : 0 - 31 (32 bit)
access : read
D-Flash 1-bit Error Detection Register
address_offset : 0xBC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
SBDET : D-Flash ECC 1-bit error interrupt target address
bits : 0 - 0 (1 bit)
access : read
__reserve0 : 0 is always read out.
bits : 1 - 8 (8 bit)
access : read
SBMASTER : D-Flash ECC 1-bit error interrupt generation master information
bits : 8 - 19 (12 bit)
access : read
__reserve1 : 0 is always read out.
bits : 12 - 43 (32 bit)
access : read
Rewriting Destination Address Register
address_offset : 0xC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
PEADR : Rewriting (write/erase) address
bits : 0 - 31 (32 bit)
access : read-write
D-Flash 1-bit Error Interrupt Clear Register
address_offset : 0xC0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
SBECLRI : [Write]
bits : 0 - 0 (1 bit)
access : read-write
__reserve0 : 0 is always read out.
bits : 1 - 32 (32 bit)
access : read
D-Flash 2-bit or more Error Address
address_offset : 0xC4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
MBEA : D-Flash ECC 2-bit error interrupt target address
bits : 0 - 31 (32 bit)
access : read
D-Flash 2-bit or more Error Detection Register
address_offset : 0xC8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
MBDET : D-Flash ECC 2-bit error interrupt target address
bits : 0 - 0 (1 bit)
access : read
__reserve0 : 0 is always read out.
bits : 1 - 8 (8 bit)
access : read
MBMASTER : D-Flash ECC 2-bit error interrupt generation master information
bits : 8 - 19 (12 bit)
access : read
__reserve1 : 0 is always read out.
bits : 12 - 43 (32 bit)
access : read
D-Flash 2-bit or more Error Interrupt Clear Register
address_offset : 0xCC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
MBECLRI : [Write]
bits : 0 - 0 (1 bit)
access : read-write
__reserve0 : 0 is always read out.
bits : 1 - 32 (32 bit)
access : read
D-Flash Access Wait Control Register
address_offset : 0xD0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
WAITREG : D-Flash Read access wait setting
bits : 0 - 3 (4 bit)
access : read-write
__reserve0 : 0 is always read out.
bits : 4 - 11 (8 bit)
access : read
KEY_CODE : Register Key
bits : 8 - 23 (16 bit)
access : read-write
__reserve1 : 0 is always read out.
bits : 16 - 47 (32 bit)
access : read
D-Flash Debug Access Error Detection Register
address_offset : 0xD8 Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
DBGSDET : D-Flash 1-bit error detection at debugger access
bits : 0 - 0 (1 bit)
access : read
DBGMDET : D-Flash 2-bit or more error detection at debugger access
bits : 1 - 2 (2 bit)
access : read
__reserve0 : 0 is always read out.
bits : 2 - 9 (8 bit)
access : read
D-Flash Debug Access Error Detection Clear Register
address_offset : 0xDC Bytes (0x0)
size : 8 bit
access : read-write
reset_value : 0x0
DBGSCLR : D-Flash 1-bit error detection at debugger access clear
bits : 0 - 0 (1 bit)
access : read-write
DBGMCLR : D-Flash 2-bit or more error detection at debugger access clear
bits : 1 - 2 (2 bit)
access : read-write
__reserve0 : 0 is always read out.
bits : 2 - 9 (8 bit)
access : read
Swap Switching Register
address_offset : 0xE0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
NSWAPON : Boot sector swap setting
bits : 0 - 0 (1 bit)
access : read-write
__reserve0 : 0 is always read out.
bits : 1 - 8 (8 bit)
access : read
KEY_CODE : Register Key
bits : 8 - 23 (16 bit)
access : read-write
__reserve1 : 0 is always read out.
bits : 16 - 47 (32 bit)
access : read
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.