\n
address_offset : 0x0 Bytes (0x0)
size : 0x48 byte (0x0)
mem_usage : registers
protection :
Comparator 0 Co0trol Register
address_offset : 0x0 Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
EN : Start of the comparator comparison
bits : 0 - 0 (1 bit)
access : read-write
MD : Operation mode setting
bits : 1 - 2 (2 bit)
access : read-write
PW0 : Operation of the CMPn0 comparator
bits : 2 - 4 (3 bit)
access : read-write
PW1 : Operation of the CMPn1 comparator
bits : 3 - 6 (4 bit)
access : read-write
INV0 : Selection of CMPn0 comparator detection polarity
bits : 4 - 8 (5 bit)
access : read-write
INV1 : Selection of CMPn1 comparator detection polarity
bits : 5 - 10 (6 bit)
access : read-write
HYS0 : CMPn0 hysteresis setting
bits : 6 - 12 (7 bit)
access : read-write
HYS1 : CMPn1 hysteresis setting
bits : 7 - 14 (8 bit)
access : read-write
NF : Selection of comparator output noise filter
bits : 8 - 19 (12 bit)
access : read-write
__reserve0 : 0 is always read out.
bits : 12 - 27 (16 bit)
access : read
Comparator 1 Co1trol Register
address_offset : 0x10 Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
EN : Start of the comparator comparison
bits : 0 - 0 (1 bit)
access : read-write
MD : Operation mode setting
bits : 1 - 2 (2 bit)
access : read-write
PW0 : Operation of the CMPn0 comparator
bits : 2 - 4 (3 bit)
access : read-write
PW1 : Operation of the CMPn1 comparator
bits : 3 - 6 (4 bit)
access : read-write
INV0 : Selection of CMPn0 comparator detection polarity
bits : 4 - 8 (5 bit)
access : read-write
INV1 : Selection of CMPn1 comparator detection polarity
bits : 5 - 10 (6 bit)
access : read-write
HYS0 : CMPn0 hysteresis setting
bits : 6 - 12 (7 bit)
access : read-write
HYS1 : CMPn1 hysteresis setting
bits : 7 - 14 (8 bit)
access : read-write
NF : Selection of comparator output noise filter
bits : 8 - 19 (12 bit)
access : read-write
__reserve0 : 0 is always read out.
bits : 12 - 27 (16 bit)
access : read
Comparator 1 Status Register
address_offset : 0x14 Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
STR0 : Detection state of CMPn0
bits : 0 - 0 (1 bit)
access : read
STR1 : Detection state of CMPn1
bits : 1 - 2 (2 bit)
access : read
__reserve0 : 0 is always read out.
bits : 2 - 17 (16 bit)
access : read
Comparator 2 Co2trol Register
address_offset : 0x20 Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
EN : Start of the comparator comparison
bits : 0 - 0 (1 bit)
access : read-write
MD : Operation mode setting
bits : 1 - 2 (2 bit)
access : read-write
PW0 : Operation of the CMPn0 comparator
bits : 2 - 4 (3 bit)
access : read-write
PW1 : Operation of the CMPn1 comparator
bits : 3 - 6 (4 bit)
access : read-write
INV0 : Selection of CMPn0 comparator detection polarity
bits : 4 - 8 (5 bit)
access : read-write
INV1 : Selection of CMPn1 comparator detection polarity
bits : 5 - 10 (6 bit)
access : read-write
HYS0 : CMPn0 hysteresis setting
bits : 6 - 12 (7 bit)
access : read-write
HYS1 : CMPn1 hysteresis setting
bits : 7 - 14 (8 bit)
access : read-write
NF : Selection of comparator output noise filter
bits : 8 - 19 (12 bit)
access : read-write
__reserve0 : 0 is always read out.
bits : 12 - 27 (16 bit)
access : read
Comparator 2 Status Register
address_offset : 0x24 Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
STR0 : Detection state of CMPn0
bits : 0 - 0 (1 bit)
access : read
STR1 : Detection state of CMPn1
bits : 1 - 2 (2 bit)
access : read
__reserve0 : 0 is always read out.
bits : 2 - 17 (16 bit)
access : read
Comparator 3 Co3trol Register
address_offset : 0x30 Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
EN : Start of the comparator comparison
bits : 0 - 0 (1 bit)
access : read-write
MD : Operation mode setting
bits : 1 - 2 (2 bit)
access : read-write
PW0 : Operation of the CMPn0 comparator
bits : 2 - 4 (3 bit)
access : read-write
PW1 : Operation of the CMPn1 comparator
bits : 3 - 6 (4 bit)
access : read-write
INV0 : Selection of CMPn0 comparator detection polarity
bits : 4 - 8 (5 bit)
access : read-write
INV1 : Selection of CMPn1 comparator detection polarity
bits : 5 - 10 (6 bit)
access : read-write
HYS0 : CMPn0 hysteresis setting
bits : 6 - 12 (7 bit)
access : read-write
HYS1 : CMPn1 hysteresis setting
bits : 7 - 14 (8 bit)
access : read-write
NF : Selection of comparator output noise filter
bits : 8 - 19 (12 bit)
access : read-write
__reserve0 : 0 is always read out.
bits : 12 - 27 (16 bit)
access : read
Comparator 3 Status Register
address_offset : 0x34 Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
STR0 : Detection state of CMPn0
bits : 0 - 0 (1 bit)
access : read
STR1 : Detection state of CMPn1
bits : 1 - 2 (2 bit)
access : read
__reserve0 : 0 is always read out.
bits : 2 - 17 (16 bit)
access : read
Comparator 0 Status Register
address_offset : 0x4 Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
STR0 : Detection state of CMPn0
bits : 0 - 0 (1 bit)
access : read
STR1 : Detection state of CMPn1
bits : 1 - 2 (2 bit)
access : read
__reserve0 : 0 is always read out.
bits : 2 - 17 (16 bit)
access : read
Comparator 4 Co4trol Register
address_offset : 0x40 Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
EN : Start of the comparator comparison
bits : 0 - 0 (1 bit)
access : read-write
MD : Operation mode setting
bits : 1 - 2 (2 bit)
access : read-write
PW0 : Operation of the CMPn0 comparator
bits : 2 - 4 (3 bit)
access : read-write
PW1 : Operation of the CMPn1 comparator
bits : 3 - 6 (4 bit)
access : read-write
INV0 : Selection of CMPn0 comparator detection polarity
bits : 4 - 8 (5 bit)
access : read-write
INV1 : Selection of CMPn1 comparator detection polarity
bits : 5 - 10 (6 bit)
access : read-write
HYS0 : CMPn0 hysteresis setting
bits : 6 - 12 (7 bit)
access : read-write
HYS1 : CMPn1 hysteresis setting
bits : 7 - 14 (8 bit)
access : read-write
NF : Selection of comparator output noise filter
bits : 8 - 19 (12 bit)
access : read-write
__reserve0 : 0 is always read out.
bits : 12 - 27 (16 bit)
access : read
Comparator 4 Status Register
address_offset : 0x44 Bytes (0x0)
size : 16 bit
access : read-write
reset_value : 0x0
STR0 : Detection state of CMPn0
bits : 0 - 0 (1 bit)
access : read
STR1 : Detection state of CMPn1
bits : 1 - 2 (2 bit)
access : read
__reserve0 : 0 is always read out.
bits : 2 - 17 (16 bit)
access : read
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.