\n
address_offset : 0x0 Bytes (0x0)
size : 0x14 byte (0x0)
mem_usage : registers
protection :
Brown Out Detector Select Register
address_offset : 0x0 Bytes (0x0)
size : -1 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BODVL : BOD Voltage Level
111b aaa 4.6V
110b aaa 3.0V
101b aaa 2.8V
100b aaa 2.625V
011b aaa 2.5V
010b aaa 2.4V
001b aaa 2.2V
000b aaa 2.1V
bits : 0 - 2 (3 bit)
access : read-write
BODHYS : BOD Hysteresis
bits : 3 - 3 (1 bit)
access : read-write
Enumeration:
#0 : 0
Hysteresis Disabled
#1 : 1
Enable Hysteresis of BOD detection
End of enumeration elements list.
Brown Out Detector Timer Register
address_offset : 0x10 Bytes (0x0)
size : -1 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DURTOFF : Time BOD Detector Is Off
(DURTOFF+1)*100us . Minimum value is 7. (default is 99.6ms)
bits : 0 - 15 (16 bit)
access : read-write
DURTON : Time BOD Detector Is Active
(DURTON+1) * 100us. Minimum value is 1. (default is 400us)
bits : 16 - 19 (4 bit)
access : read-write
Brown Out Detector Enable Register
address_offset : 0x4 Bytes (0x0)
size : -1 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BODEN : BOD Enable
1xb aaa Enable continuous BOD detection.
01b aaa Enable time multiplexed BOD detection. See BODTALM_BODDTMR register.
00b aaa Disable BOD Detection.
bits : 0 - 1 (2 bit)
access : read-write
BODINTEN : BOD Interrupt Enable
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disable BOD Interrupt
#1 : 1
Enable BOD Interrupt
End of enumeration elements list.
BODIF : Current Status Of Interrupt
Latched whenever a BOD event occurs and BODINTEN aaa 1. Write '1' to clear.
bits : 3 - 3 (1 bit)
access : read-write
BODOUT : Output of BOD Detection Block
This signal can be monitored to determine the current state of the BOD comparator. Read '1' implies that VCC is less than BODVL.
bits : 4 - 4 (1 bit)
access : read-write
Temperature Alarm Select Register
address_offset : 0x8 Bytes (0x0)
size : -1 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TALMVL : Temperature Alarm Sense Level
0000:105C
0001:115C
0010:125C
0100:135C
1000:145C
bits : 0 - 3 (4 bit)
access : read-write
Temperature Alarm Enable Register
address_offset : 0xC Bytes (0x0)
size : -1 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
TALMEN : TALARM Enable
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disable TALARM Detection
#1 : 1
Enable TALARM Detection
End of enumeration elements list.
TALMOUT : Output of TALARM Block
Can be polled to determine whether TALARM active (be 1).
bits : 1 - 1 (1 bit)
access : read-write
TALMIEN : TALARM Interrupt Enable
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disable TALARM Interrupt
#1 : 1
Enable TALARM Interrupt
End of enumeration elements list.
TALMIF : Current status of interrupt
Latched whenever a Temperature Sense event occurs and IE aaa 1. Write '1' to clear.
bits : 3 - 3 (1 bit)
access : read-write
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.