\n
address_offset : 0x0 Bytes (0x0)
size : 0x8 byte (0x0)
mem_usage : registers
protection :
address_offset : 0x10 Bytes (0x0)
size : 0x4 byte (0x0)
mem_usage : registers
protection :
Brown Out Detector Select Register
address_offset : 0x0 Bytes (0x0)
size : -1 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BODVL : BOD Voltage Level
bits : 0 - 3 (4 bit)
access : read-write
BODHYS : BOD Hysteresis
bits : 4 - 4 (1 bit)
access : read-write
Enumeration:
#0 : 0
Hysteresis Disabled
#1 : 1
Enable Hysteresis of BOD detection
End of enumeration elements list.
Brown Out Detector Timer Register
address_offset : 0x10 Bytes (0x0)
size : -1 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
DURTOFF : Time BOD Detector Is Off
(DURTOFF+1)*100us . Minimum value is 7. (default is 99.6ms)
bits : 0 - 15 (16 bit)
access : read-write
DURTON : Time BOD Detector Is Active
(DURTON+1) * 100us. Minimum value is 1. (default is 400us)
bits : 16 - 19 (4 bit)
access : read-write
Brown Out Detector Enable Register
address_offset : 0x4 Bytes (0x0)
size : -1 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
BODEN : BOD Enable
bits : 0 - 1 (2 bit)
access : read-write
BODINTEN : BOD Interrupt Enable
bits : 2 - 2 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disable BOD Interrupt
#1 : 1
Enable BOD Interrupt
End of enumeration elements list.
BODIF : Current Status of Interrupt
bits : 3 - 3 (1 bit)
access : read-write
BODOUT : Output of BOD Detection Block
bits : 4 - 4 (1 bit)
access : read-write
BODRST : BOD Reset
1: Reset device when BOD is triggered.
bits : 5 - 5 (1 bit)
access : read-write
LVR_EN : Low Voltage Reset (LVR) Enable (Initialized and Protected Bit)
The LVR function resets the chip when the input power voltage is lower than LVR trip point. Default value is set by flash controller as inverse of CLVR config0[27].
bits : 16 - 16 (1 bit)
access : read-write
Enumeration:
#0 : 0
Disable LVR function
#1 : 1
Enable LVR function
End of enumeration elements list.
LVR_FILTER : Default value is 00.
bits : 17 - 18 (2 bit)
access : read-write
Enumeration:
#00 : 0
LVR output will be filtered by 1 HCLK
#01 : 1
LVR output will be filtered by 2 HCLK
#10 : 2
LVR output will be filtered by 8 HCLK
#11 : 3
LVR output will be filtered by 15 HCLK
End of enumeration elements list.
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.