UARTn_DAT

UARTn_MODEM

UARTn_MODEMSTS

UARTn_FIFOSTS

UARTn_INTSTS

UARTn_TOUT

UARTn_BAUD

UARTn_IRDA

UARTn_ALTCTL

UARTn_FUNCSEL

UARTn_INTEN

UARTn_FIFO

UARTn_LINE

DAT : Receive FIFO Register Reading this register will return data from the receive data FIFO. By reading this register, the UART will return the 8-bit data received from Rx pin (LSB first).
bits : 0 - 7 (8 bit)
access : read-write

RTS : RTS (Request-to-send) Signal
bits : 1 - 1 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

LBMEN : Loopback Mode Enable
bits : 4 - 4 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

RTSACTLV : Request-to-send (RTS) Active Trigger Level This bit can change the RTS trigger level.
bits : 9 - 9 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

RTSSTS : RTS Pin State (Read Only) This bit is the pin status of RTS.
bits : 13 - 13 (1 bit)
access : read-only

CTSDETF : Detect CTS State Change Flag NOTE: This bit is cleared by writing 1 to itself.
bits : 0 - 0 (1 bit)
access : read-write

CTSSTS : CTS Pin Status (Read Only) This bit is the pin status of CTS.
bits : 4 - 4 (1 bit)
access : read-only

CTSACTLV : Clear-to-send (CTS) Active Trigger Level This bit can change the CTS trigger level.
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

RXOVIF : Rx Overflow Error Interrupt Flag If the Rx FIFO (UART_DAT) is full, and an additional byte is received by the UART, an overflow condition will occur and set this bit to logic 1. It will also generate a BUFERRIF event and interrupt if enabled. NOTE: This bit is cleared by writing 1 to itself.
bits : 0 - 0 (1 bit)
access : read-write

PEF : Parity Error Flag This bit is set to logic 1 whenever the received character does not have a valid parity bit , and is reset whenever the CPU writes 1 to this bit.
bits : 4 - 4 (1 bit)
access : read-write

FEF : Framing Error Flag This bit is set to logic 1 whenever the received character does not have a valid stop bit (that is, the stop bit following the last data bit or parity bit is detected as a logic 0), and is reset whenever the CPU writes 1 to this bit.
bits : 5 - 5 (1 bit)
access : read-write

BIF : Break Interrupt Flag This bit is set to a logic 1 whenever the receive data input (Rx) is held in the space state (logic 0) for longer than a full word transmission time (that is, the total time of start bit + data bits + parity + stop bits). It is reset whenever the CPU writes 1 to this bit.
bits : 6 - 6 (1 bit)
access : read-write

RXPTR : Rx FIFO Pointer (Read Only) This field returns the Rx FIFO buffer pointer. It is the number of bytes available for read in the Rx FIFO. When UART receives one byte from external device, RXPTR is incremented. When one byte of Rx FIFO is read by CPU, RXPTR is decremented.
bits : 8 - 13 (6 bit)
access : read-only

RXEMPTY : Receive FIFO Empty (Read Only) This bit indicates whether the Rx FIFO is empty or not. When the last byte of Rx FIFO has been read by CPU, hardware sets this bit high. It will be cleared when UART receives any new data.
bits : 14 - 14 (1 bit)
access : read-only

RXFULL : Receive FIFO Full (Read Only) This bit indicates whether the Rx FIFO is full or not. This bit is set when Rx FIFO is full otherwise it is cleared by hardware.
bits : 15 - 15 (1 bit)
access : read-only

TXPTR : Tx FIFO Pointer (Read Only) This field returns the Tx FIFO buffer pointer. When CPU writes a byte into the Tx FIFO, TXPTR is incremented. When a byte from Tx FIFO is transferred to the Transmit Shift Register, TXPTR is decremented.
bits : 16 - 21 (6 bit)
access : read-only

TXEMPTY : Transmit FIFO Empty (Read Only) This bit indicates whether the Tx FIFO is empty or not. When the last byte of Tx FIFO has been transferred to Transmitter Shift Register, hardware sets this bit high. It will be cleared after writing data to FIFO (Tx FIFO not empty).
bits : 22 - 22 (1 bit)
access : read-only

TXFULL : Transmit FIFO Full (Read Only) This bit indicates whether the Tx FIFO is full or not.
bits : 23 - 23 (1 bit)
access : read-only

TXOVIF : Tx Overflow Error Interrupt Flag If the Tx FIFO (UART_DAT) is full, an additional write to UART_DAT will cause an overflow condition and set this bit to logic 1. It will also generate a BUFERRIF event and interrupt if enabled. NOTE: This bit is cleared by writing 1 to itself.
bits : 24 - 24 (1 bit)
access : read-write

TXEMPTYF : Transmitter Empty (Read Only) Bit is set by hardware when Tx FIFO is empty and the STOP bit of the last byte has been transmitted. Bit is cleared automatically when Tx FIFO is not empty or the last byte transmission has not completed. NOTE: This bit is read only.
bits : 28 - 28 (1 bit)
access : read-only

RDAIF : Receive Data Available Interrupt Flag (Read Only) When the number of bytes in the Rx FIFO equals UART_FIFO.RFITL then the RDAIF will be set. If UART_INTEN.RDAIEN is enabled, the RDA interrupt will be generated. NOTE: This bit is read only and it will be cleared when the number of unread bytes of Rx FIFO drops below the threshold level (RFITL).
bits : 0 - 0 (1 bit)
access : read-only

THREIF : Transmit Holding Register Empty Interrupt Flag (Read Only) This bit is set when the last data of Tx FIFO is transferred to Transmitter Shift Register. If UART_INTEN.THREIEN is enabled, the THRE interrupt will be generated. NOTE: This bit is read only and it will be cleared when writing data into the Tx FIFO.
bits : 1 - 1 (1 bit)
access : read-only

RLSIF : Receive Line Status Interrupt Flag (Read Only) This bit is set when the Rx receive data has a parity, framing or break error (at least one of, UART_FIFOSTS.BIF, UART_FIFOSTS.FEF and UART_FIFOSTS.PEF, is set). If UART_INTEN.RLSIEN is enabled, the RLS interrupt will be generated. NOTE: This bit is read only and reset to 0 when all bits of BIF, FEF and PEF are cleared.
bits : 2 - 2 (1 bit)
access : read-only

MODENIF : MODEM Interrupt Flag (Read Only) NOTE: This bit is read only and reset when bit UART_MODEMSTS.CTSDETF is cleared by a write 1.
bits : 3 - 3 (1 bit)
access : read-only

RXTOIF : Time Out Interrupt Flag (Read Only) This bit is set when the Rx FIFO is not empty and no activity occurs in the Rx FIFO and the time out counter equal to TOIC. If UART_INTEN.TOUT_IEN is enabled a CPU interrupt request will be generated. NOTE: This bit is read only and user can read FIFO to clear it.
bits : 4 - 4 (1 bit)
access : read-only

BUFERRIF : Buffer Error Interrupt Flag (Read Only) This bit is set when either the Tx or Rx FIFO overflows (UART_FIFOSTS.TXOVIF or UART_FIFOSTS.RXOVIF is set). When BUFERRIF is set, the serial transfer may be corrupted. If UART_INTEN.BUFERRIEN is enabled a CPU interrupt request will be generated. NOTE: This bit is cleared when both UART_FIFOSTS.TXOVIF and UART_FIFOSTS.RXOVIF are cleared.
bits : 5 - 5 (1 bit)
access : read-only

LINIF : LIN Bus Rx Break Field Detected Flag This bit is set when LIN controller detects a break field. This bit is cleared by writing a 1.
bits : 7 - 7 (1 bit)
access : read-write

RDAINT : Receive Data Available Interrupt Indicator to Interrupt Controller Logical AND of UART_INTEN.RDAIEN and RDAIF.
bits : 8 - 8 (1 bit)
access : read-write

THERINT : Transmit Holding Register Empty Interrupt Indicator to Interrupt Controller Logical AND of UART_INTEN.THREIEN and THREIF.
bits : 9 - 9 (1 bit)
access : read-write

RLSINT : Receive Line Status Interrupt Indicator to Interrupt Controller Logical AND of UART_INTEN.RLSIEN and RLSIF.
bits : 10 - 10 (1 bit)
access : read-write

MODEMINT : MODEM Status Interrupt Indicator to Interrupt Logical AND of UART_INTEN.MODEMIEN and MODENIF.
bits : 11 - 11 (1 bit)
access : read-write

RXTOINT : Time Out Interrupt Indicator to Interrupt Controller Logical AND of UART_INTEN.RXTOIEN and RXTOIF.
bits : 12 - 12 (1 bit)
access : read-write

BUFERRINT : Buffer Error Interrupt Indicator to Interrupt Controller Logical AND of UART_INTEN.BUFERRIEN and BUFERRIF.
bits : 13 - 13 (1 bit)
access : read-write

LININT : LIN Bus Rx Break Field Detected Interrupt Indicator to Interrupt Controller Logical AND of UART_INTEN.LINIEN and LINIF.
bits : 15 - 15 (1 bit)
access : read-write

DRLSIF : DMA MODE Receive Line Status Interrupt Flag (Read Only) This bit is set when the Rx receive data has a parity, framing or break error (at least one of, UART_FIFOSTS.BIF, UART_FIFOSTS.FEF and UART_FIFOSTS.PEF, is set). If UART_INTEN.RLSIEN is enabled, the RLS interrupt will be generated. NOTE: This bit is read only and reset to 0 when all bits of BIF, FEF and PEF are cleared.
bits : 18 - 18 (1 bit)
access : read-only

DMODEMIF : DMA MODE MODEM Interrupt Flag (Read Only) NOTE: This bit is read only and reset when bit UART_MODEMSTS.CTSDETF is cleared by a write 1.
bits : 19 - 19 (1 bit)
access : read-only

DRXTOIF : DMA MODE Time Out Interrupt Flag (Read Only) This bit is set when the Rx FIFO is not empty and no activity occurs in the Rx FIFO and the time out counter equal to TOIC. If UART_INTEN.TOUT_IEN is enabled a CPU interrupt request will be generated. NOTE: This bit is read only and user can read FIFO to clear it.
bits : 20 - 20 (1 bit)
access : read-only

DBERRIF : DMA MODE Buffer Error Interrupt Flag (Read Only) This bit is set when either the Tx or Rx FIFO overflows (UART_FIFOSTS.TXOVIF or UART_FIFOSTS.RXOVIF is set). When BUFERRIF is set, the serial transfer may be corrupted. If UART_INTEN.BUFERRIEN is enabled a CPU interrupt request will be generated. NOTE: This bit is cleared when both UART_FIFOSTS.TXOVIF and UART_FIFOSTS.RXOVIF are cleared.
bits : 21 - 21 (1 bit)
access : read-only

DLINIF : DMA MODE LIN Bus Rx Break Field Detected Flag This bit is set when LIN controller detects a break field. This bit is cleared by writing a 1.
bits : 23 - 23 (1 bit)
access : read-write

DRLSINT : DMA MODE Receive Line Status Interrupt Indicator to Interrupt Controller Logical AND of UART_INTEN.DMARXEN or UART_INTEN.DMATXEN and DRLSIF.
bits : 26 - 26 (1 bit)
access : read-write

DMODEMI : DMA MODE MODEM Status Interrupt Indicator to Interrupt Logical AND of UART_INTEN.DMARXEN or UART_INTEN.DMATXEN and DMODENIF.
bits : 27 - 27 (1 bit)
access : read-write

DRXTOINT : DMA MODE Time Out Interrupt Indicator to Interrupt Controller Logical AND of UART_INTEN.DMARXEN or UART_INTEN.DMATXEN and DRXTOIF.
bits : 28 - 28 (1 bit)
access : read-write

DBERRINT : DMA MODE Buffer Error Interrupt Indicator to Interrupt Controller Logical AND of UART_INTEN.DMARXEN or UART_INTEN.DMATXEN and DBERRIF.
bits : 29 - 29 (1 bit)
access : read-write

DLININT : DMA MODE LIN Bus Rx Break Field Detected Interrupt Indicator to Interrupt Controller Logical AND of UART_INTEN.DMARXEN or UART_INTEN.DMATXEN and DLINIF.
bits : 31 - 31 (1 bit)
access : read-write

TOIC : Time Out Interrupt Comparator The time out counter resets and starts counting whenever the Rx FIFO receives a new data word. Once the content of time out counter is equal to that of time out interrupt comparator (TOIC), a receiver time out interrupt (RXTOINT) is generated if UART_INTEN.RXTOIEN is set. A new incoming data word or RX FIFO empty clears RXTOIF. The period of the time out counter is the baud rate.
bits : 0 - 6 (7 bit)
access : read-write

BRD : Baud Rate Divider Refer to Table 5116 UART Baud Rate Setting Table for more information.
bits : 0 - 15 (16 bit)
access : read-write

EDIVM1 : Divider x
bits : 24 - 27 (4 bit)
access : read-write

BAUDM0 : Divider X Equal 1 Refer to Table 5116 UART Baud Rate Setting Table for more information.
bits : 28 - 28 (1 bit)
access : read-write

BAUDM1 : Divider X Enable Refer to Table 5116 UART Baud Rate Setting Table for more information. NOTE: When in IrDA mode, this bit must disabled.
bits : 29 - 29 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

TXEN : Transmit/Receive Selection
bits : 1 - 1 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

LOOPBACK : IrDA Loopback Test Mode Loopback Tx to Rx.
bits : 2 - 2 (1 bit)
access : read-write

TXINV : Transmit Inversion Enable
bits : 5 - 5 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

RXINV : Receive Inversion Enable
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

BRKFL : UART LIN Break Field Length Count This field indicates a 4-bit LIN Tx break field count. NOTE: This break field length is BRKFL + 2
bits : 0 - 3 (4 bit)
access : read-write

LINRXEN : LIN RX Enable
bits : 6 - 6 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

LINTXEN : LIN TX Break Mode Enable NOTE: When Tx break field transfer operation finished, this bit will be cleared automatically.
bits : 7 - 7 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

LINEN : Enable LIN Function Note that IrDA and LIN functions are mutually exclusive: both cannot be active at same time.
bits : 0 - 0 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

IRDAEN : Enable IrDA Function
bits : 1 - 1 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

RDAIEN : Receive Data Available Interrupt Enable
bits : 0 - 0 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

THREIEN : Transmit FIFO Register Empty Interrupt Enable
bits : 1 - 1 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

RLSIEN : Receive Line Status Interrupt Enable
bits : 2 - 2 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

MODEMIEN : Modem Status Interrupt Enable
bits : 3 - 3 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

RXTOIEN : Receive Time Out Interrupt Enable
bits : 4 - 4 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

BUFERRIEN : Buffer Error Interrupt Enable
bits : 5 - 5 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

LINIEN : LIN RX Break Field Detected Interrupt Enable
bits : 8 - 8 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

TOCNTEN : Time-out Counter Enable
bits : 11 - 11 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

ATORTSEN : RTS Auto Flow Control Enable When RTS auto-flow is enabled, if the number of bytes in the Rx FIFO equals UART_FIFO.RTSTRGLV, the UART will de-assert the RTS signal.
bits : 12 - 12 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

ATOCTSEN : CTS Auto Flow Control Enable When CTS auto-flow is enabled, the UART will send data to external device when CTS input is asserted (UART will not send data to device until CTS is asserted).
bits : 13 - 13 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

DMATXEN : Transmit DMA Enable If enabled, the UART will request DMA service when space is available in transmit FIFO.
bits : 14 - 14 (1 bit)
access : read-write

DMARXEN : Receive DMA Enable If enabled, the UART will request DMA service when data is available in receive FIFO.
bits : 15 - 15 (1 bit)
access : read-write

RXRST : Receive FIFO Reset When RXRST is set, all the bytes in the receive FIFO are cleared and receive internal state machine is reset. Note: This bit will auto-clear after 3 UART engine clock cycles.
bits : 1 - 1 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

TXRST : Transmit FIFO Reset When TXRST is set, all the bytes in the transmit FIFO are cleared and transmit internal state machine is reset. Note: This bit will auto-clear after 3 UART engine clock cycles.
bits : 2 - 2 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

RFITL : Receive FIFO Interrupt (RDAINT) Trigger Level When the number of bytes in the receive FIFO equals the RFITL then the RDAIF will be set and, if enabled, an RDAINT interrupt will generated. Value : INTR_RDA Trigger Level (Bytes) 0 : 1 1 : 4
bits : 4 - 7 (4 bit)
access : read-write

RTSTRGLV : RTS Trigger Level for Auto-flow Control Sets the FIFO trigger level when auto-flow control will de-assert RTS (request-to-send). Value : Trigger Level (Bytes) 0 : 1 1 : 4 2 : 8
bits : 16 - 19 (4 bit)
access : read-write

WLS : Word Length Select 0 (5bits), 1(6bits), 2(7bits), 3(8bits)
bits : 0 - 1 (2 bit)
access : read-write

NSB : Number of STOP Bits
bits : 2 - 2 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

PBE : Parity Bit Enable
bits : 3 - 3 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

EPE : Even Parity Enable This bit has effect only when PBE (parity bit enable) is set.
bits : 4 - 4 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

SPE : Stick Parity Enable
bits : 5 - 5 (1 bit)
access : read-write

Enumeration:

End of enumeration elements list.

BCB : Break Control Bit When this bit is set to logic 1, the serial data output (Tx) is forced to the 'Space' state (logic 0). Normal condition is serial data output is 'Mark' state. This bit acts only on Tx and has no effect on the transmitter logic.
bits : 6 - 6 (1 bit)
access : read-write