Embeetle, an IDE designed from scratch for embedded software developers.address_offset : 0x0 Bytes (0x0)
size : 0x220 byte (0x0)
mem_usage : registers
protection :
Pad Configuration Register A
address_offset : 0x0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PAD0PULL : Pad 0 pullup enable
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD0INPEN : Pad 0 input enable
bits : 1 - 2 (2 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD0STRNG : Pad 0 drive strength
bits : 2 - 4 (3 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD0FNCSEL : Pad 0 function select
bits : 3 - 8 (6 bit)
access : read-write
Enumeration:
0 : SLSCL
Configure as the IOSLAVE I2C SCL signal
1 : SLSCK
Configure as the IOSLAVE SPI SCK signal
2 : UARTTX
Configure as the UART TX signal
3 : GPIO0
Configure as GPIO0
4 : M0SCK
Configure as the IOSLAVE SPI SCK loopback signal from IOMSTR0
5 : M1SCK
Configure as the IOSLAVE SPI SCK loopback signal from IOMSTR1
6 : M0SCL
Configure as the IOSLAVE I2C SCL loopback signal from IOMSTR0
7 : M1SCL
Configure as the IOSLAVE I2C SCL loopback signal from IOMSTR1
End of enumeration elements list.
PAD1PULL : Pad 1 pullup enable
bits : 8 - 16 (9 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD1INPEN : Pad 1 input enable
bits : 9 - 18 (10 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD1STRNG : Pad 1 drive strength
bits : 10 - 20 (11 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD1FNCSEL : Pad 1 function select
bits : 11 - 24 (14 bit)
access : read-write
Enumeration:
0 : SLSDA
Configure as the IOSLAVE I2C SDA signal
1 : SLMISO
Configure as the IOSLAVE SPI MISO signal
2 : UARTRX
Configure as the UART RX signal
3 : GPIO1
Configure as GPIO1
4 : M0MISO
Configure as the IOSLAVE SPI MISO loopback signal from IOMSTR0
5 : M1MISO
Configure as the IOSLAVE SPI MISO loopback signal from IOMSTR1
6 : M0SDA
Configure as the IOSLAVE I2C SDA loopback signal from IOMSTR0
7 : M1SDA
Configure as the IOSLAVE I2C SDA loopback signal from IOMSTR1
End of enumeration elements list.
PAD2PULL : Pad 2 pullup enable
bits : 16 - 32 (17 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD2INPEN : Pad 2 input enable
bits : 17 - 34 (18 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD2STRNG : Pad 2 drive strength
bits : 18 - 36 (19 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD2FNCSEL : Pad 2 function select
bits : 19 - 40 (22 bit)
access : read-write
Enumeration:
0 : SLWIR3
Configure as the IOSLAVE SPI 3-wire MOSI/MISO signal
1 : SLMOSI
Configure as the IOSLAVE SPI MOSI signal
2 : CLKOUT
Configure as the CLKOUT signal
3 : GPIO2
Configure as GPIO2
4 : M0MOSI
Configure as the IOSLAVE SPI MOSI loopback signal from IOMSTR0
5 : M1MOSI
Configure as the IOSLAVE SPI MOSI loopback signal from IOMSTR1
6 : M0WIR3
Configure as the IOSLAVE SPI 3-wire MOSI/MISO loopback signal from IOMSTR0
7 : M1WIR3
Configure as the IOSLAVE SPI 3-wire MOSI/MISO loopback signal from IOMSTR1
End of enumeration elements list.
PAD3PULL : Pad 3 pullup enable
bits : 24 - 48 (25 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD3INPEN : Pad 3 input enable.
bits : 25 - 50 (26 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD3STRNG : Pad 3 drive strength.
bits : 26 - 52 (27 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD3FNCSEL : Pad 3 function select
bits : 27 - 56 (30 bit)
access : read-write
Enumeration:
0 : TRIG0
Configure as the ADC Trigger 0 signal
1 : SLnCE
Configure as the IOSLAVE SPI nCE signal
2 : M1nCE4
Configure as the SPI channel 4 nCE signal from IOMSTR1
3 : GPIO3
Configure as GPIO3
4 : M0nCE
Configure as the IOSLAVE SPI nCE loopback signal from IOMSTR0
5 : M1nCE
Configure as the IOSLAVE SPI nCE loopback signal from IOMSTR1
6 : DIS
Pad disabled
End of enumeration elements list.
PAD3PWRUP : Pad 3 upper power switch enable
bits : 31 - 62 (32 bit)
access : read-write
Enumeration:
0 : DIS
Power switch disabled
1 : EN
Power switch enabled
End of enumeration elements list.
Pad Configuration Register E
address_offset : 0x10 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PAD16PULL : Pad 16 pullup enable
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD16INPEN : Pad 16 input enable
bits : 1 - 2 (2 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD16STRNG : Pad 16 drive strength
bits : 2 - 4 (3 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD16FNCSEL : Pad 16 function select
bits : 3 - 7 (5 bit)
access : read-write
Enumeration:
0 : ADCREF
Configure as the analog ADC reference input signal
1 : M0nCE4
Configure as the SPI channel 4 nCE signal from IOMSTR0
2 : TRIG2
Configure as the ADC Trigger 2 signal
3 : GPIO16
Configure as GPIO16
End of enumeration elements list.
PAD17PULL : Pad 17 pullup enable
bits : 8 - 16 (9 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD17INPEN : Pad 17 input enable
bits : 9 - 18 (10 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD17STRNG : Pad 17 drive strength
bits : 10 - 20 (11 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD17FNCSEL : Pad 17 function select
bits : 11 - 24 (14 bit)
access : read-write
Enumeration:
0 : CMPIN0
Configure as the analog comparator input 0 signal
1 : M0nCE1
Configure as the SPI channel 1 nCE signal from IOMSTR0
2 : TRIG3
Configure as the ADC Trigger 3 signal
3 : GPIO17
Configure as GPIO17
5 : EXTLF
Configure as the external LFRC clock signal
7 : DIS
Pad disabled
End of enumeration elements list.
PAD18PULL : Pad 18 pullup enable
bits : 16 - 32 (17 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD18INPEN : Pad 18 input enable
bits : 17 - 34 (18 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD18STRNG : Pad 18 drive strength
bits : 18 - 36 (19 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD18FNCSEL : Pad 18 function select
bits : 19 - 39 (21 bit)
access : read-write
Enumeration:
0 : CMPIN1
Configure as the analog comparator input 1 signal
1 : M0nCE2
Configure as the SPI channel 2 nCE signal from IOMSTR0
2 : TCTA1
Configure as the input/output signal from CTIMER A1
3 : GPIO18
Configure as GPIO18
End of enumeration elements list.
PAD19PULL : Pad 19 pullup enable
bits : 24 - 48 (25 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD19INPEN : Pad 19 input enable
bits : 25 - 50 (26 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD19STRNG : Pad 19 drive strentgh
bits : 26 - 52 (27 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD19FNCSEL : Pad 19 function select
bits : 27 - 55 (29 bit)
access : read-write
Enumeration:
0 : CMPRF
Configure as the analog comparator reference signal
1 : M0nCE3
Configure as the SPI channel 3 nCE signal from IOMSTR0
2 : TCTB1
Configure as the input/output signal from CTIMER B1
3 : GPIO19
Configure as GPIO19
End of enumeration elements list.
Pad Configuration Register F
address_offset : 0x14 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PAD20PULL : Pad 20 pulldown enable
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
0 : DIS
Pulldown disabled
1 : EN
Pulldown enabled
End of enumeration elements list.
PAD20INPEN : Pad 20 input enable
bits : 1 - 2 (2 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD20STRNG : Pad 20 drive strength
bits : 2 - 4 (3 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD20FNCSEL : Pad 20 function select
bits : 3 - 7 (5 bit)
access : read-write
Enumeration:
0 : SWDCK
Configure as the serial wire debug clock signal
1 : M1nCE5
Configure as the SPI channel 5 nCE signal from IOMSTR1
2 : TCTA2
Configure as the input/output signal from CTIMER A2
3 : GPIO20
Configure as GPIO20
End of enumeration elements list.
PAD21PULL : Pad 21 pullup enable
bits : 8 - 16 (9 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD21INPEN : Pad 21 input enable
bits : 9 - 18 (10 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD21STRNG : Pad 21 drive strength
bits : 10 - 20 (11 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD21FNCSEL : Pad 21 function select
bits : 11 - 23 (13 bit)
access : read-write
Enumeration:
0 : SWDIO
Configure as the serial wire debug data signal
1 : M1nCE6
Configure as the SPI channel 6 nCE signal from IOMSTR1
2 : TCTB2
Configure as the input/output signal from CTIMER B2
3 : GPIO21
Configure as GPIO21
End of enumeration elements list.
PAD22PULL : Pad 22 pullup enable
bits : 16 - 32 (17 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD22INPEN : Pad 22 input enable
bits : 17 - 34 (18 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD22STRNG : Pad 22 drive strength
bits : 18 - 36 (19 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD22FNCSEL : Pad 22 function select
bits : 19 - 39 (21 bit)
access : read-write
Enumeration:
0 : UARTTX
Configure as the UART TX signal
1 : M1nCE7
Configure as the SPI channel 7 nCE signal from IOMSTR1
2 : TCTA3
Configure as the input/output signal from CTIMER A3
3 : GPIO22
Configure as GPIO22
End of enumeration elements list.
PAD23PULL : Pad 23 pullup enable
bits : 24 - 48 (25 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD23INPEN : Pad 23 input enable
bits : 25 - 50 (26 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD23STRNG : Pad 23 drive strentgh
bits : 26 - 52 (27 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD23FNCSEL : Pad 23 function select
bits : 27 - 55 (29 bit)
access : read-write
Enumeration:
0 : UARTRX
Configure as the UART RX signal
1 : M0nCE0
Configure as the SPI channel 0 nCE signal from IOMSTR0
2 : TCTB3
Configure as the input/output signal from CTIMER B3
3 : GPIO23
Configure as GPIO23
End of enumeration elements list.
Pad Configuration Register G
address_offset : 0x18 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PAD24PULL : Pad 24 pullup enable
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD24INPEN : Pad 24 input enable
bits : 1 - 2 (2 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD24STRNG : Pad 24 drive strength
bits : 2 - 4 (3 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD24FNCSEL : Pad 24 function select
bits : 3 - 7 (5 bit)
access : read-write
Enumeration:
0 : DIS
Pad disabled
1 : M0nCE1
Configure as the SPI channel 1 nCE signal from IOMSTR0
2 : CLKOUT
Configure as the CLKOUT signal
3 : GPIO24
Configure as GPIO24
End of enumeration elements list.
PAD25PULL : Pad 25 pullup enable
bits : 8 - 16 (9 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD25INPEN : Pad 25 input enable
bits : 9 - 18 (10 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD25STRNG : Pad 25 drive strength
bits : 10 - 20 (11 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD25FNCSEL : Pad 25 function select
bits : 11 - 23 (13 bit)
access : read-write
Enumeration:
0 : EXTXT
Configure as the external XT clock signal
1 : M0nCE2
Configure as the SPI channel 2 nCE signal from IOMSTR0
2 : TCTA0
Configure as the input/output signal from CTIMER A0
3 : GPIO25
Configure as GPIO25
End of enumeration elements list.
PAD26PULL : Pad 26 pullup enable
bits : 16 - 32 (17 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD26INPEN : Pad 26 input enable
bits : 17 - 34 (18 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD26STRNG : Pad 26 drive strength
bits : 18 - 36 (19 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD26FNCSEL : Pad 26 function select
bits : 19 - 39 (21 bit)
access : read-write
Enumeration:
0 : EXTLF
Configure as the external LFRC clock signal
1 : M0nCE3
Configure as the SPI channel 3 nCE signal from IOMSTR0
2 : TCTB0
Configure as the input/output signal from CTIMER B0
3 : GPIO26
Configure as GPIO26
End of enumeration elements list.
PAD27PULL : Pad 27 pullup enable
bits : 24 - 48 (25 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD27INPEN : Pad 27 input enable
bits : 25 - 50 (26 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD27STRNG : Pad 27 drive strentgh
bits : 26 - 52 (27 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD27FNCSEL : Pad 27 function select
bits : 27 - 55 (29 bit)
access : read-write
Enumeration:
0 : EXTHF
Configure as the external HFRC clock signal
1 : M1nCE4
Configure as the SPI channel 4 nCE signal from IOMSTR1
2 : TCTA1
Configure as the input/output signal from CTIMER A1
3 : GPIO27
Configure as GPIO27
End of enumeration elements list.
Pad Configuration Register H
address_offset : 0x1C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PAD28PULL : Pad 28 pullup enable
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD28INPEN : Pad 28 input enable
bits : 1 - 2 (2 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD28STRNG : Pad 28 drive strength
bits : 2 - 4 (3 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD28FNCSEL : Pad 28 function select
bits : 3 - 7 (5 bit)
access : read-write
Enumeration:
0 : DIS
Pad disabled
1 : M1nCE5
Configure as the SPI channel 5 nCE signal from IOMSTR1
2 : TCTB1
Configure as the input/output signal from CTIMER B1
3 : GPIO28
Configure as GPIO28
End of enumeration elements list.
PAD29PULL : Pad 29 pullup enable
bits : 8 - 16 (9 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD29INPEN : Pad 29 input enable
bits : 9 - 18 (10 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD29STRNG : Pad 29 drive strength
bits : 10 - 20 (11 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD29FNCSEL : Pad 29 function select
bits : 11 - 23 (13 bit)
access : read-write
Enumeration:
0 : ADC4
Configure as the analog ADC input 4 signal
1 : M1nCE6
Configure as the SPI channel 6 nCE signal from IOMSTR1
2 : TCTA2
Configure as the input/output signal from CTIMER A2
3 : GPIO29
Configure as GPIO29
End of enumeration elements list.
PAD30PULL : Pad 30 pullup enable
bits : 16 - 32 (17 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD30INPEN : Pad 30 input enable
bits : 17 - 34 (18 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD30STRNG : Pad 30 drive strength
bits : 18 - 36 (19 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD30FNCSEL : Pad 30 function select
bits : 19 - 39 (21 bit)
access : read-write
Enumeration:
0 : ADC5
Configure as the analog ADC input 5 signal
1 : M1nCE7
Configure as the SPI channel 7 nCE signal from IOMSTR1
2 : TCTB2
Configure as the input/output signal from CTIMER B2
3 : GPIO30
Configure as GPIO30
End of enumeration elements list.
PAD31PULL : Pad 31 pullup enable
bits : 24 - 48 (25 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD31INPEN : Pad 31 input enable
bits : 25 - 50 (26 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD31STRNG : Pad 31 drive strentgh
bits : 26 - 52 (27 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD31FNCSEL : Pad 31 function select
bits : 27 - 55 (29 bit)
access : read-write
Enumeration:
0 : ADC6
Configure as the analog ADC input 6 signal
1 : M0nCE4
Configure as the SPI channel 4 nCE signal from IOMSTR0
2 : TCTA3
Configure as the input/output signal from CTIMER A3
3 : GPIO31
Configure as GPIO31
End of enumeration elements list.
Pad Configuration Register I
address_offset : 0x20 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PAD32PULL : Pad 32 pullup enable
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD32INPEN : Pad 32 input enable
bits : 1 - 2 (2 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD32STRNG : Pad 32 drive strength
bits : 2 - 4 (3 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD32FNCSEL : Pad 32 function select
bits : 3 - 7 (5 bit)
access : read-write
Enumeration:
0 : ADC7
Configure as the analog ADC input 7 signal
1 : M0nCE5
Configure as the SPI channel 5 nCE signal from IOMSTR0
2 : TCTB3
Configure as the input/output signal from CTIMER B3
3 : GPIO32
Configure as GPIO32
End of enumeration elements list.
PAD33PULL : Pad 33 pullup enable
bits : 8 - 16 (9 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD33INPEN : Pad 33 input enable
bits : 9 - 18 (10 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD33STRNG : Pad 33 drive strength
bits : 10 - 20 (11 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD33FNCSEL : Pad 33 function select
bits : 11 - 23 (13 bit)
access : read-write
Enumeration:
0 : CMPRF1
Configure as the analog comparator reference 1 signal
1 : M0nCE6
Configure as the SPI channel 6 nCE signal from IOMSTR0
2 : DIS
Pad disabled
3 : GPIO33
Configure as GPIO33
End of enumeration elements list.
PAD34PULL : Pad 34 pullup enable
bits : 16 - 32 (17 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD34INPEN : Pad 34 input enable
bits : 17 - 34 (18 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD34STRNG : Pad 34 drive strength
bits : 18 - 36 (19 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD34FNCSEL : Pad 34 function select
bits : 19 - 39 (21 bit)
access : read-write
Enumeration:
0 : CMPRF2
Configure as the analog comparator reference 2 signal
1 : M0nCE7
Configure as the SPI channel 7 nCE signal from IOMSTR0
2 : DIS
Pad disabled
3 : GPIO34
Configure as GPIO34
End of enumeration elements list.
PAD35PULL : Pad 35 pullup enable
bits : 24 - 48 (25 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD35INPEN : Pad 35 input enable
bits : 25 - 50 (26 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD35STRNG : Pad 35 drive strentgh
bits : 26 - 52 (27 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD35FNCSEL : Pad 35 function select
bits : 27 - 55 (29 bit)
access : read-write
Enumeration:
0 : DIS
Pad disabled
1 : M1nCE0
Configure as the SPI channel 0 nCE signal from IOMSTR1
2 : UARTTX
Configure as the UART TX signal
3 : GPIO35
Configure as GPIO35
End of enumeration elements list.
GPIO Interrupt Registers 31-0: Enable
address_offset : 0x200 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
GPIO0 : GPIO0 interrupt.
bits : 0 - 0 (1 bit)
access : read-write
GPIO1 : GPIO1 interrupt.
bits : 1 - 2 (2 bit)
access : read-write
GPIO2 : GPIO2 interrupt.
bits : 2 - 4 (3 bit)
access : read-write
GPIO3 : GPIO3 interrupt.
bits : 3 - 6 (4 bit)
access : read-write
GPIO4 : GPIO4 interrupt.
bits : 4 - 8 (5 bit)
access : read-write
GPIO5 : GPIO5 interrupt.
bits : 5 - 10 (6 bit)
access : read-write
GPIO6 : GPIO6 interrupt.
bits : 6 - 12 (7 bit)
access : read-write
GPIO7 : GPIO7 interrupt.
bits : 7 - 14 (8 bit)
access : read-write
GPIO8 : GPIO8 interrupt.
bits : 8 - 16 (9 bit)
access : read-write
GPIO9 : GPIO9 interrupt.
bits : 9 - 18 (10 bit)
access : read-write
GPIO10 : GPIO10 interrupt.
bits : 10 - 20 (11 bit)
access : read-write
GPIO11 : GPIO11 interrupt.
bits : 11 - 22 (12 bit)
access : read-write
GPIO12 : GPIO12 interrupt.
bits : 12 - 24 (13 bit)
access : read-write
GPIO13 : GPIO13 interrupt.
bits : 13 - 26 (14 bit)
access : read-write
GPIO14 : GPIO14 interrupt.
bits : 14 - 28 (15 bit)
access : read-write
GPIO15 : GPIO15 interrupt.
bits : 15 - 30 (16 bit)
access : read-write
GPIO16 : GPIO16 interrupt.
bits : 16 - 32 (17 bit)
access : read-write
GPIO17 : GPIO17 interrupt.
bits : 17 - 34 (18 bit)
access : read-write
GPIO18 : GPIO18interrupt.
bits : 18 - 36 (19 bit)
access : read-write
GPIO19 : GPIO19 interrupt.
bits : 19 - 38 (20 bit)
access : read-write
GPIO20 : GPIO20 interrupt.
bits : 20 - 40 (21 bit)
access : read-write
GPIO21 : GPIO21 interrupt.
bits : 21 - 42 (22 bit)
access : read-write
GPIO22 : GPIO22 interrupt.
bits : 22 - 44 (23 bit)
access : read-write
GPIO23 : GPIO23 interrupt.
bits : 23 - 46 (24 bit)
access : read-write
GPIO24 : GPIO24 interrupt.
bits : 24 - 48 (25 bit)
access : read-write
GPIO25 : GPIO25 interrupt.
bits : 25 - 50 (26 bit)
access : read-write
GPIO26 : GPIO26 interrupt.
bits : 26 - 52 (27 bit)
access : read-write
GPIO27 : GPIO27 interrupt.
bits : 27 - 54 (28 bit)
access : read-write
GPIO28 : GPIO28 interrupt.
bits : 28 - 56 (29 bit)
access : read-write
GPIO29 : GPIO29 interrupt.
bits : 29 - 58 (30 bit)
access : read-write
GPIO30 : GPIO30 interrupt.
bits : 30 - 60 (31 bit)
access : read-write
GPIO31 : GPIO31 interrupt.
bits : 31 - 62 (32 bit)
access : read-write
GPIO Interrupt Registers 31-0: Status
address_offset : 0x204 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
GPIO0 : GPIO0 interrupt.
bits : 0 - 0 (1 bit)
access : read-write
GPIO1 : GPIO1 interrupt.
bits : 1 - 2 (2 bit)
access : read-write
GPIO2 : GPIO2 interrupt.
bits : 2 - 4 (3 bit)
access : read-write
GPIO3 : GPIO3 interrupt.
bits : 3 - 6 (4 bit)
access : read-write
GPIO4 : GPIO4 interrupt.
bits : 4 - 8 (5 bit)
access : read-write
GPIO5 : GPIO5 interrupt.
bits : 5 - 10 (6 bit)
access : read-write
GPIO6 : GPIO6 interrupt.
bits : 6 - 12 (7 bit)
access : read-write
GPIO7 : GPIO7 interrupt.
bits : 7 - 14 (8 bit)
access : read-write
GPIO8 : GPIO8 interrupt.
bits : 8 - 16 (9 bit)
access : read-write
GPIO9 : GPIO9 interrupt.
bits : 9 - 18 (10 bit)
access : read-write
GPIO10 : GPIO10 interrupt.
bits : 10 - 20 (11 bit)
access : read-write
GPIO11 : GPIO11 interrupt.
bits : 11 - 22 (12 bit)
access : read-write
GPIO12 : GPIO12 interrupt.
bits : 12 - 24 (13 bit)
access : read-write
GPIO13 : GPIO13 interrupt.
bits : 13 - 26 (14 bit)
access : read-write
GPIO14 : GPIO14 interrupt.
bits : 14 - 28 (15 bit)
access : read-write
GPIO15 : GPIO15 interrupt.
bits : 15 - 30 (16 bit)
access : read-write
GPIO16 : GPIO16 interrupt.
bits : 16 - 32 (17 bit)
access : read-write
GPIO17 : GPIO17 interrupt.
bits : 17 - 34 (18 bit)
access : read-write
GPIO18 : GPIO18interrupt.
bits : 18 - 36 (19 bit)
access : read-write
GPIO19 : GPIO19 interrupt.
bits : 19 - 38 (20 bit)
access : read-write
GPIO20 : GPIO20 interrupt.
bits : 20 - 40 (21 bit)
access : read-write
GPIO21 : GPIO21 interrupt.
bits : 21 - 42 (22 bit)
access : read-write
GPIO22 : GPIO22 interrupt.
bits : 22 - 44 (23 bit)
access : read-write
GPIO23 : GPIO23 interrupt.
bits : 23 - 46 (24 bit)
access : read-write
GPIO24 : GPIO24 interrupt.
bits : 24 - 48 (25 bit)
access : read-write
GPIO25 : GPIO25 interrupt.
bits : 25 - 50 (26 bit)
access : read-write
GPIO26 : GPIO26 interrupt.
bits : 26 - 52 (27 bit)
access : read-write
GPIO27 : GPIO27 interrupt.
bits : 27 - 54 (28 bit)
access : read-write
GPIO28 : GPIO28 interrupt.
bits : 28 - 56 (29 bit)
access : read-write
GPIO29 : GPIO29 interrupt.
bits : 29 - 58 (30 bit)
access : read-write
GPIO30 : GPIO30 interrupt.
bits : 30 - 60 (31 bit)
access : read-write
GPIO31 : GPIO31 interrupt.
bits : 31 - 62 (32 bit)
access : read-write
GPIO Interrupt Registers 31-0: Clear
address_offset : 0x208 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
GPIO0 : GPIO0 interrupt.
bits : 0 - 0 (1 bit)
access : read-write
GPIO1 : GPIO1 interrupt.
bits : 1 - 2 (2 bit)
access : read-write
GPIO2 : GPIO2 interrupt.
bits : 2 - 4 (3 bit)
access : read-write
GPIO3 : GPIO3 interrupt.
bits : 3 - 6 (4 bit)
access : read-write
GPIO4 : GPIO4 interrupt.
bits : 4 - 8 (5 bit)
access : read-write
GPIO5 : GPIO5 interrupt.
bits : 5 - 10 (6 bit)
access : read-write
GPIO6 : GPIO6 interrupt.
bits : 6 - 12 (7 bit)
access : read-write
GPIO7 : GPIO7 interrupt.
bits : 7 - 14 (8 bit)
access : read-write
GPIO8 : GPIO8 interrupt.
bits : 8 - 16 (9 bit)
access : read-write
GPIO9 : GPIO9 interrupt.
bits : 9 - 18 (10 bit)
access : read-write
GPIO10 : GPIO10 interrupt.
bits : 10 - 20 (11 bit)
access : read-write
GPIO11 : GPIO11 interrupt.
bits : 11 - 22 (12 bit)
access : read-write
GPIO12 : GPIO12 interrupt.
bits : 12 - 24 (13 bit)
access : read-write
GPIO13 : GPIO13 interrupt.
bits : 13 - 26 (14 bit)
access : read-write
GPIO14 : GPIO14 interrupt.
bits : 14 - 28 (15 bit)
access : read-write
GPIO15 : GPIO15 interrupt.
bits : 15 - 30 (16 bit)
access : read-write
GPIO16 : GPIO16 interrupt.
bits : 16 - 32 (17 bit)
access : read-write
GPIO17 : GPIO17 interrupt.
bits : 17 - 34 (18 bit)
access : read-write
GPIO18 : GPIO18interrupt.
bits : 18 - 36 (19 bit)
access : read-write
GPIO19 : GPIO19 interrupt.
bits : 19 - 38 (20 bit)
access : read-write
GPIO20 : GPIO20 interrupt.
bits : 20 - 40 (21 bit)
access : read-write
GPIO21 : GPIO21 interrupt.
bits : 21 - 42 (22 bit)
access : read-write
GPIO22 : GPIO22 interrupt.
bits : 22 - 44 (23 bit)
access : read-write
GPIO23 : GPIO23 interrupt.
bits : 23 - 46 (24 bit)
access : read-write
GPIO24 : GPIO24 interrupt.
bits : 24 - 48 (25 bit)
access : read-write
GPIO25 : GPIO25 interrupt.
bits : 25 - 50 (26 bit)
access : read-write
GPIO26 : GPIO26 interrupt.
bits : 26 - 52 (27 bit)
access : read-write
GPIO27 : GPIO27 interrupt.
bits : 27 - 54 (28 bit)
access : read-write
GPIO28 : GPIO28 interrupt.
bits : 28 - 56 (29 bit)
access : read-write
GPIO29 : GPIO29 interrupt.
bits : 29 - 58 (30 bit)
access : read-write
GPIO30 : GPIO30 interrupt.
bits : 30 - 60 (31 bit)
access : read-write
GPIO31 : GPIO31 interrupt.
bits : 31 - 62 (32 bit)
access : read-write
GPIO Interrupt Registers 31-0: Set
address_offset : 0x20C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
GPIO0 : GPIO0 interrupt.
bits : 0 - 0 (1 bit)
access : read-write
GPIO1 : GPIO1 interrupt.
bits : 1 - 2 (2 bit)
access : read-write
GPIO2 : GPIO2 interrupt.
bits : 2 - 4 (3 bit)
access : read-write
GPIO3 : GPIO3 interrupt.
bits : 3 - 6 (4 bit)
access : read-write
GPIO4 : GPIO4 interrupt.
bits : 4 - 8 (5 bit)
access : read-write
GPIO5 : GPIO5 interrupt.
bits : 5 - 10 (6 bit)
access : read-write
GPIO6 : GPIO6 interrupt.
bits : 6 - 12 (7 bit)
access : read-write
GPIO7 : GPIO7 interrupt.
bits : 7 - 14 (8 bit)
access : read-write
GPIO8 : GPIO8 interrupt.
bits : 8 - 16 (9 bit)
access : read-write
GPIO9 : GPIO9 interrupt.
bits : 9 - 18 (10 bit)
access : read-write
GPIO10 : GPIO10 interrupt.
bits : 10 - 20 (11 bit)
access : read-write
GPIO11 : GPIO11 interrupt.
bits : 11 - 22 (12 bit)
access : read-write
GPIO12 : GPIO12 interrupt.
bits : 12 - 24 (13 bit)
access : read-write
GPIO13 : GPIO13 interrupt.
bits : 13 - 26 (14 bit)
access : read-write
GPIO14 : GPIO14 interrupt.
bits : 14 - 28 (15 bit)
access : read-write
GPIO15 : GPIO15 interrupt.
bits : 15 - 30 (16 bit)
access : read-write
GPIO16 : GPIO16 interrupt.
bits : 16 - 32 (17 bit)
access : read-write
GPIO17 : GPIO17 interrupt.
bits : 17 - 34 (18 bit)
access : read-write
GPIO18 : GPIO18interrupt.
bits : 18 - 36 (19 bit)
access : read-write
GPIO19 : GPIO19 interrupt.
bits : 19 - 38 (20 bit)
access : read-write
GPIO20 : GPIO20 interrupt.
bits : 20 - 40 (21 bit)
access : read-write
GPIO21 : GPIO21 interrupt.
bits : 21 - 42 (22 bit)
access : read-write
GPIO22 : GPIO22 interrupt.
bits : 22 - 44 (23 bit)
access : read-write
GPIO23 : GPIO23 interrupt.
bits : 23 - 46 (24 bit)
access : read-write
GPIO24 : GPIO24 interrupt.
bits : 24 - 48 (25 bit)
access : read-write
GPIO25 : GPIO25 interrupt.
bits : 25 - 50 (26 bit)
access : read-write
GPIO26 : GPIO26 interrupt.
bits : 26 - 52 (27 bit)
access : read-write
GPIO27 : GPIO27 interrupt.
bits : 27 - 54 (28 bit)
access : read-write
GPIO28 : GPIO28 interrupt.
bits : 28 - 56 (29 bit)
access : read-write
GPIO29 : GPIO29 interrupt.
bits : 29 - 58 (30 bit)
access : read-write
GPIO30 : GPIO30 interrupt.
bits : 30 - 60 (31 bit)
access : read-write
GPIO31 : GPIO31 interrupt.
bits : 31 - 62 (32 bit)
access : read-write
GPIO Interrupt Registers 49-32: Enable
address_offset : 0x210 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
GPIO32 : GPIO32 interrupt.
bits : 0 - 0 (1 bit)
access : read-write
GPIO33 : GPIO33 interrupt.
bits : 1 - 2 (2 bit)
access : read-write
GPIO34 : GPIO34 interrupt.
bits : 2 - 4 (3 bit)
access : read-write
GPIO35 : GPIO35 interrupt.
bits : 3 - 6 (4 bit)
access : read-write
GPIO36 : GPIO36 interrupt.
bits : 4 - 8 (5 bit)
access : read-write
GPIO37 : GPIO37 interrupt.
bits : 5 - 10 (6 bit)
access : read-write
GPIO38 : GPIO38 interrupt.
bits : 6 - 12 (7 bit)
access : read-write
GPIO39 : GPIO39 interrupt.
bits : 7 - 14 (8 bit)
access : read-write
GPIO40 : GPIO40 interrupt.
bits : 8 - 16 (9 bit)
access : read-write
GPIO41 : GPIO41 interrupt.
bits : 9 - 18 (10 bit)
access : read-write
GPIO42 : GPIO42 interrupt.
bits : 10 - 20 (11 bit)
access : read-write
GPIO43 : GPIO43 interrupt.
bits : 11 - 22 (12 bit)
access : read-write
GPIO44 : GPIO44 interrupt.
bits : 12 - 24 (13 bit)
access : read-write
GPIO45 : GPIO45 interrupt.
bits : 13 - 26 (14 bit)
access : read-write
GPIO46 : GPIO46 interrupt.
bits : 14 - 28 (15 bit)
access : read-write
GPIO47 : GPIO47 interrupt.
bits : 15 - 30 (16 bit)
access : read-write
GPIO48 : GPIO48 interrupt.
bits : 16 - 32 (17 bit)
access : read-write
GPIO49 : GPIO49 interrupt.
bits : 17 - 34 (18 bit)
access : read-write
GPIO Interrupt Registers 49-32: Status
address_offset : 0x214 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
GPIO32 : GPIO32 interrupt.
bits : 0 - 0 (1 bit)
access : read-write
GPIO33 : GPIO33 interrupt.
bits : 1 - 2 (2 bit)
access : read-write
GPIO34 : GPIO34 interrupt.
bits : 2 - 4 (3 bit)
access : read-write
GPIO35 : GPIO35 interrupt.
bits : 3 - 6 (4 bit)
access : read-write
GPIO36 : GPIO36 interrupt.
bits : 4 - 8 (5 bit)
access : read-write
GPIO37 : GPIO37 interrupt.
bits : 5 - 10 (6 bit)
access : read-write
GPIO38 : GPIO38 interrupt.
bits : 6 - 12 (7 bit)
access : read-write
GPIO39 : GPIO39 interrupt.
bits : 7 - 14 (8 bit)
access : read-write
GPIO40 : GPIO40 interrupt.
bits : 8 - 16 (9 bit)
access : read-write
GPIO41 : GPIO41 interrupt.
bits : 9 - 18 (10 bit)
access : read-write
GPIO42 : GPIO42 interrupt.
bits : 10 - 20 (11 bit)
access : read-write
GPIO43 : GPIO43 interrupt.
bits : 11 - 22 (12 bit)
access : read-write
GPIO44 : GPIO44 interrupt.
bits : 12 - 24 (13 bit)
access : read-write
GPIO45 : GPIO45 interrupt.
bits : 13 - 26 (14 bit)
access : read-write
GPIO46 : GPIO46 interrupt.
bits : 14 - 28 (15 bit)
access : read-write
GPIO47 : GPIO47 interrupt.
bits : 15 - 30 (16 bit)
access : read-write
GPIO48 : GPIO48 interrupt.
bits : 16 - 32 (17 bit)
access : read-write
GPIO49 : GPIO49 interrupt.
bits : 17 - 34 (18 bit)
access : read-write
GPIO Interrupt Registers 49-32: Clear
address_offset : 0x218 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
GPIO32 : GPIO32 interrupt.
bits : 0 - 0 (1 bit)
access : read-write
GPIO33 : GPIO33 interrupt.
bits : 1 - 2 (2 bit)
access : read-write
GPIO34 : GPIO34 interrupt.
bits : 2 - 4 (3 bit)
access : read-write
GPIO35 : GPIO35 interrupt.
bits : 3 - 6 (4 bit)
access : read-write
GPIO36 : GPIO36 interrupt.
bits : 4 - 8 (5 bit)
access : read-write
GPIO37 : GPIO37 interrupt.
bits : 5 - 10 (6 bit)
access : read-write
GPIO38 : GPIO38 interrupt.
bits : 6 - 12 (7 bit)
access : read-write
GPIO39 : GPIO39 interrupt.
bits : 7 - 14 (8 bit)
access : read-write
GPIO40 : GPIO40 interrupt.
bits : 8 - 16 (9 bit)
access : read-write
GPIO41 : GPIO41 interrupt.
bits : 9 - 18 (10 bit)
access : read-write
GPIO42 : GPIO42 interrupt.
bits : 10 - 20 (11 bit)
access : read-write
GPIO43 : GPIO43 interrupt.
bits : 11 - 22 (12 bit)
access : read-write
GPIO44 : GPIO44 interrupt.
bits : 12 - 24 (13 bit)
access : read-write
GPIO45 : GPIO45 interrupt.
bits : 13 - 26 (14 bit)
access : read-write
GPIO46 : GPIO46 interrupt.
bits : 14 - 28 (15 bit)
access : read-write
GPIO47 : GPIO47 interrupt.
bits : 15 - 30 (16 bit)
access : read-write
GPIO48 : GPIO48 interrupt.
bits : 16 - 32 (17 bit)
access : read-write
GPIO49 : GPIO49 interrupt.
bits : 17 - 34 (18 bit)
access : read-write
GPIO Interrupt Registers 49-32: Set
address_offset : 0x21C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
GPIO32 : GPIO32 interrupt.
bits : 0 - 0 (1 bit)
access : read-write
GPIO33 : GPIO33 interrupt.
bits : 1 - 2 (2 bit)
access : read-write
GPIO34 : GPIO34 interrupt.
bits : 2 - 4 (3 bit)
access : read-write
GPIO35 : GPIO35 interrupt.
bits : 3 - 6 (4 bit)
access : read-write
GPIO36 : GPIO36 interrupt.
bits : 4 - 8 (5 bit)
access : read-write
GPIO37 : GPIO37 interrupt.
bits : 5 - 10 (6 bit)
access : read-write
GPIO38 : GPIO38 interrupt.
bits : 6 - 12 (7 bit)
access : read-write
GPIO39 : GPIO39 interrupt.
bits : 7 - 14 (8 bit)
access : read-write
GPIO40 : GPIO40 interrupt.
bits : 8 - 16 (9 bit)
access : read-write
GPIO41 : GPIO41 interrupt.
bits : 9 - 18 (10 bit)
access : read-write
GPIO42 : GPIO42 interrupt.
bits : 10 - 20 (11 bit)
access : read-write
GPIO43 : GPIO43 interrupt.
bits : 11 - 22 (12 bit)
access : read-write
GPIO44 : GPIO44 interrupt.
bits : 12 - 24 (13 bit)
access : read-write
GPIO45 : GPIO45 interrupt.
bits : 13 - 26 (14 bit)
access : read-write
GPIO46 : GPIO46 interrupt.
bits : 14 - 28 (15 bit)
access : read-write
GPIO47 : GPIO47 interrupt.
bits : 15 - 30 (16 bit)
access : read-write
GPIO48 : GPIO48 interrupt.
bits : 16 - 32 (17 bit)
access : read-write
GPIO49 : GPIO49 interrupt.
bits : 17 - 34 (18 bit)
access : read-write
Pad Configuration Register J
address_offset : 0x24 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PAD36PULL : Pad 36 pullup enable
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD36INPEN : Pad 36 input enable
bits : 1 - 2 (2 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD36STRNG : Pad 36 drive strength
bits : 2 - 4 (3 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD36FNCSEL : Pad 36 function select
bits : 3 - 7 (5 bit)
access : read-write
Enumeration:
0 : DIS
Pad disabled
1 : M1nCE1
Configure as the SPI channel 1 nCE signal from IOMSTR1
2 : UARTRX
Configure as the UART RX signal
3 : GPIO36
Configure as GPIO36
End of enumeration elements list.
PAD37PULL : Pad 37 pullup enable
bits : 8 - 16 (9 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD37INPEN : Pad 37 input enable
bits : 9 - 18 (10 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD37STRNG : Pad 37 drive strength
bits : 10 - 20 (11 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD37FNCSEL : Pad 37 function select
bits : 11 - 23 (13 bit)
access : read-write
Enumeration:
0 : TRIG0
Configure as the ADC Trigger 0 signal
1 : M1nCE2
Configure as the SPI channel 2 nCE signal from IOMSTR1
2 : UARTS
Configure as the UART RTS signal
3 : GPIO37
Configure as GPIO37
End of enumeration elements list.
PAD38PULL : Pad 38 pullup enable
bits : 16 - 32 (17 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD38INPEN : Pad 38 input enable
bits : 17 - 34 (18 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD38STRNG : Pad 38 drive strength
bits : 18 - 36 (19 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD38FNCSEL : Pad 38 function select
bits : 19 - 39 (21 bit)
access : read-write
Enumeration:
0 : TRIG1
Configure as the ADC Trigger 1 signal
1 : M1nCE3
Configure as the SPI channel 3 nCE signal from IOMSTR1
2 : UACTS
Configure as the UART CTS signal
3 : GPIO38
Configure as GPIO38
End of enumeration elements list.
PAD39PULL : Pad 39 pullup enable
bits : 24 - 48 (25 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD39INPEN : Pad 39 input enable
bits : 25 - 50 (26 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD39STRNG : Pad 39 drive strentgh
bits : 26 - 52 (27 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD39FNCSEL : Pad 39 function select
bits : 27 - 55 (29 bit)
access : read-write
Enumeration:
0 : TRIG2
Configure as the ADC Trigger 2 signal
1 : UARTTX
Configure as the UART TX signal
2 : CLKOUT
Configure as the CLKOUT signal
3 : GPIO39
Configure as GPIO39
End of enumeration elements list.
Pad Configuration Register K
address_offset : 0x28 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PAD40PULL : Pad 40 pullup enable
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD40INPEN : Pad 40 input enable
bits : 1 - 2 (2 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD40STRNG : Pad 40 drive strength
bits : 2 - 4 (3 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD40FNCSEL : Pad 40 function select
bits : 3 - 7 (5 bit)
access : read-write
Enumeration:
0 : TRIG3
Configure as the ADC Trigger 3 signal
1 : UARTRX
Configure as the UART RX signal
2 : DIS
Pad disabled
3 : GPIO40
Configure as GPIO40
End of enumeration elements list.
PAD41PULL : Pad 41 pullup enable
bits : 8 - 16 (9 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD41INPEN : Pad 41 input enable
bits : 9 - 18 (10 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD41STRNG : Pad 41 drive strength
bits : 10 - 20 (11 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD41FNCSEL : Pad 41 function select
bits : 11 - 23 (13 bit)
access : read-write
Enumeration:
0 : TRIG4
Configure as the ADC Trigger 4 signal
1 : DIS
Pad disabled
2 : SWO
Configure as the serial wire debug SWO signal
3 : GPIO41
Configure as GPIO41
End of enumeration elements list.
PAD42PULL : Pad 42 pullup enable
bits : 16 - 32 (17 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD42INPEN : Pad 42 input enable
bits : 17 - 34 (18 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD42STRNG : Pad 42 drive strength
bits : 18 - 36 (19 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD42FNCSEL : Pad 42 function select
bits : 19 - 39 (21 bit)
access : read-write
Enumeration:
0 : TRIG5
Configure as the ADC Trigger 5 signal
1 : M0nCE0
Configure as the SPI channel 0 nCE signal from IOMSTR0
2 : TCTA0
Configure as the input/output signal from CTIMER A0
3 : GPIO42
Configure as GPIO42
End of enumeration elements list.
PAD43PULL : Pad 43 pullup enable
bits : 24 - 48 (25 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD43INPEN : Pad 43 input enable
bits : 25 - 50 (26 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD43STRNG : Pad 43 drive strentgh
bits : 26 - 52 (27 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD43FNCSEL : Pad 43 function select
bits : 27 - 55 (29 bit)
access : read-write
Enumeration:
0 : TRIG6
Configure as the ADC Trigger 6 signal
1 : M0nCE1
Configure as the SPI channel 1 nCE signal from IOMSTR0
2 : TCTB0
Configure as the input/output signal from CTIMER B0
3 : GPIO43
Configure as GPIO43
End of enumeration elements list.
Pad Configuration Register L
address_offset : 0x2C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PAD44PULL : Pad 44 pullup enable
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD44INPEN : Pad 44 input enable
bits : 1 - 2 (2 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD44STRNG : Pad 44 drive strength
bits : 2 - 4 (3 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD44FNCSEL : Pad 44 function select
bits : 3 - 7 (5 bit)
access : read-write
Enumeration:
0 : TRIG7
Configure as the ADC Trigger 7 signal
1 : M0nCE2
Configure as the SPI channel 2 nCE signal from IOMSTR0
2 : TCTA1
Configure as the input/output signal from CTIMER A1
3 : GPIO44
Configure as GPIO44
End of enumeration elements list.
PAD45PULL : Pad 45 pullup enable
bits : 8 - 16 (9 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD45INPEN : Pad 45 input enable
bits : 9 - 18 (10 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD45STRNG : Pad 45 drive strength
bits : 10 - 20 (11 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD45FNCSEL : Pad 45 function select
bits : 11 - 23 (13 bit)
access : read-write
Enumeration:
0 : DIS
Pad disabled
1 : M0nCE3
Configure as the SPI channel 3 nCE signal from IOMSTR0
2 : TCTB1
Configure as the input/output signal from CTIMER B1
3 : GPIO45
Configure as GPIO45
End of enumeration elements list.
PAD46PULL : Pad 46 pullup enable
bits : 16 - 32 (17 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD46INPEN : Pad 46 input enable
bits : 17 - 34 (18 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD46STRNG : Pad 46 drive strength
bits : 18 - 36 (19 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD46FNCSEL : Pad 46 function select
bits : 19 - 39 (21 bit)
access : read-write
Enumeration:
0 : DIS
Pad disabled
1 : M0nCE4
Configure as the SPI channel 4 nCE signal from IOMSTR0
2 : TCTA2
Configure as the input/output signal from CTIMER A2
3 : GPIO46
Configure as GPIO46
End of enumeration elements list.
PAD47PULL : Pad 47 pullup enable
bits : 24 - 48 (25 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD47INPEN : Pad 47 input enable
bits : 25 - 50 (26 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD47STRNG : Pad 47 drive strentgh
bits : 26 - 52 (27 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD47FNCSEL : Pad 47 function select
bits : 27 - 55 (29 bit)
access : read-write
Enumeration:
0 : DIS
Pad disabled
1 : M0nCE5
Configure as the SPI channel 5 nCE signal from IOMSTR0
2 : TCTB2
Configure as the input/output signal from CTIMER B2
3 : GPIO47
Configure as GPIO47
End of enumeration elements list.
Pad Configuration Register M
address_offset : 0x30 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PAD48PULL : Pad 48 pullup enable
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD48INPEN : Pad 48 input enable
bits : 1 - 2 (2 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD48STRNG : Pad 48 drive strength
bits : 2 - 4 (3 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD48FNCSEL : Pad 48 function select
bits : 3 - 7 (5 bit)
access : read-write
Enumeration:
0 : DIS
Pad disabled
1 : M0nCE6
Configure as the SPI channel 6 nCE signal from IOMSTR0
2 : TCTA3
Configure as the input/output signal from CTIMER A3
3 : GPIO48
Configure as GPIO48
End of enumeration elements list.
PAD49PULL : Pad 49 pullup enable
bits : 8 - 16 (9 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD49INPEN : Pad 49 input enable
bits : 9 - 18 (10 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD49STRNG : Pad 49 drive strength
bits : 10 - 20 (11 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD49FNCSEL : Pad 49 function select
bits : 11 - 23 (13 bit)
access : read-write
Enumeration:
0 : DIS
Pad disabled
1 : M0nCE7
Configure as the SPI channel 7 nCE signal from IOMSTR0
2 : TCTB3
Configure as the input/output signal from CTIMER B3
3 : GPIO49
Configure as GPIO49
End of enumeration elements list.
Pad Configuration Register B
address_offset : 0x4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PAD4PULL : Pad 4 pullup enable
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD4INPEN : Pad 4 input enable
bits : 1 - 2 (2 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD4STRNG : Pad 4 drive strength
bits : 2 - 4 (3 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD4FNCSEL : Pad 4 function select
bits : 3 - 8 (6 bit)
access : read-write
Enumeration:
0 : TRIG1
Configure as the ADC Trigger 1 signal
1 : SLINT
Configure as the IOSLAVE interrupt out signal
2 : M0nCE5
Configure as the SPI channel 5 nCE signal from IOMSTR0
3 : GPIO4
Configure as GPIO4
4 : SLINTGP
Configure as the IOSLAVE interrupt loopback signal to GPIO4
5 : SWO
Configure as the serial wire debug SWO signal
6 : CLKOUT
Configure as the CLKOUT signal
7 : DIS
Pad disabled
End of enumeration elements list.
PAD4PWRUP : Pad 4 upper power switch enable
bits : 7 - 14 (8 bit)
access : read-write
Enumeration:
0 : DIS
Power switch disabled
1 : EN
Power switch enabled
End of enumeration elements list.
PAD5PULL : Pad 5 pullup enable
bits : 8 - 16 (9 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD5INPEN : Pad 5 input enable
bits : 9 - 18 (10 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD5STRNG : Pad 5 drive strength
bits : 10 - 20 (11 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD5FNCSEL : Pad 5 function select
bits : 11 - 24 (14 bit)
access : read-write
Enumeration:
0 : M0SCL
Configure as the IOMSTR0 I2C SCL signal
1 : M0SCK
Configure as the IOMSTR0 SPI SCK signal
2 : UARTS
Configure as the UART RTS signal
3 : GPIO5
Configure as GPIO5
4 : SLSCK
Configure as the IOMSTR0 SPI SCK loopback signal from IOSLAVE
6 : SLSCL
Configure as the IOMSTR0 I2C SCL loopback signal from IOSLAVE
7 : DIS
Pad disabled
End of enumeration elements list.
PAD5RSEL : Pad 5 pullup resistor selection.
bits : 14 - 29 (16 bit)
access : read-write
Enumeration:
0 : PULL1_5K
Pullup is ~1.5 KOhms
1 : PULL6K
Pullup is ~6 KOhms
2 : PULL12K
Pullup is ~12 KOhms
3 : PULL24K
Pullup is ~24 KOhms
End of enumeration elements list.
PAD6PULL : Pad 6 pullup enable
bits : 16 - 32 (17 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD6INPEN : Pad 6 input enable
bits : 17 - 34 (18 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD6STRNG : Pad 6 drive strength
bits : 18 - 36 (19 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD6FNCSEL : Pad 6 function select
bits : 19 - 40 (22 bit)
access : read-write
Enumeration:
0 : M0SDA
Configure as the IOMSTR0 I2C SDA signal
1 : M0MISO
Configure as the IOMSTR0 SPI MISO signal
2 : UACTS
Configure as the UART CTS signal
3 : GPIO6
Configure as GPIO6
4 : SLMISO
Configure as the IOMSTR0 SPI MISO loopback signal from IOSLAVE
6 : SLSDA
Configure as the IOMSTR0 I2C SDA loopback signal from IOSLAVE
7 : DIS
Pad disabled
End of enumeration elements list.
PAD6RSEL : Pad 6 pullup resistor selection.
bits : 22 - 45 (24 bit)
access : read-write
Enumeration:
0 : PULL1_5K
Pullup is ~1.5 KOhms
1 : PULL6K
Pullup is ~6 KOhms
2 : PULL12K
Pullup is ~12 KOhms
3 : PULL24K
Pullup is ~24 KOhms
End of enumeration elements list.
PAD7PULL : Pad 7 pullup enable
bits : 24 - 48 (25 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD7INPEN : Pad 7 input enable
bits : 25 - 50 (26 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD7STRNG : Pad 7 drive strentgh
bits : 26 - 52 (27 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD7FNCSEL : Pad 7 function select
bits : 27 - 56 (30 bit)
access : read-write
Enumeration:
0 : M0WIR3
Configure as the IOMSTR0 SPI 3-wire MOSI/MISO signal
1 : M0MOSI
Configure as the IOMSTR0 SPI MOSI signal
2 : CLKOUT
Configure as the CLKOUT signal
3 : GPIO7
Configure as GPIO7
6 : SLWIR3
Configure as the IOMSTR0 SPI 3-wire MOSI/MISO loopback signal from IOSLAVE
7 : DIS
Pad disabled
End of enumeration elements list.
GPIO Configuration Register A
address_offset : 0x40 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
GPIO0INCFG : GPIO0 input enable.
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO0OUTCFG : GPIO0 output configuration.
bits : 1 - 3 (3 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO0INTD : GPIO0 interrupt direction.
bits : 3 - 6 (4 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO1INCFG : GPIO1 input enable.
bits : 4 - 8 (5 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO1OUTCFG : GPIO1 output configuration.
bits : 5 - 11 (7 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO1INTD : GPIO1 interrupt direction.
bits : 7 - 14 (8 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO2INCFG : GPIO2 input enable.
bits : 8 - 16 (9 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO2OUTCFG : GPIO2 output configuration.
bits : 9 - 19 (11 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO2INTD : GPIO2 interrupt direction.
bits : 11 - 22 (12 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO3INCFG : GPIO3 input enable.
bits : 12 - 24 (13 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO3OUTCFG : GPIO3 output configuration.
bits : 13 - 27 (15 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO3INTD : GPIO3 interrupt direction.
bits : 15 - 30 (16 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO4INCFG : GPIO4 input enable.
bits : 16 - 32 (17 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO4OUTCFG : GPIO4 output configuration.
bits : 17 - 35 (19 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO4INTD : GPIO4 interrupt direction.
bits : 19 - 38 (20 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO5INCFG : GPIO5 input enable.
bits : 20 - 40 (21 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO5OUTCFG : GPIO5 output configuration.
bits : 21 - 43 (23 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO5INTD : GPIO5 interrupt direction.
bits : 23 - 46 (24 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO6INCFG : GPIO6 input enable.
bits : 24 - 48 (25 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO6OUTCFG : GPIO6 output configuration.
bits : 25 - 51 (27 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO6INTD : GPIO6 interrupt direction.
bits : 27 - 54 (28 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO7INCFG : GPIO7 input enable.
bits : 28 - 56 (29 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO7OUTCFG : GPIO7 output configuration.
bits : 29 - 59 (31 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO7INTD : GPIO7 interrupt direction.
bits : 31 - 62 (32 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO Configuration Register B
address_offset : 0x44 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
GPIO8INCFG : GPIO8 input enable.
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO8OUTCFG : GPIO8 output configuration.
bits : 1 - 3 (3 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO8INTD : GPIO8 interrupt direction.
bits : 3 - 6 (4 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO9INCFG : GPIO9 input enable.
bits : 4 - 8 (5 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO9OUTCFG : GPIO9 output configuration.
bits : 5 - 11 (7 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO9INTD : GPIO9 interrupt direction.
bits : 7 - 14 (8 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO10INCFG : GPIO10 input enable.
bits : 8 - 16 (9 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO10OUTCFG : GPIO10 output configuration.
bits : 9 - 19 (11 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO10INTD : GPIO10 interrupt direction.
bits : 11 - 22 (12 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO11INCFG : GPIO11 input enable.
bits : 12 - 24 (13 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO11OUTCFG : GPIO11 output configuration.
bits : 13 - 27 (15 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO11INTD : GPIO11 interrupt direction.
bits : 15 - 30 (16 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO12INCFG : GPIO12 input enable.
bits : 16 - 32 (17 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO12OUTCFG : GPIO12 output configuration.
bits : 17 - 35 (19 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO12INTD : GPIO12 interrupt direction.
bits : 19 - 38 (20 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO13INCFG : GPIO13 input enable.
bits : 20 - 40 (21 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO13OUTCFG : GPIO13 output configuration.
bits : 21 - 43 (23 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO13INTD : GPIO13 interrupt direction.
bits : 23 - 46 (24 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO14INCFG : GPIO14 input enable.
bits : 24 - 48 (25 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO14OUTCFG : GPIO14 output configuration.
bits : 25 - 51 (27 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO14INTD : GPIO14 interrupt direction.
bits : 27 - 54 (28 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO15INCFG : GPIO15 input enable.
bits : 28 - 56 (29 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO15OUTCFG : GPIO15 output configuration.
bits : 29 - 59 (31 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO15INTD : GPIO15 interrupt direction.
bits : 31 - 62 (32 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO Configuration Register C
address_offset : 0x48 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
GPIO16INCFG : GPIO16 input enable.
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO16OUTCFG : GPIO16 output configuration.
bits : 1 - 3 (3 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO16INTD : GPIO16 interrupt direction.
bits : 3 - 6 (4 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO17INCFG : GPIO17 input enable.
bits : 4 - 8 (5 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO17OUTCFG : GPIO17 output configuration.
bits : 5 - 11 (7 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO17INTD : GPIO17 interrupt direction.
bits : 7 - 14 (8 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO18INCFG : GPIO18 input enable.
bits : 8 - 16 (9 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO18OUTCFG : GPIO18 output configuration.
bits : 9 - 19 (11 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO18INTD : GPIO18 interrupt direction.
bits : 11 - 22 (12 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO19INCFG : GPIO19 input enable.
bits : 12 - 24 (13 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO19OUTCFG : GPIO19 output configuration.
bits : 13 - 27 (15 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO19INTD : GPIO19 interrupt direction.
bits : 15 - 30 (16 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO20INCFG : GPIO20 input enable.
bits : 16 - 32 (17 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO20OUTCFG : GPIO20 output configuration.
bits : 17 - 35 (19 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO20INTD : GPIO20 interrupt direction.
bits : 19 - 38 (20 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO21INCFG : GPIO21 input enable.
bits : 20 - 40 (21 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO21OUTCFG : GPIO21 output configuration.
bits : 21 - 43 (23 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO21INTD : GPIO21 interrupt direction.
bits : 23 - 46 (24 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO22INCFG : GPIO22 input enable.
bits : 24 - 48 (25 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO22OUTCFG : GPIO22 output configuration.
bits : 25 - 51 (27 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO22INTD : GPIO22 interrupt direction.
bits : 27 - 54 (28 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO23INCFG : GPIO23 input enable.
bits : 28 - 56 (29 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO23OUTCFG : GPIO23 output configuration.
bits : 29 - 59 (31 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO23INTD : GPIO23 interrupt direction.
bits : 31 - 62 (32 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO Configuration Register D
address_offset : 0x4C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
GPIO24INCFG : GPIO24 input enable.
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO24OUTCFG : GPIO24 output configuration.
bits : 1 - 3 (3 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO24INTD : GPIO24 interrupt direction.
bits : 3 - 6 (4 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO25INCFG : GPIO25 input enable.
bits : 4 - 8 (5 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO25OUTCFG : GPIO25 output configuration.
bits : 5 - 11 (7 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO25INTD : GPIO25 interrupt direction.
bits : 7 - 14 (8 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO26INCFG : GPIO26 input enable.
bits : 8 - 16 (9 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO26OUTCFG : GPIO26 output configuration.
bits : 9 - 19 (11 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO26INTD : GPIO26 interrupt direction.
bits : 11 - 22 (12 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO27INCFG : GPIO27 input enable.
bits : 12 - 24 (13 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO27OUTCFG : GPIO27 output configuration.
bits : 13 - 27 (15 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO27INTD : GPIO27 interrupt direction.
bits : 15 - 30 (16 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO28INCFG : GPIO28 input enable.
bits : 16 - 32 (17 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO28OUTCFG : GPIO28 output configuration.
bits : 17 - 35 (19 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO28INTD : GPIO28 interrupt direction.
bits : 19 - 38 (20 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO29INCFG : GPIO29 input enable.
bits : 20 - 40 (21 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO29OUTCFG : GPIO29 output configuration.
bits : 21 - 43 (23 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO29INTD : GPIO29 interrupt direction.
bits : 23 - 46 (24 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO30INCFG : GPIO30 input enable.
bits : 24 - 48 (25 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO30OUTCFG : GPIO30 output configuration.
bits : 25 - 51 (27 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO30INTD : GPIO30 interrupt direction.
bits : 27 - 54 (28 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO31INCFG : GPIO31 input enable.
bits : 28 - 56 (29 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO31OUTCFG : GPIO31 output configuration.
bits : 29 - 59 (31 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO31INTD : GPIO31 interrupt direction.
bits : 31 - 62 (32 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO Configuration Register E
address_offset : 0x50 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
GPIO32INCFG : GPIO32 input enable.
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO32OUTCFG : GPIO32 output configuration.
bits : 1 - 3 (3 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO32INTD : GPIO32 interrupt direction.
bits : 3 - 6 (4 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO33INCFG : GPIO33 input enable.
bits : 4 - 8 (5 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO33OUTCFG : GPIO33 output configuration.
bits : 5 - 11 (7 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO33INTD : GPIO33 interrupt direction.
bits : 7 - 14 (8 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO34INCFG : GPIO34 input enable.
bits : 8 - 16 (9 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO34OUTCFG : GPIO34 output configuration.
bits : 9 - 19 (11 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO34INTD : GPIO34 interrupt direction.
bits : 11 - 22 (12 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO35INCFG : GPIO35 input enable.
bits : 12 - 24 (13 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO35OUTCFG : GPIO35 output configuration.
bits : 13 - 27 (15 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO35INTD : GPIO35 interrupt direction.
bits : 15 - 30 (16 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO36INCFG : GPIO36 input enable.
bits : 16 - 32 (17 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO36OUTCFG : GPIO36 output configuration.
bits : 17 - 35 (19 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO36INTD : GPIO36 interrupt direction.
bits : 19 - 38 (20 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO37INCFG : GPIO37 input enable.
bits : 20 - 40 (21 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO37OUTCFG : GPIO37 output configuration.
bits : 21 - 43 (23 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO37INTD : GPIO37 interrupt direction.
bits : 23 - 46 (24 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO38INCFG : GPIO38 input enable.
bits : 24 - 48 (25 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO38OUTCFG : GPIO38 output configuration.
bits : 25 - 51 (27 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO38INTD : GPIO38 interrupt direction.
bits : 27 - 54 (28 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO39INCFG : GPIO39 input enable.
bits : 28 - 56 (29 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO39OUTCFG : GPIO39 output configuration.
bits : 29 - 59 (31 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO39INTD : GPIO39 interrupt direction.
bits : 31 - 62 (32 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO Configuration Register F
address_offset : 0x54 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
GPIO40INCFG : GPIO40 input enable.
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO40OUTCFG : GPIO40 output configuration.
bits : 1 - 3 (3 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO40INTD : GPIO40 interrupt direction.
bits : 3 - 6 (4 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO41INCFG : GPIO41 input enable.
bits : 4 - 8 (5 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO41OUTCFG : GPIO41 output configuration.
bits : 5 - 11 (7 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO41INTD : GPIO41 interrupt direction.
bits : 7 - 14 (8 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO42INCFG : GPIO42 input enable.
bits : 8 - 16 (9 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO42OUTCFG : GPIO42 output configuration.
bits : 9 - 19 (11 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO42INTD : GPIO42 interrupt direction.
bits : 11 - 22 (12 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO43INCFG : GPIO43 input enable.
bits : 12 - 24 (13 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO43OUTCFG : GPIO43 output configuration.
bits : 13 - 27 (15 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO43INTD : GPIO43 interrupt direction.
bits : 15 - 30 (16 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO44INCFG : GPIO44 input enable.
bits : 16 - 32 (17 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO44OUTCFG : GPIO44 output configuration.
bits : 17 - 35 (19 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO44INTD : GPIO44 interrupt direction.
bits : 19 - 38 (20 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO45INCFG : GPIO45 input enable.
bits : 20 - 40 (21 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO45OUTCFG : GPIO45 output configuration.
bits : 21 - 43 (23 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO45INTD : GPIO45 interrupt direction.
bits : 23 - 46 (24 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO46INCFG : GPIO46 input enable.
bits : 24 - 48 (25 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO46OUTCFG : GPIO46 output configuration.
bits : 25 - 51 (27 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO46INTD : GPIO46 interrupt direction.
bits : 27 - 54 (28 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO47INCFG : GPIO47 input enable.
bits : 28 - 56 (29 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO47OUTCFG : GPIO47 output configuration.
bits : 29 - 59 (31 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO47INTD : GPIO47 interrupt direction.
bits : 31 - 62 (32 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO Configuration Register G
address_offset : 0x58 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
GPIO48INCFG : GPIO48 input enable.
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO48OUTCFG : GPIO48 output configuration.
bits : 1 - 3 (3 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO48INTD : GPIO48 interrupt direction.
bits : 3 - 6 (4 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
GPIO49INCFG : GPIO49 input enable.
bits : 4 - 8 (5 bit)
access : read-write
Enumeration:
0 : READ
Read the GPIO pin data
1 : RDZERO
Readback will always be zero
End of enumeration elements list.
GPIO49OUTCFG : GPIO49 output configuration.
bits : 5 - 11 (7 bit)
access : read-write
Enumeration:
0 : DIS
Output disabled
1 : PUSHPULL
Output is push-pull
2 : OD
Output is open drain
3 : TS
Output is tri-state
End of enumeration elements list.
GPIO49INTD : GPIO49 interrupt direction.
bits : 7 - 14 (8 bit)
access : read-write
Enumeration:
0 : INTLH
Interrupt on low to high GPIO transition
1 : INTHL
Interrupt on high to low GPIO transition
End of enumeration elements list.
Key Register for all pad configuration registers
address_offset : 0x60 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PADKEY : Key register value.
bits : 0 - 31 (32 bit)
access : read-write
Enumeration:
115 : Key
Key
End of enumeration elements list.
Pad Configuration Register C
address_offset : 0x8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PAD8PULL : Pad 8 pullup enable
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD8INPEN : Pad 8 input enable
bits : 1 - 2 (2 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD8STRNG : Pad 8 drive strength
bits : 2 - 4 (3 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD8FNCSEL : Pad 8 function select
bits : 3 - 8 (6 bit)
access : read-write
Enumeration:
0 : M1SCL
Configure as the IOMSTR1 I2C SCL signal
1 : M1SCK
Configure as the IOMSTR1 SPI SCK signal
2 : M0nCE4
Configure as the SPI channel 4 nCE signal from IOMSTR0
3 : GPIO8
Configure as GPIO8
5 : SLSCK
Configure as the IOMSTR1 SPI SCK loopback signal from IOSLAVE
6 : DIS
Pad disabled
7 : SLSCL
Configure as the IOMSTR1 I2C SCL loopback signal from IOSLAVE
End of enumeration elements list.
PAD8RSEL : Pad 8 pullup resistor selection.
bits : 6 - 13 (8 bit)
access : read-write
Enumeration:
0 : PULL1_5K
Pullup is ~1.5 KOhms
1 : PULL6K
Pullup is ~6 KOhms
2 : PULL12K
Pullup is ~12 KOhms
3 : PULL24K
Pullup is ~24 KOhms
End of enumeration elements list.
PAD9PULL : Pad 9 pullup enable
bits : 8 - 16 (9 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD9INPEN : Pad 9 input enable
bits : 9 - 18 (10 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD9STRNG : Pad 9 drive strength
bits : 10 - 20 (11 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD9FNCSEL : Pad 9 function select
bits : 11 - 24 (14 bit)
access : read-write
Enumeration:
0 : M1SDA
Configure as the IOMSTR1 I2C SDA signal
1 : M1MISO
Configure as the IOMSTR1 SPI MISO signal
2 : M0nCE5
Configure as the SPI channel 5 nCE signal from IOMSTR0
3 : GPIO9
Configure as GPIO9
5 : SLMISO
Configure as the IOMSTR1 SPI MISO loopback signal from IOSLAVE
6 : DIS
Pad disabled
7 : SLSDA
Configure as the IOMSTR1 I2C SDA loopback signal from IOSLAVE
End of enumeration elements list.
PAD9RSEL : Pad 9 pullup resistor selection
bits : 14 - 29 (16 bit)
access : read-write
Enumeration:
0 : PULL1_5K
Pullup is ~1.5 KOhms
1 : PULL6K
Pullup is ~6 KOhms
2 : PULL12K
Pullup is ~12 KOhms
3 : PULL24K
Pullup is ~24 KOhms
End of enumeration elements list.
PAD10PULL : Pad 10 pullup enable
bits : 16 - 32 (17 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD10INPEN : Pad 10 input enable
bits : 17 - 34 (18 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD10STRNG : Pad 10 drive strength
bits : 18 - 36 (19 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD10FNCSEL : Pad 10 function select
bits : 19 - 40 (22 bit)
access : read-write
Enumeration:
0 : M1WIR3
Configure as the IOMSTR1 SPI 3-wire MOSI/MISO signal
1 : M1MOSI
Configure as the IOMSTR1 SPI MOSI signal
2 : M0nCE6
Configure as the SPI channel 6 nCE signal from IOMSTR0
3 : GPIO10
Configure as GPIO10
5 : EXTHFA
Configure as the external HFRC A clock signal
6 : DIS
Pad disabled
7 : SLWIR3
Configure as the IOMSTR1 SPI 3-wire MOSI/MISO loopback signal from IOSLAVE
End of enumeration elements list.
PAD11PULL : Pad 11 pullup enable
bits : 24 - 48 (25 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD11INPEN : Pad 11 input enable
bits : 25 - 50 (26 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD11STRNG : Pad 11 drive strentgh
bits : 26 - 52 (27 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD11FNCSEL : Pad 11 function select
bits : 27 - 55 (29 bit)
access : read-write
Enumeration:
0 : ANATST
Configure as the analog test output signal
1 : M0nCE0
Configure as the SPI channel 0 nCE signal from IOMSTR0
2 : CLKOUT
Configure as the CLKOUT signal
3 : GPIO11
Configure as GPIO11
End of enumeration elements list.
PAD11PWRDN : Pad 11 lower power switch enable
bits : 30 - 60 (31 bit)
access : read-write
Enumeration:
0 : DIS
Power switch disabled
1 : EN
Power switch enabled
End of enumeration elements list.
GPIO Input Register A
address_offset : 0x80 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RDA : GPIO31-0 read data.
bits : 0 - 31 (32 bit)
access : read-write
GPIO Input Register B
address_offset : 0x84 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
RDB : GPIO49-32 read data.
bits : 0 - 17 (18 bit)
access : read-write
GPIO Output Register A
address_offset : 0x88 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
WTA : GPIO31-0 write data.
bits : 0 - 31 (32 bit)
access : read-write
GPIO Output Register B
address_offset : 0x8C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
WTB : GPIO49-32 write data.
bits : 0 - 17 (18 bit)
access : read-write
GPIO Output Register A Set
address_offset : 0x90 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
WTSA : Set the GPIO31-0 write data.
bits : 0 - 31 (32 bit)
access : read-write
GPIO Output Register B Set
address_offset : 0x94 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
WTSB : Set the GPIO49-32 write data.
bits : 0 - 17 (18 bit)
access : read-write
GPIO Output Register A Clear
address_offset : 0x98 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
WTCA : Clear the GPIO31-0 write data.
bits : 0 - 31 (32 bit)
access : read-write
GPIO Output Register B Clear
address_offset : 0x9C Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
WTCB : Clear the GPIO49-32 write data.
bits : 0 - 17 (18 bit)
access : read-write
GPIO Enable Register A
address_offset : 0xA0 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ENA : GPIO31-0 output enables
bits : 0 - 31 (32 bit)
access : read-write
GPIO Enable Register B
address_offset : 0xA4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ENB : GPIO49-32 output enables
bits : 0 - 17 (18 bit)
access : read-write
GPIO Enable Register A Set
address_offset : 0xA8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ENSA : Set the GPIO31-0 output enables
bits : 0 - 31 (32 bit)
access : read-write
GPIO Enable Register B Set
address_offset : 0xAC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ENSB : Set the GPIO49-32 output enables
bits : 0 - 17 (18 bit)
access : read-write
GPIO Enable Register A Clear
address_offset : 0xB4 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ENCA : Clear the GPIO31-0 output enables
bits : 0 - 31 (32 bit)
access : read-write
GPIO Enable Register B Clear
address_offset : 0xB8 Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
ENCB : Clear the GPIO49-32 output enables
bits : 0 - 17 (18 bit)
access : read-write
Pad Configuration Register D
address_offset : 0xC Bytes (0x0)
size : 32 bit
access : read-write
reset_value : 0x0
reset_Mask : 0x0
PAD12PULL : Pad 12 pullup enable
bits : 0 - 0 (1 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD12INPEN : Pad 12 input enable
bits : 1 - 2 (2 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD12STRNG : Pad 12 drive strength
bits : 2 - 4 (3 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD12FNCSEL : Pad 12 function select
bits : 3 - 7 (5 bit)
access : read-write
Enumeration:
0 : ADC0
Configure as the analog ADC input 0
1 : M1nCE0
Configure as the SPI channel 0 nCE signal from IOMSTR1
2 : TCTA0
Configure as the input/output signal from CTIMER A0
3 : GPIO12
Configure as GPIO12
End of enumeration elements list.
PAD13PULL : Pad 13 pullup enable
bits : 8 - 16 (9 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD13INPEN : Pad 13 input enable
bits : 9 - 18 (10 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD13STRNG : Pad 13 drive strength
bits : 10 - 20 (11 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD13FNCSEL : Pad 13 function select
bits : 11 - 24 (14 bit)
access : read-write
Enumeration:
0 : ADC1
Configure as the analog ADC input 1
1 : M1nCE1
Configure as the SPI channel 1 nCE signal from IOMSTR1
2 : TCTB0
Configure as the input/output signal from CTIMER B0
3 : GPIO13
Configure as GPIO13
5 : EXTHFA
Configure as the external HFRC B clock signal
6 : SWO
Configure as the serial wire debug SWO signal
7 : DIS
Pad disabled
End of enumeration elements list.
PAD14PULL : Pad 14 pullup enable
bits : 16 - 32 (17 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD14INPEN : Pad 14 input enable
bits : 17 - 34 (18 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD14STRNG : Pad 14 drive strength
bits : 18 - 36 (19 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD14FNCSEL : Pad 14 function select
bits : 19 - 40 (22 bit)
access : read-write
Enumeration:
0 : ADC2
Configure as the analog ADC input 2
1 : M1nCE2
Configure as the SPI channel 2 nCE signal from IOMSTR1
2 : UARTTX
Configure as the UART TX signal
3 : GPIO14
Configure as GPIO14
5 : EXTHFS
Configure as the external HFRC select signal
7 : DIS
Pad disabled
End of enumeration elements list.
PAD15PULL : Pad 15 pullup enable
bits : 24 - 48 (25 bit)
access : read-write
Enumeration:
0 : DIS
Pullup disabled
1 : EN
Pullup enabled
End of enumeration elements list.
PAD15INPEN : Pad 15 input enable
bits : 25 - 50 (26 bit)
access : read-write
Enumeration:
0 : DIS
Pad input disabled
1 : EN
Pad input enabled
End of enumeration elements list.
PAD15STRNG : Pad 15 drive strentgh
bits : 26 - 52 (27 bit)
access : read-write
Enumeration:
0 : LOW
Low drive strength
1 : HIGH
High drive strength
End of enumeration elements list.
PAD15FNCSEL : Pad 15 function select
bits : 27 - 56 (30 bit)
access : read-write
Enumeration:
0 : ADC3
Configure as the analog ADC input 3
1 : M1nCE3
Configure as the SPI channel 3 nCE signal from IOMSTR1
2 : UARTRX
Configure as the UART RX signal
3 : GPIO15
Configure as GPIO15
5 : EXTXT
Configure as the external XT clock signal
7 : DIS
Pad disabled
End of enumeration elements list.
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.